A Numerical Study on Conjugate Heat Transfer for Supercritical CO2 Turbine Blade With Cooling Channels

2020 ◽  
Author(s):  
Akshay Khadse ◽  
Andres Curbelo ◽  
Ladislav Vesely ◽  
Jayanta S. Kapat
Keyword(s):  
Heat Transfer ◽  
Turbine Blade ◽  
Gas Turbines ◽  
Supercritical Co2 ◽  
Conjugate Heat Transfer ◽  
Maximum Temperature ◽  
Inlet Temperature ◽  
Cooling Channels ◽  
Blade Cooling ◽  
Turbine Inlet

Abstract The first stage of turbine in a Brayton cycle faces the maximum temperature in the cycle. This maximum temperature may exceed creep temperature limit or even melting temperature of the blade material. Therefore, it becomes an absolute necessity to implement blade cooling to prevent them from structural damage. Turbine inlet temperatures for oxy-combustion supercritical CO2 (sCO2) are promised to reach blade material limit in near future foreseeing need of turbine blade cooling. Properties of sCO2 and the cycle parameters can make Reynolds number external to blade and external heat transfer coefficient to be significantly higher than those typically experience in regular gas turbines. This necessitates evaluation and rethinking of the internal cooling techniques to be adopted. The purpose of this paper is to investigate conjugate heat transfer effects within a first stage vane cascade of a sCO2 turbine. This study can help understand cooling requirements which include mass flow rate of leakage coolant sCO2 and geometry of cooling channels. Estimations can also be made if the cooling channels alone are enough for blade cooling or there is need for more cooling techniques such as film cooling, impingement cooling and trailing edge cooling. The conjugate heat transfer and aerodynamic analysis of a turbine cascade is carried out using STAR CCM+. The turbine inlet temperature of 1350K and 1775 K is considered for the study considering future potential needs. Thermo-physical properties of this mixture are given as input to the code in form of tables using REFPROP database. The blade material considered is Inconel 718.

Conjugate Heat Transfer Simulation of the Intercooled Compressor Vanes Based on Discontinuous Galerkin Method

2016 ◽  
Author(s):  
Long-gang Liu ◽  
Chun-wei Gu ◽  
Xiao-dong Ren
Keyword(s):  
Heat Transfer ◽  
Discontinuous Galerkin ◽  
Gas Turbines ◽  
Conjugate Heat Transfer ◽  
Main Stream ◽  
Two Dimensional ◽  
Convective Cooling ◽  
Cooling Channels ◽  
Transfer Method ◽  
Aero Engines

Convective cooling channels are applied in a two-dimensional compressor vane to use the intercooling method to improve the efficiency of Brayton cycle and reduce the temperature of the vane. In this paper, we analyze the effect of coolant to the aerodynamic performance and heat transfer performance of the main stream and the vane. For the case of a two-dimensional compressor vane NACA65-(12A2I8b)10, the vane which has five convective cooling channels has been numerically simulated in different test conditions by discontinuous Galerkin (DG) method. The coolant is supercritical carbon dioxide whose pressure is 10MPa. Conjugate heat transfer method has been used in this paper. The numerical simulation result is similar to the experiment data and has been compared with the result of the vane without cooling channels to prove the effect of cooling channels. Cooling channels have large effect on the distribution of temperature and heat transfer coefficient. In addition, the relationship between Nu and Re on the fluid-solid interface has been analyzed and a suitable empirical equation has been obtained. This work analyzes the effect of intercooling system in the compressor and give several advice on future engineering applications in aero engines and gas turbines.

Topology Optimization of Serpentine Channels for Minimization of Pressure Loss and Maximization of Heat Transfer Performance As Applied for Additive Manufacturing

2019 ◽  
Author(s):  
Shinjan Ghosh ◽  
Jayanta S. Kapat
Keyword(s):  
Heat Transfer ◽  
Topology Optimization ◽  
Additive Manufacturing ◽  
Pressure Drop ◽  
Gas Turbine ◽  
Turbine Blades ◽  
Inlet Temperature ◽  
Internal Cooling ◽  
Cooling Channels ◽  
Blade Cooling

Abstract Gas Turbine blade cooling is an important topic of research, as a high turbine inlet temperature (TIT) essentially means an increase in efficiency of gas turbine cycles. Internal cooling channels in gas turbine blades are key to the cooling and prevention of thermal failure of the material. Serpentine channels are a common feature in internal blade cooling. Optimization methods are often employed in the design of blade internal cooling channels to improve heat-transfer and reduce pressure drop. Topology optimization uses a variable porosity approach to manipulate flow geometries by adding or removing material. Such a method has been employed in the current work to modify the geometric configuration of a serpentine channel to improve total heat transferred and reduce the pressure drop. An in-house OpenFOAM solver has been used to create non-traditional geometries from two generic designs. Geometry-1 is a 2-D serpentine passage with an inlet and 4 bleeding holes as outlets for ejection into the trailing edge. Geometry-2 is a 3-D serpentine passage with an aspect ratio of 3:1 and consists of two 180-degree bends. The inlet velocity for both the geometries was used as 20 m/s. The governing equations employ a “Brinkman porosity parameter” to account for the porous cells in the flow domain. Results have shown a change in shape of the channel walls to enhance heat-transfer in the passage. Additive manufacturing can be employed to make such unconventional shapes.

Heat transfer and friction in segmental turbine blade cooling channels

10.2514/3.925 ◽  
1997 ◽  
Vol 11 ◽  
pp. 486-488
Author(s):  
N. W. M. Ko ◽  
R. C. K. Leung ◽  
K. Lam ◽  
R. B. Spence ◽  
S. C. Lau
Keyword(s):  
Heat Transfer ◽  
Turbine Blade ◽  
Turbine Blade Cooling ◽  
Cooling Channels ◽  
Blade Cooling

Conjugate Heat Transfer Enhancement of an Internal Blade Pin-Finned Tip-Wall

2009 ◽  
Author(s):  
Gongnan Xie ◽  
Bengt Sunde´n
Keyword(s):  
Heat Transfer ◽  
Turbine Blade ◽  
Conjugate Heat Transfer ◽  
Gas Flow ◽  
Turbine Blades ◽  
Thermal Design ◽  
Inlet Temperature ◽  
Computational Domain ◽  
Pin Fins ◽  
Blade Tip

To improve gas turbine performance, the operating temperature has been increased continuously. However, the heat transferred to the turbine blade is substantially increased as the turbine inlet temperature is increased. Cooling methods are therefore needed for the turbine blades to ensure a long durability and safe operation. The blade tip region is exposed to the hot gas flow and is difficult to cool. A common way to cool the tip is to use serpentine passages with 180-deg turn under the blade tip-cap taking advantage of the three-dimensional turning effect and impingement. Increasing internal convective cooling is therefore required to increase the blade tip life. In this paper, augmented heat transfer of a blade tip with internal pin-fins has been investigated numerically using a conjugate heat transfer approach. The computational model consists of a two-pass channel with 180-deg turn and an array of pin-fins mounted on the tip-cap. The computational domain includes the fluid region and the solid pins as well as the solid tip regions. Turbulent convective heat transfer between the fluid and pins, and heat conduction within pins and tip are simultaneously computed. The inlet Reynolds numbers are ranging from 100,000 to 600,000. Details of the 3D fluid flow and heat transfer over the tip surface are presented. A comparison of the overall performance of the two models is presented. It is found that due to the combination of turning impingement and pin-fin cross flow, the heat transfer coefficient of the pin-finned tip is a factor of about 3.0 higher than that of a smooth tip. This augmentation is achieved at the cost of a pressure drop penalty of about 7%. With the conjugate heat transfer method, not only the simulated model is close to the experimental model, but also the distribution of the external tip heat transfer can be relevant for thermal design of turbine blade tips.

Research on Aerodynamic Characteristics of Air-Cooled Turbine Blade with Conjugate Heat Transfer Method

2013 ◽  
Vol 732-733 ◽  
pp. 270-275
Author(s):  
Jing Jing Zhang ◽  
Lian Fu Wang ◽  
Xiang Jun Fang
Keyword(s):  
Heat Transfer ◽  
Turbine Blade ◽  
Conjugate Heat Transfer ◽  
Air Flow ◽  
Aerodynamic Characteristics ◽  
Cooling Effect ◽  
Inlet Temperature ◽  
Turbine Inlet Temperature ◽  
Transfer Method ◽  
Aero Engines

In order to improve the performance of aero engines, trying to increase the turbine inlet temperature is an important way. But the turbine inlet temperature of modern aero engines can be more than 2000 K, which is far more than what the materials can bear. So advanced cooling technologies should be introduced to solve this problem. Using the conjugate heat transfer method, this paper researched the aerodynamic characteristics of a certain turbine blade with complex cooling structures. Some conclusions can be drawn: the velocity of the air flow and different distributions of coolant flow for turbine blade with multiple cooling air inlets have great influence on the cooling effect; the cooling effect decreases as the temperature ratio decreases; with the same mass cold gas, the less film cooling holes, the worse cooling effect; therefore, a reasonable air flow distribution plays an important role in obtaining good cooling effect.

Comparative Thermodynamic Analysis of Gas Turbine Systems with Turbine Blade Film Cooling

2012 ◽  
Vol 505 ◽  
pp. 539-543
Author(s):  
Kyoung Hoon Kim ◽  
Kyoung Jin Kim ◽  
Chul Ho Han
Keyword(s):  
Gas Turbine ◽  
Turbine Blade ◽  
Thermodynamic Analysis ◽  
Film Cooling ◽  
Pressure Ratio ◽  
Turbine Blades ◽  
Inlet Temperature ◽  
Turbine Inlet Temperature ◽  
Blade Cooling ◽  
Turbine Inlet

Since the gas turbine systems require active cooling to maintain high operating temperature while avoiding a reduction in the system operating life, turbine blade cooling is very important and essential but it may cause the performance losses in gas turbine. This paper deals with the comparative thermodynamic analysis of gas turbine system with and without regeneration by using the recently developed blade-cooling model when the turbine blades are cooled by the method of film cooling. Special attention is paid to investigating the effects of system parameters such as pressure ratio and turbine inlet temperature on the thermodynamic performance of the systems. In both systems the thermal efficiency increases with turbine inlet temperature, but its effect is less sensitive in simpler system

scholarly journals Optimum Power Boosting of Gas Turbine Cycles With Refrigerated Inlet Air and Compressor Intercooling

1996 ◽  
Author(s):  
Mohand A. Ait-Ali
Keyword(s):  
Gas Turbine ◽  
Gas Turbines ◽  
Pressure Ratio ◽  
Inlet Temperature ◽  
Turbine Blade Cooling ◽  
High Pressure Ratio ◽  
Blade Cooling ◽  
Air Inlet ◽  
Turbine Inlet ◽  
Compressor Work

With or without turbine blade cooling, gas turbine cycles have consistently higher turbine inlet temperatures than steam turbine cycles. But this advantage is more than offset by the excessive compressor work induced by warm inlet temperatures, particularly during operation on hot summer days. Instead of seeking still higher turbine inlet temperatures by means of sophisticated blade cooling technology and high temperature-resistant blade materials, it is proposed to greatly increase the cycle net work and also improve thermal efficiency by decreasing the compressor work. This is obtained by using refrigerated inlet air and compressor intercooling to an extent which optimizes the refrigerated air inlet temperature and consequently the gas turbine compression ratio with respect to maximum specific net power. The cost effectiveness of this conceptual cycle, which also includes regeneration, has not been examined in this paper as it requires unusually high pressure ratio gas turbines and compressors, as well as high volumetric air flow rate and low temperature refrigeration equipment for which reliable cost data is not easily available.

scholarly journals Comprehensive Review on Leading Edge Turbine Blade Cooling Technologies

2021 ◽  
Vol 39 (2) ◽  
pp. 403-416
Author(s):  
Chirag Sharma ◽  
Siddhant Kumar ◽  
Aanya Singh ◽  
Kartik R. Bhat Hire ◽  
Vedant Karnatak ◽  
...  
Keyword(s):  
Turbine Blade ◽  
Turbine Blades ◽  
Leading Edge ◽  
Inlet Temperature ◽  
Turbine Inlet Temperature ◽  
Entire Surface ◽  
Turbine Blade Cooling ◽  
Blade Cooling ◽  
Advantages And Disadvantages ◽  
Turbine Inlet

Developments in the gas turbine technology have caused widespread usage of the Turbomachines for power generation. With increase in the power demand and a drop in the availability of fuel, usage of turbines with higher efficiencies has become imperative. This is only possible with an increase in the turbine inlet temperature (TIT) of the gas. However, the higher limit of TIT is governed by the metallurgical boundary conditions set by the material used to manufacture the turbine blades. Hence, turbine blade cooling helps in drastically controlling the blade temperature of the turbine and allows a higher turbine inlet temperature. The blade could be cooled from the leading edge, from the entire surface of the blade or from the trailing edge. The various methods of blade cooling from leading edge and its comparative study were reviewed and summarized along with their advantages and disadvantages.

Sign in / Sign up

Export Citation Format

Share Document