Investigation of the Flow Field and the Pressure Recovery in a Gas Turbine Exhaust Diffuser at Design, Part-Load and Over-Load Condition

2020 ◽  
Author(s):  
Maximilian Bauer ◽  
Simon Hummel ◽  
Markus Schatz ◽  
Martin Kegalj ◽  
Damian M. Vogt
Keyword(s):  
Mach Number ◽  
Flow Field ◽  
Pressure Distribution ◽  
Gas Turbine ◽  
Total Pressure ◽  
Operating Conditions ◽  
Pressure Recovery ◽  
Heavy Duty ◽  
Part Load ◽  
Design Load

Abstract The performance of axial diffusers installed downstream of heavy duty gas turbines is mainly affected by the turbine load. Thereby the outflow varies in Mach number, total pressure distribution, swirl and its tip leakage flow in particular. To investigate the performance of a diffuser at different load conditions, a generic diffuser geometry has been designed at ITSM which is representative for current heavy duty gas turbine diffusers. Results are presented for three different operating conditions, each with and without tip flow respectively. Part-load, design-load and over-load operating conditions are defined and varied at the diffuser inlet in terms of Mach number, total pressure distribution and swirl. Each operating point is investigated experimentally and numerically and assessed based on its flow field as well as the pressure recovery. The diffuser performance shows a strong dependency on the inlet swirl and total pressure profile. A superimposed tip flow only influences the flow field significantly when the casing flow is weakened due to casing separation. In those cases pressure recovery increases with additional tip flow. There is a reliable prediction of the CFD simulations at design-load. At part-load, CFD overpredicts the strut separation, resulting in an underpredicted overall pressure recovery. At over-load, CFD underpredicts the separation extension in the annular diffuser but overpredicts the hub wake. This leads to a better flow control in CFD with the result of an overpredicted overall pressure recovery.

Probabilistic and Numerical Modelling of a Lobed Mixer at Windmilling Conditions

2013 ◽  
Author(s):  
Maxime Lecoq ◽  
Nicholas Grech ◽  
Pavlos K. Zachos ◽  
Vassilios Pachidis
Keyword(s):  
Flow Field ◽  
Response Surface ◽  
Gas Turbine ◽  
Pressure Loss ◽  
Total Pressure ◽  
Engine Performance ◽  
Operating Conditions ◽  
Total Pressure Loss ◽  
Operating Point ◽  
Mixing Losses

Aero-gas turbine engines with a mixed exhaust configuration offer significant benefits to the cycle efficiency relative to separate exhaust systems, such as increase in gross thrust and a reduction in fan pressure ratio required. A number of military and civil engines have a single mixed exhaust system designed to mix out the bypass and core streams. To reduce mixing losses, the two streams are designed to have similar total pressures. In design point whole engine performance solvers, a mixed exhaust is modelled using simple assumptions; momentum balance and a percentage total pressure loss. However at far off-design conditions such as windmilling and altitude relights, the bypass and core streams have very dissimilar total pressures and momentum, with the flow preferring to pass through the bypass duct, increasing drastically the bypass ratio. Mixing of highly dissimilar coaxial streams leads to complex turbulent flow fields for which the simple assumptions and models used in current performance solvers cease to be valid. The effect on simulation results is significant since the nozzle pressure affects critical aspects such as the fan operating point, and therefore the windmilling shaft speeds and air mass flow rates. This paper presents a numerical study on the performance of a lobed mixer under windmilling conditions. An analysis of the flow field is carried out at various total mixer pressure ratios, identifying the onset and nature of recirculation, the flow field characteristics, and the total pressure loss along the mixer as a function of the operating conditions. The data generated from the numerical simulations is used together with a probabilistic approach to generate a response surface in terms of the mass averaged percentage total pressure loss across the mixer, as a function of the engine operating point. This study offers an improved understanding on the complex flows that arise from mixing of highly dissimilar coaxial flows within an aero-gas turbine mixer environment. The total pressure response surface generated using this approach can be used as look-up data for the engine performance solver to include the effects of such turbulent mixing losses.

Design of a Non-Reactive Warm Rig With Real Lean-Premix Combustor Swirlers and Film-Cooled First Stage Nozzles

2020 ◽  
Author(s):  
Simone Cubeda ◽  
Tommaso Bacci ◽  
Lorenzo Mazzei ◽  
Simone Salvadori ◽  
Bruno Facchini ◽  
...  
Keyword(s):  
Flow Field ◽  
Gas Turbine ◽  
Gas Turbines ◽  
Operating Conditions ◽  
Pollutant Emissions ◽  
Heavy Duty ◽  
Design Practices ◽  
Standard Design ◽  
Real Hardware ◽  
Heavy Duty Gas Turbine

Abstract Modern industrial gas turbines typically employ lean-premix combustors, which can limit pollutant emissions thanks to premixed flames, while sustaining high turbine inlet temperatures that increase the single-cycle thermal efficiency. As such, gas-turbine first stage nozzles can be characterized by a highly-swirled and temperature-distorted inlet flow field. However, due to several sources of uncertainty during the design phase, wide safety margins are commonly adopted, having a direct impact on engine performance and efficiency. Therefore, aiming at increasing the knowledge on combustor-turbine interaction and improving standard design practices, a non-reactive test rig composed of real hardware was assembled at the University of Florence, Italy. The rig, accommodating three lean-premix swirlers within a combustion chamber and two first stage film-cooled nozzles of a Baker Hughes heavy-duty gas turbine, is operated in similitude conditions. The rig has been designed to reproduce the real engine periodic flow field on the central vane channel, also allowing for measurements far enough from the lateral walls. The periodicity condition on the central sector was achieved by the proper design of both the angular profile and pitch value of the tailboards with respect to the vanes, which was carried out in a preliminary phase via a Design of Experiments procedure. In addition, circular ducts needed to be installed at the injectors outlet section to preserve the non-reactive swirling flow down to the nozzles’ inlet plane. The combustor-turbine interface section has been experimentally characterized in nominal operating conditions as per the temperature, velocity and pressure fields by means of a five-hole pressure probe provided with a thermocouple, installed on an automatic traverse system. To study the evolution of the combustor outlet flow through the vanes and its interaction with the film-cooling flow, such measurements have been replicated also downstream of the vanes’ trailing edge. This work allowed for designing and providing preliminary data on a combustor simulator capable of equipping and testing real hardware film-cooled nozzles of a heavy-duty gas turbine. Ultimately, the activity sets the basis for an extensive test campaign aimed at characterizing the metal temperature, film effectiveness and heat transfer coefficient at realistic aerothermal conditions. In addition, and by leveraging experimental data, this activity paves the way for a detailed validation of current design practices as well as more advanced numerical methodologies such as Scale-Adaptive Simulations of the integrated combustor-turbine domain.

Aerodynamic Performance Investigation of Modern Marine Gas Turbine Intake System

2012 ◽  
Author(s):  
Peng Sun ◽  
Haiyang Gao ◽  
Jingjun Zhong ◽  
Muxiao Yang
Keyword(s):  
Pressure Distribution ◽  
Gas Turbine ◽  
Gas Turbines ◽  
Pressure Loss ◽  
Total Pressure ◽  
Aerodynamic Performance ◽  
Operating Conditions ◽  
Measuring Point ◽  
Intake System ◽  
Flow Parameters

Gas turbines (GTs) have been used on board for many years. To safe guard these engines working efficiently and stably, several types of air intake system have been employed. The aerodynamic performance of marine gas turbine intake system is one of the important aspects which is associated with the marine operating conditions and should be studied carefully. In this paper, numerical simulation is carried out on the flow parameters of a vessel and her intake system. How vessel operating conditions and the environment conditions influence the intake system inlet boundary is studied firstly. Under some certain assumptions, the intake inlet total pressure value and the angle between wind and heading direction approximately follow the sine law. Then, unsteady simulation is carried out on the intake system. The total pressure loss variation and which measuring point can represent the pressure loss properly are discussed. It is found that the total pressure distribution varies with the measuring location. Following this, flow parameters at the volute outlet is analyzed in detail, especially the flow field structure and the distortion intensity. The total pressure distribution is non-uniform, which will influence the GT performance and stability significantly.

Numerical Investigations of Pollutant Emissions From Novel Heavy-Duty Gas Turbine Burners Operated With Natural Gas

2020 ◽  
Vol 142 (3) ◽  
Author(s):  
Daniele Pampaloni ◽  
Pier Carlo Nassini ◽  
Antonio Andreini ◽  
Bruno Facchini ◽  
Matteo Cerutti
Keyword(s):  
Flow Field ◽  
Gas Turbine ◽  
Design Process ◽  
Gas Turbines ◽  
Operating Conditions ◽  
Pollutant Emissions ◽  
Formation Mechanisms ◽  
Heavy Duty ◽  
Heavy Duty Gas Turbine ◽  
Cost Efficient

Abstract A numerical investigation of pollutant emissions of a novel dry low-emissions burner for heavy-duty gas turbine applications is presented. The objective of this work is to develop and assess a robust and cost-efficient numerical setup for the prediction of NOx and CO emissions in industrial gas turbines and to investigate the pollutant formation mechanisms, thus supporting the design process of a novel low-emission burner. To this end, a comparison against experimental data, from a recent experimental campaign performed by BHGE in cooperation with University of Florence, has been exploited. In the first part of this work, a Reynolds-averaged Navier–Stokes (RANS) approach on both a simplified geometry and the complete domain is adopted to characterize the global flame behavior and validate the numerical setup. Then, unsteady simulations exploiting the scale adaptive simulation (SAS) approach have been performed to assess the prediction improvements that can be obtained with the unsteady modeling of the flame. For all simulations, the flamelet generated manifold (FGM) model has been used, allowing the reliable and cost-efficient application of detailed chemistry mechanisms in computational fluid dynamics (CFD) simulation. However, FGM typically faces issues predicting flame emissions, such as NOx and CO, due to the wide range of time scales involved, from turbulent mixing to pollutant species oxidation. Specific models are typically used to predict NOx emissions, starting from the converged flow-field and introducing additional transport equations. Also CO prediction, especially at part-load operating conditions could be an issue for flamelet-based model: in fact, as the load decreases and the extinction limit approaches, a superequilibrium CO concentration, which cannot be accurately predicted by FGM, appears in the exhaust gases. To overcome this issue, a specific CO-burn-out model, following the original idea proposed by Klarmann, has been implemented in ANSYS fluent. The model allows to decouple the effective CO oxidation term from the one computed by FGM, defining a postflame zone where the source term of CO is treated following the Arrhenius formulation. In order to support the design process, an indepth CFD investigation has been carried out, evaluating the impact of an alternative burner geometrical configuration on stability and emissions and providing detailed information about the main regions and mechanisms of pollutants production. The outcomes support the analysis of experimental results, allowing an indepth investigation of the complex flow-field and the flame-related quantities, which have not been measured during the tests.

Numerical Investigations of Pollutant Emissions From Novel Heavy Duty Gas Turbine Burners Operated With Natural Gas

2019 ◽  
Author(s):  
Daniele Pampaloni ◽  
Pier Carlo Nassini ◽  
Antonio Andreini ◽  
Bruno Facchini ◽  
Matteo Cerutti
Keyword(s):  
Flow Field ◽  
Gas Turbine ◽  
Design Process ◽  
Gas Turbines ◽  
Operating Conditions ◽  
Pollutant Emissions ◽  
Formation Mechanisms ◽  
Heavy Duty ◽  
Heavy Duty Gas Turbine ◽  
Cost Efficient

Abstract A numerical investigation of pollutant emissions of a novel dry low-emissions burner for heavy-duty gas turbine applications is presented. The objective of the work is to develop and assess a robust and cost-efficient numerical setup for the prediction of NOx and CO emissions in industrial gas turbines and to investigate the pollutant formation mechanisms, thus supporting the design process of a novel low-emission burner. To this end, a comparison against experimental data, from a recent experimental campaign performed by BHGE in cooperation with University of Florence, has been exploited. In the first part of this work, a RANS approach on both a simplified geometry and the complete domain is adopted to characterize the global flame behavior and validate the numerical setup. Then, unsteady simulations exploiting the Scale Adaptive Simulation (SAS) approach have been performed to assess the prediction improvements that can be obtained with the unsteady modelling of the flame. For all simulations, the Flamelet Generated Manifold (FGM) model has been used, allowing the reliable and cost-efficient application of detailed chemistry mechanisms in CFD simulation. However, FGM typically faces issues predicting flame emissions, such as NOx and CO, due to the wide range of time scales involved, from turbulent mixing to pollutant species oxidation. Specific models are typically used to predict NOx emissions, starting from the converged flow field and introducing additional transport equations. Also CO prediction, especially at part-load operating conditions could be an issue for flamelet-based model: in fact, as the load decreases and the extinction limit approaches, a super-equilibrium CO concentration, which cannot be accurately predicted by FGM, appears in the exhaust gases. To overcome this issue, a specific CO burn-out model, following the original idea proposed by Klarmann, has been implemented in ANSYS Fluent. The model allows to decouple the effective CO oxidation term from the one computed by FGM, defining a post-flame zone where the source term of CO is treated following the Arrhenius formulation. In order to support the design process, an in-depth CFD investigation has been carried out, evaluating the impact of an alternative burner geometrical configuration on stability and emissions and providing detailed information about the main regions and mechanisms of pollutants production. The outcomes support the analysis of experimental results, allowing an in-depth investigation of the complex flow-field and the flame-related quantities, which have not been measured during the tests.

Computational Design and Experimental Evaluation of Using a Leading Edge Fillet on a Gas Turbine Vane

2001 ◽  
Author(s):  
G. A. Zess ◽  
K. A. Thole
Keyword(s):  
Boundary Layer ◽  
Flow Field ◽  
Pressure Gradient ◽  
Gas Turbine ◽  
Total Pressure ◽  
Guide Vane ◽  
Leading Edge ◽  
Field Measurements ◽  
Computational Design ◽  
Horseshoe Vortex

With the desire for increased power output for a gas turbine engine comes the continual push to achieve higher turbine inlet temperatures. Higher temperatures result in large thermal and mechanical stresses particularly along the nozzle guide vane. One critical region along a vane is the leading edge-endwall juncture. Based on the assumption that the approaching flow to this juncture is similar to a two-dimensional boundary layer, previous studies have shown that a horseshoe vortex forms. This vortex forms because of a radial total pressure gradient from the approaching boundary layer. This paper documents the computational design and experimental validation of a fillet placed at the leading edge-endwall juncture of a guide vane to eliminate the horseshoe vortex. The fillet design effectively accelerated the incoming boundary layer thereby mitigating the effect of the total pressure gradient. To verify the CFD studies used to design the leading edge fillet, flow field measurements were performed in a large-scale, linear, vane cascade. The flow field measurements were performed with a laser Doppler velocimeter in four planes orientated orthogonal to the vane. Good agreement between the CFD predictions and the experimental measurements verified the effectiveness of the leading edge fillet at eliminating the horseshoe vortex. The flowfield results showed that the turbulent kinetic energy levels were significantly reduced in the endwall region because of the absence of the unsteady horseshoe vortex.

Design Method for Subsonic and Transonic Cascade With Prescribed Mach Number Distribution

1992 ◽  
Vol 114 (3) ◽  
pp. 553-560 ◽  
Author(s):  
O. Le´onard ◽  
R. A. Van den Braembussche
Keyword(s):  
Mach Number ◽  
Flow Field ◽  
Pressure Distribution ◽  
Velocity Component ◽  
Design Method ◽  
Normal Velocity ◽  
Flow Solver ◽  
Number Distribution ◽  
Mach Number Distribution ◽  
Transonic Cascade

A iterative procedure for blade design, using a time marching procedure to solve the unsteady Euler equations in the blade-to-blade plane, is presented. A flow solver, which performs the analysis of the flow field for a given geometry, is transformed into a design method. This is done by replacing the classical slip condition (no normal velocity component) by other boundary conditions, in such a way that the required pressure or Mach number distribution may be imposed directly on the blade. The unknowns are calculated on the blade wall using the so-called compatibility relations. Since the blade shape is not compatible with the required pressure distribution, a nonzero velocity component normal to the blade wall evolves from the new flow calculation. The blade geometry is then modified by resetting the wall parallel to the new flow field, using a transpiration technique, and the procedure is repeated until the calculated pressure distribution has converged to the required one. Examples for both subsonic and transonic flows are presented and show a rapid convergence to the geometry required for the desired Mach number distribution. An important advantage of the present method is the possibility to use the same code for the design and the analysis of a blade.

scholarly journals A Different Approach to Gas Turbine Exhaust Silencing

1974 ◽  
Author(s):  
Marv Weiss
Keyword(s):  
Gas Turbine ◽  
Gas Turbines ◽  
Operating Conditions ◽  
Heavy Duty ◽  
Unique Method ◽  
Acoustic Testing ◽  
Gas Turbine Exhaust ◽  
Attenuation Values ◽  
Turbine Exhaust

A unique method for silencing heavy-duty gas turbines is described. The Switchback exhaust silencer which utilizes no conventional parallel baffles has at operating conditions measured attenuation values from 20 dB at 63 Hz to 45 dB at higher frequencies. Acoustic testing and analyses at both ambient and operating conditions are discussed.

Sign in / Sign up

Export Citation Format

Share Document