Prediction of Pressure Rise in a Gas Turbine Exhaust Duct Under Flameout Scenarios While Operating On Hydrogen and Natural Gas Blends

In recent years, there is a growing interest in blending hydrogen with natural gas fuels to produce low carbon electricity. It is important to evaluate the safety of gas turbine packages under these conditions, such as late-light off and flameout scenarios. However, the assessment of the safety risks by performing experiments in full-scale exhaust ducts is a very expensive and, potentially, risky endeavor. Computational simulations using a high fidelity CFD model provide a cost-effective way of assessing the safety risk. In this study, a computational model is implemented to perform three dimensional, compressible and unsteady simulations of reacting flows in a gas turbine exhaust duct. Computational results were validated against data obtained at the simulated conditions in a representative geometry. Due to the enormous size of the geometry, special attention was given to the discretization of the computational domain and the combustion model. Results show that CFD model predicts main features of the pressure rise driven by the combustion process. The peak pressures obtained computationally and experimentally differed in 20%. This difference increased up to 45% by reducing the preheated inflow conditions. The effects of rig geometry and flow conditions on the accuracy of the CFD model are discussed.

Analisis Pengaruh High Pressure Compressor Rotor Clearance Terhadap Exhaus Gas Temperature Margin pada CFM56-7

Exhaust Gas Temperatue is an parameter where the hot gases’s temperature leave the gas turbine. Exhaust gas temperature margin is the difference between highest temperature at take off phase with redline on indicator (???????????? ???????????????????????? °????=???????????? ????????????????????????????−???????????? ???????????????? ????????????). EGTM is one of any factor to determine engine performance. A good perfomance of an engine when it has a big margin (EGTM), during operation of an engine the EGTM could decrease untill 0 (zero). So many factors could affect EGTM deteroration there are: distress hardware such as airfoil erosion, leak of an airseals, and increase of clearance between tip balde and shroud. Increase of clearance happens in high pressure compressor rotor clearance. In CFM56-7 have 9 stage(s) of high pressure compressor and each stage give the EGT Loses. The calculation of EGT Effect/Losses is actual celarance – minimum clearance x 1000 x EGT Effect °C, where actual clearance define by the substraction of outside diameter’s rotor with inside diameter’s shroud, minimum clearance define in the manual, 1000 is adjustment from mils/microinch to inch, and EGT Effect is temperature that define in the manual. The analysist had done with 6 (six) engine serial number and proceed by corelation that shown linkage between clearance and EGT Effect, the corelation is strong shown the result of corelation (r) is 0.994275999 or nearest 1.

Prediction of Pressure Rise in a Gas Turbine Exhaust Duct Under Flameout Scenarios While Operating on Hydrogen and Natural Gas Blends

In recent years, there is a growing interest in blending hydrogen with natural gas fuels to produce low carbon electricity. It is important to evaluate the safety of gas turbine packages under these conditions, such as late-light off and flameout scenarios. However, the assessment of the safety risks by performing experiments in full-scale exhaust ducts is a very expensive and, potentially, risky endeavor. Computational simulations using a high fidelity CFD model provide a cost-effective way of assessing the safety risk. In this study, a computational model is implemented to perform three dimensional, compressible and unsteady simulations of reacting flows in a gas turbine exhaust duct. Computational results were validated against data obtained at the simulated conditions in a representative geometry. Due to the enormous size of the geometry, special attention was given to the discretization of the computational domain and the combustion model. Results show that CFD model predicts main features of the pressure rise driven by the combustion process. The peak pressures obtained computationally and experimentally differed in 20%. This difference increased up to 45% by reducing the preheated inflow conditions. The effects of rig geometry and flow conditions on the accuracy of the CFD model are discussed.

Effects of struts profiles and skewed angles on the aerodynamic performance of gas turbine exhaust diffuser

The strut structure directly affects the flow field characteristics and aerodynamic performance of the gas turbine exhaust diffuser. The effects of the strut profiles and strut skewed angles on the aerodynamic performance of the exhaust diffuser at different inlet pre-swirls were numerically investigated using three-dimensional Reynolds-Averaged Navier-Stokes(RANS) and Realizable k-ε turbulence model. The numerical static pressure recovery coefficient of the exhaust diffuser is in agreement with the experimental data well. The reliability of the numerical method for the exhaust diffuser performance analysis was demonstrated. Exhaust diffusers with four kinds of vertical strut profiles obtain the highest static pressure recovery coefficient at the inlet pre-swirl of 0.35. The similar static pressure recovery coefficient of exhaust diffusers with four kinds of vertical strut airfoils are observed when the inlet pre-swirl is less than 0.48. The static pressure recovery coefficient of exhaust diffusers with vertical b1 and b2 struts are higher than that with the a1 and a2 struts when the inlet pre-swirl is greater than 0.48. At the inlet pre-swirl of 0.35, The static pressure recovery coefficient of the exhaust diffuser with the a1 strut decreases with the increasing of the strut skewed angles. The static pressure recovery coefficient of the exhaust diffuser with the b1 strut increases with the increasing of the strut skewed angles, and the static pressure recovery coefficient increases by 3.6% compared with the vertical design when the skewed angle of b1 strut is 40[Formula: see text]. At the inlet pre-swirl of 0.64. The static pressure recovery coefficient of the exhaust diffuser with the a1 strut increases by 8.7% compared with the vertical design when the skewed angle of a1 strut is greater than 20°. In addition, the static pressure recovery coefficient of the exhaust diffuser with the b1 strut decreases by 3.8% compared with the vertical design when the skewed angle of b1 strut is 40°. The method to improve the aerodynamic performance of the exhaust diffuser by appropriate increase the strut maximum thickness and design the strut skewed angle is proposed in this work.

Theoretical study of the application of the outlet diffuser of a gas turbine as a steam circuit superheater of a combined gas-steam plant

Currently, thermal insulation of GTU output diffusers uses insulation of their inner surface. This is an expensive and complicated technological procedure. For gas turbines as part of CCGT, in order to reduce the cost of insulation and at the same time increase the useful power of the turbine, cooling the diffuser outer surface with a steam stream of a steam circuit can be an alternative way of internal insulation. Steam and gas parameters of a combined cycle plant with a CCGT-450T, as well as the results of experimental and computational studies of the GTU SGT5-3000E gas turbine exhaust channel model were used. The calculations of the efficiency of the surface cooling of the diffuser with the steam coming from the steam circuit were carried out using the analytical method. A scheme of a superheater located on the outer surface of the GTU outlet diffuser operating in a combined cycle is proposed. Analytic evaluation of its effectiveness showed that the surface area of the GTU diffuser of the type SGT5-3000E is sufficient to provide the necessary overheating of low-pressure steam. Installation of such a heat exchanger using the outer surface of the diffuser provides a decrease of the temperature of its outer wall from 537 to 200 оC. The study validity is confirmed by a patent for an invention. It has been established that the use of the outer surface of the GTU outlet diffuser instead of the heat exchange surface of the low pressure superheater of the utilizer boiler can be applied at CCGT unit to reduce heat and hydraulic losses in the diffuser path and in the utilizer boiler path.