Loss Predictions in the High-Pressure Film-Cooled Turbine Blade Cascade T120D by Mean of Wall-Resolved Large Eddy Simulation

2020 ◽  
Author(s):  
Mael Harnieh ◽  
Nicolas Odier ◽  
Jérôme Dombard ◽  
Florent Duchaine ◽  
Laurent Gicquel
Keyword(s):  
High Pressure ◽  
Large Eddy Simulation ◽  
Turbine Blade ◽  
Film Cooling ◽  
Load Prediction ◽  
Loss Assessment ◽  
Film Cooling Effectiveness ◽  
Eddy Simulation ◽  
Blade Cascade ◽  
Large Eddy

Abstract Film cooling is commonly used to protect turbine vanes and blades from the hot gases produced in the combustion chamber. The design and optimization of these systems can however only be achieved if a precise prediction of the fluid mechanics and film efficiency is guaranteed at a level where induced losses are fully mastered. Such a prerequisite induces at the numerical level to be able to identify and assess losses. In this context, the present study addresses loss assessment in a wall-resolved Large Eddy Simulation (LES) of the film-cooled high-pressure turbine blade cascade T120D from the European project AITEB II. The objectives are twofolds: (1) to evaluate the capacity of LES to predict adiabatic film cooling effectiveness in a mastered academic case; and (2) to investigate loss generation mechanisms in a fully anisothermal configuration. When it comes to LES predictions of T120D, the flow structure around the blade and the coolant jet organization are coherent with literature findings. Satisfactory agreements are furthermore retrieved for the pressure load prediction as well as the adiabatic film effectiveness if compared to the experiment. Loss generation is then investigated illustrating the fact that aerodynamics losses dominate mixing losses which are mainly located in the coolant film. This is in line with the temperature difference between the hot and coolant flows that is low for this experimental condition. Distinct contributions can however be made available by studying the local loss generation maps by means of Second Law Analysis if recast in the specific context of anisothermal flows when simulated by LES.

scholarly journals Large Eddy Simulation of Film Cooling Involving Compound Angle Holes: Comparative Study of LES and RANS

Processes ◽  
2021 ◽  
Vol 9 (2) ◽  
pp. 198
Author(s):  
Seung Il Baek ◽  
Joon Ahn
Keyword(s):  
Large Eddy Simulation ◽  
Film Cooling ◽  
Orientation Angle ◽  
Turbulence Models ◽  
Film Cooling Effectiveness ◽  
Injection Angle ◽  
Blowing Ratio ◽  
Eddy Simulation ◽  
Large Eddy ◽  
Compound Angle

A large eddy simulation (LES) was performed for film cooling in the gas turbine blade involving spanwise injection angles (orientation angles). For a streamwise coolant injection angle (inclination angle) of 35°, the effects of the orientation angle were compared considering a simple angle of 0° and 30°. Two ratios of the coolant to main flow mass flux (blowing ratio) of 0.5 and 1.0 were considered and the experimental conditions of Jung and Lee (2000) were adopted for the geometry and flow conditions. Moreover, a Reynolds averaged Navier–Stokes simulation (RANS) was performed to understand the characteristics of the turbulence models compared to those in the LES and experiments. In the RANS, three turbulence models were compared, namely, the realizable k-ε, k-ω shear stress transport, and Reynolds stress models. The temperature field and flow fields predicted through the RANS were similar to those obtained through the experiment and LES. Nevertheless, at a simple angle, the point at which the counter-rotating vortex pair (CRVP) collided on the wall and rose was different from that in the experiment and LES. Under the compound angle, the point at which the CRVP changed to a single vortex was different from that in the LES. The adiabatic film cooling effectiveness could not be accurately determined through the RANS but was well reflected by the LES, even under the compound angle. The reattachment of the injectant at a blowing ratio of 1.0 was better predicted by the RANS at the compound angle than at the simple angle. The temperature fluctuation was predicted to decrease slightly when the injectant was supplied at a compound angle.

Loss Predictions in the High-Pressure Film-Cooled Turbine Vane of the FACTOR Project by Mean of Wall-Modeled Large Eddy Simulation

2020 ◽  
Author(s):  
Mael Harnieh ◽  
Nicolas Odier ◽  
Jérôme Dombard ◽  
Florent Duchaine ◽  
Laurent Gicquel
Keyword(s):  
Spatial Distribution ◽  
Large Eddy Simulation ◽  
Film Cooling ◽  
Total Pressure ◽  
Mean Flow ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Eddy Simulation ◽  
Large Eddy ◽  
Turbine Vane

Abstract The use of numerical simulations to design and optimize turbine vane cooling requires precise prediction of the fluid mechanics and film cooling effectiveness. This results in the need to numerically identify and assess the various origins of the losses taking place in such systems and if possible in engine representative conditions. Large-Eddy Simulation (LES) has shown recently its ability to predict turbomachinery flows in well mastered academic cases such as compressor or turbine cascades. When it comes to industrial representative configurations, the geometrical complexities, high Reynolds and Mach numbers as well as boundary condition setup lead to an important increase of CPU cost of the simulations. To evaluate the capacity of LES to predict film cooling effectiveness as well as to investigate the loss generation mechanisms in a turbine vane in engine representative conditions, a wall-modeled LES of the FACTOR film-cooled nozzle is performed. After the comparison of integrated values to validate the operating point of the vanes, the mean flow structure is investigated. In the coolant film, a strong turbulent mixing process between coolant and hot flows is observed. As a result, the spatial distribution of time-averaged vane surface temperature is highly heterogeneous. Comparisons with the experiment show that the LES prediction fairly reproduces the spatial distribution of the adiabatic film effectiveness. The loss generation in the configuration is then investigated. To do so, two methodologies, i.e, performing balance of total pressure in the vanes wakes as mainly used in the literature and Second Law Analysis (SLA) are evaluated. Balance of total pressure without the contribution of thermal effects only highlights the losses generated by the wakes and secondary flows. To overcome this limitation, SLA is adopted by investigating loss maps. Thanks to this approach, mixing losses are shown to dominate in the coolant film while aerodynamic losses dominate in the coolant pipe region.

Large Eddy Simulation of Axial and Compound Angle Holes With Varying Hole Length-to-Diameter Ratio

2017 ◽  
Author(s):  
Weihong Li ◽  
Wei Shi ◽  
Xueying Li ◽  
Jing Ren ◽  
Hongde Jiang
Keyword(s):  
Large Eddy Simulation ◽  
Film Cooling ◽  
Vortex Structures ◽  
Diameter Ratio ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Eddy Simulation ◽  
Large Eddy ◽  
Compound Angle ◽  
Length To Diameter Ratio

The effect of hole length to diameter ratio on flat plate film cooling effectiveness and flow structures of axial and compound angle hole is investigated by large eddy simulation (LES). Film cooling simulations are performed for three blowing ratios (M) ranging from 0.4 to 1.2, three hole length-to-diameter ratios (L/D) from 0.5 to 5 and two compound angle (β: 0°, 45°). The prediction accuracy is validated by the reported hydrodynamic data and present film effectiveness data measured by pressure sensitive paint (PSP). Results indicate that discrete hole with L = 0.5 show highest film cooling effectiveness regardless of compound angle. Round hole generally shows an increasing trend as L increases from 2 to 5, while compound angle hole shows a complex trend concerning with blowing ratios and length to diameter ratios. This is associated with the fact that length-to-diameter ratio influences the in-tube flow behavior, formation of Kelvin-Helmholtz (K-H) structures, and development of single asymmetric main vortex (SAMV). Scalar field transportation features are investigated to clarify how different vortex structures affect the temperature distribution and the film cooling effectiveness. It is also demonstrated that the counter rotating vortex pair (CRVP) which is observed in the time-averaged flow field of axial hole is originated in different vortex structures with varying blowing ratios and length to diameter ratios.

Large Eddy Simulation of Film Cooling over a Flat Plate in Supersonic flow

2020 ◽  
pp. 1-29
Author(s):  
Hitesh Sharma ◽  
Dushyant Singh ◽  
Ashutosh Kumar Singh
Keyword(s):  
Heat Transfer ◽  
Supersonic Flow ◽  
Large Eddy Simulation ◽  
Flat Plate ◽  
Film Cooling ◽  
Cooling Effectiveness ◽  
Potential Core ◽  
Film Cooling Effectiveness ◽  
Eddy Simulation ◽  
Large Eddy

Abstract In the present work, Large Eddy Simulation (LES) was performed to access the film cooling performance in the supersonic flow over a flat plate with a perpendicular slot injection configuration. The study was carried out for three mainstream Mach No.; Mα = 1.2, 2.67, 3.3 and three coolant stream Mach No.; 0.05, 0.1, 0.15. In supersonic flow, temperature rise inside the boundary layer is a major issue considering it causes high rates of heat transfer to the coolant film. To select a suitable LES Sub-Grid Scale (SGS) model, LES results obtained from the present study using the LES Sub-Grid Scale (SGS) models such as Smagorinky- Lilly, Wale, and WMLES models were compared with DNS results available for flow and heat transfer. The parametric study showed that the higher mainstream Mach No. caused increased wall temperature and reduced effectiveness. The film cooling effectiveness appeared to reduce almost by 10% when the mainstream Mach No. is increased from 1.2 to 2.67, however, no apparent difference was observed in effectiveness between the mainstream Mach No. 2.67 and 3.3. It was found that doubling and tripling the coolant stream Mach No. from 0.05 to 0.1 and 0.15, the length of potential core region also doubled and tripled respectively from 4 X/S to 8 X/S and 13 X/S and hence significant improvement in the film cooling effectiveness was observed.

Large-Eddy Simulation of Shaped Hole Film Cooling With the Influence of Cross Flow

2019 ◽  
Author(s):  
Qingsong Wang ◽  
Yifei Li ◽  
Xiutao Bian ◽  
Xinrong Su ◽  
Xin Yuan
Keyword(s):  
Large Eddy Simulation ◽  
Turbine Blade ◽  
Film Cooling ◽  
Cross Flow ◽  
Hairpin Vortices ◽  
Blade Passage ◽  
Eddy Simulation ◽  
Large Eddy ◽  
Cooling Hole ◽  
The Asymmetry

Abstract In the modern highly-loaded gas turbine, due to the large pressure difference between the suction side and the pressure side of the turbine blade, strong cross flow is formed and it strongly affects the aerodynamic and cooling performances in the end-wall region. The film cooling behavior in the environment of strong cross flow is different from the straight channel environment widely studied in the literature. In this research, the effect of cross flow on film cooling is investigated by Large Eddy Simulation (LES) using subgrid-scale (SGS) model. Numerical simulation is carried out in a curved passage to simulate the turbine blade passage. Shaped cooling hole with blowing ratio 1 is studied. The time-averaged friction line results are compared with existing experimental ink trace results. The vortex structures, both time-averaged and instantaneous, are analyzed to study the effect of cross flow on film cooling. At the exit of the cooling hole, the hanging vortices with negative y-vorticity are more flat in shape and closer to the wall in position in contrast to hanging vortex with positive y-vorticity, which is caused by cross flow and results in the asymmetry of hairpin vortices downstream as well as the asymmetry of the distribution of coolant. It has been shown that the vortices from mainstream have a significant impact on the field near the exit of the cooling hole. Those vortices interact with the hairpin vortices from the cooling hole and directly lead to the asymmetry of the hairpin vortices. Proper Orthogonal Decomposition (POD) analysis is further conducted to extract the dominant flow structures and the physical mechanisms of primary POD modes are given to explain the distribution of film cooling effectiveness affected by cross flow. Based on the specific situation in this work, a fast incremental POD (iPOD) approach is adopted since the rank of the field matrix is far less than the rows, which is caused by the tall and thin character of the matrix, which makes the analysis less costly and more effective. This research helps to understand the cooling performance in the real turbine blade passage and to explain the coolant mixing process based on the instantaneous flow field obtained using high precision LES simulation and powerful iPOD.

Sign in / Sign up

Export Citation Format

Share Document