Impact of Turbine-Strut Clocking on the Performance of a Turbine Center Frame

2020 ◽  
Author(s):  
P. Z. Sterzinger ◽  
F. Merli ◽  
A. Peters ◽  
S. Behre ◽  
F. Heitmeir ◽  
...  
Keyword(s):  
Flow Field ◽  
Numerical Data ◽  
Fast Response ◽  
Pressure Probe ◽  
Performance Impact ◽  
Aerodynamic Pressure ◽  
Carry Over ◽  
Vane Clocking ◽  
The Individual ◽  
The Impact

Abstract Previous studies have indicated a potential for improving the performance of a Turbine Center Frame (TCF) duct by optimizing the clocking position between the high-pressure-turbine (HPT) vanes and TCF struts. To assess the impact of clocking on the performance, a new test vehicle with a clockable ratio of HPT vanes to TCF struts, consisting of an HPT stage (aero-dynamically representative of the second-stage HPT engine), a TCF duct with non-turning struts, and a first-stage low-pressure turbine vane, was designed and tested in the transonic test turbine facility (TTTF) at Graz University of Technology. This paper quantifies the performance impact of clocking and describes the mechanisms causing TCF flow field changes, leveraging both experimental and numerical data. Other areas in the TCF duct impacted by the choice of the HPT vane circumferential position including the strength of unsteady HPT-TCF interaction modes, TCF strut incidence changes, and carry-over effects to the first LPT vane are additionally highlighted. Five-hole-probe (5HP) area traverses and kielhead-rake traverses were used to asses the flow field at the TCF-exit and calculate the pressure loss. The flow field at the TCF exit shows significant differences depending on the circumferential position of the HPT vane. A relative performance benefit of 5% was achieved. A series of unsteady RANS simulations were performed to support the measured results, understand and characterize the relevant loss mechanisms. The observed performance improvement was related to interaction between the HPT secondary -flow structures and the TCF struts. The impact of the HPT vane clocking on the unsteady flow field downstream of the TCF was investigated using Fast-Response Aerodynamic Pressure Probe (FRAPP) area traverses, analyzed by means of modal decomposition. In this way the individual azimuthal modes were ranked by their amplitude and a dependency of the clocking position was observed and quantified.

scholarly journals IMPACT OF TURBINE-STRUT CLOCKING ON THE PERFORMANCE OF A TURBINE CENTER FRAME

2021 ◽  
pp. 1-17
Author(s):  
Patrick Zeno Sterzinger ◽  
Filippo Merli ◽  
Andreas Peters ◽  
Stephan Behre ◽  
Franz Heitmeir ◽  
...  
Keyword(s):  
Flow Field ◽  
Numerical Data ◽  
Performance Impact ◽  
Test Vehicle ◽  
Low Pressure Turbine ◽  
Second Stage ◽  
University Of Technology ◽  
Turbine Vane ◽  
Carry Over ◽  
The Impact

Abstract Previous studies have indicated a potential for improving the performance of a Turbine Center Frame (TCF) duct by op- timizing the clocking position between the high-pressure-turbine (HPT) vanes and TCF struts. To assess the impact of clocking on the performance, a new test vehicle with a clockable ratio of HPT vanes to TCF struts, consisting of an HPT stage (aero- dynamically representative of the second-stage HPT engine), a TCF duct with non-turning struts, and a first-stage low-pressure turbine vane, was designed and tested in the transonic test tur- bine facility (TTTF) at Graz University of Technology. This paper quantifies the performance impact of clocking and describes the mechanisms causing TCF flow field changes, lever- aging both experimental and numerical data. Other areas in the TCF duct impacted by the choice of the HPT vane circumfer- ential position including the strength of unsteady HPT-TCF in- teraction modes, TCF strut incidence changes, and carry-over effects to the first LPT vane are additionally highlighted. Five-hole-probe (5HP) area traverses and kielhead-rake tra- verses were used to asses the flow field at the TCF-exit and calcu- late the pressure loss. The flow field at the TCF exit shows signif- icant differences depending on the circumferential position of the HPT vane. A relative performance benefit of 5% was achieved.

Three Dimensional Clocking Effects in a One and a Half Stage Transonic Turbine

2009 ◽  
Vol 132 (1) ◽  
Author(s):  
O. Schennach ◽  
J. Woisetschläger ◽  
B. Paradiso ◽  
G. Persico ◽  
P. Gaetani
Keyword(s):  
Flow Field ◽  
Three Dimensional ◽  
Fast Response ◽  
Secondary Flows ◽  
Pressure Probe ◽  
Time Resolved ◽  
Flow Angle ◽  
Aerodynamic Pressure ◽  
Velocity Flow ◽  
Transonic Turbine

This paper presents an experimental investigation of the flow field in a high-pressure transonic turbine with a downstream vane row (1.5 stage machine) concerning the airfoil indexing. The objective is a detailed analysis of the three-dimensional aerodynamics of the second vane for different clocking positions. To give an overview of the time-averaged flow field, five-hole probe measurements were performed upstream and downstream of the second stator. Furthermore in these planes additional unsteady measurements were carried out with laser Doppler velocimetry in order to record rotor phase-resolved velocity, flow angle, and turbulence distributions at two different clocking positions. In the planes upstream of the second vane, the time-resolved pressure field has been measured by means of a fast response aerodynamic pressure probe. This paper shows that the secondary flows of the second vane are significantly modified by the different clocking positions, in connection with the first vane modulation of the rotor secondary flows. An analysis of the performance of the second vane is also carried out, and a 0.6% variation in the second vane loss coefficient has been recorded among the different clocking positions.

Experimental Investigations of Clocking in a One and a Half Stage Transonic Turbine Using Laser-Doppler-Velocimetry and a Fast Response Aerodynamic Pressure Probe

2006 ◽  
Author(s):  
O. Schennach ◽  
J. Woisetschla¨ger ◽  
A. Fuchs ◽  
E. Go¨ttlich ◽  
A. Marn ◽  
...  
Keyword(s):  
Flow Field ◽  
Laser Doppler Velocimetry ◽  
Fast Response ◽  
Laser Doppler ◽  
Experimental Investigations ◽  
Pressure Probe ◽  
Doppler Velocimetry ◽  
Flow Angle ◽  
Aerodynamic Pressure ◽  
Transonic Turbine

The current paper presents experimental clocking investigations of the flow field in midspan in a high-pressure transonic turbine with a downstream vane row (1.5 stage machine). Laser-Doppler-Velocimetry measurements were carried out in order to record rotor phase resolved velocity, flow angle and turbulence distributions upstream and downstream of the second vane row at several different vane-vane positions. Additionally, a fast response aerodynamic pressure probe was used to get the total pressure distribution downstream of the second vane row for the same positions. Altogether, the measurements were performed for ten different 1st vane to 2nd vane positions (clocking positions) for measurements downstream of the 2nd vane row and two different clocking positions for measurements upstream of the 2nd vane row. The paper shows that different clocking positions have a significant influence on the flow field downstream of the 2nd vane row. Furthermore different measurement lines upstream of the 2nd vane row indicate that clocking has nearly no influence on the flow field close to the rotor exit.

Blade Row Interaction in a One and a Half Stage Transonic Turbine Focusing on Three Dimensional Effects: Part II—Clocking Effects

2008 ◽  
Author(s):  
O. Schennach ◽  
B. Paradiso ◽  
G. Persico ◽  
P. Gaetani ◽  
J. Woisetschla¨ger
Keyword(s):  
High Pressure ◽  
Flow Field ◽  
Three Dimensional ◽  
Field Measurements ◽  
Fast Response ◽  
Secondary Flows ◽  
Pressure Probe ◽  
Flow Angle ◽  
Aerodynamic Pressure ◽  
Transonic Turbine

The paper presents an experimental investigation of the flow field in a high-pressure transonic turbine with a downstream vane row (1.5 stage machine) concerning the airfoil indexing. The objective is a detailed analysis of the three dimensional flow field downstream of the high pressure turbine for different vane clocking positions. To give an overview of the time averaged flow field, measurements by means of a pneumatic five hole probe were performed upstream and downstream of the second stator. Furthermore in this planes additional unsteady measurements were carried out with Laser Doppler Velocimetry in order to record rotor phase resolved velocity, flow angle and turbulence distributions at two different clocking positions. In the measurement plane upstream the second vane the time resolved pressure field has been analyzed by means of a Fast Response Aerodynamic Pressure Probe. The paper shows that the secondary flows of the second vane are significantly modified for different clocking positions, in connection with the first vane modulation of the rotor secondary flows. An analysis of the performance of the second vane is also carried out.

Unsteady Flow Interactions Between a High- and Low-Pressure Turbine: Part 2 — Rotor-Synchronic Averaging and Proper Orthogonal Decomposition of the Unsteady Flow Fields

2019 ◽  
Author(s):  
M. Dellacasagrande ◽  
P. Z. Sterzinger ◽  
S. Zerobin ◽  
F. Merli ◽  
L. Wiesinger ◽  
...  
Keyword(s):  
Flow Field ◽  
Unsteady Flow ◽  
Proper Orthogonal Decomposition ◽  
Low Pressure ◽  
Fast Response ◽  
Orthogonal Decomposition ◽  
Pressure Probe ◽  
Low Pressure Turbine ◽  
Aerodynamic Pressure ◽  
Proper Orthogonal

Abstract This paper, the second of two parts, presents an experimental investigation of the unsteady flow field evolving in a two-stage two-spool test turbine facility. The experimental setup, which was designed to reproduce the operating condition of modern commercial aero-engines, consists of a high-pressure turbine (HPT) stage followed by a turbine center frame (TCF) with non-turning struts, and a co-rotating low-pressure turbine (LPT) stage. Measurements carried out with a fast-response aerodynamic pressure probe (FRAPP) were post-processed to describe the unsteady evolution of the flow downstream of the HPT rotor, through the TCF duct, and at the exit of the LPT stage. The time-resolved results presented in the first part of this paper show that deterministic fluctuations due to both rotors characterize the flow field downstream of the LPT. In order to characterize the deterministic unsteadiness induced by all the components constituting the turbine facility (HPT, TCF and LPT) and their interactions, measurements were carried out in three different planes located downstream of the HPT, at the exit of the TCF and downstream of the LPT stage. The unsteady results obtained in the plane located at the exit of the LPT are discussed in more details in this second part of this paper, providing information about the interactions between the two rotors. A proper phase-average procedure, known as rotor synchronic averaging (RSA), which takes into account the rotorrotor interaction, was adopted to capture the unsteadiness due to both rotors. Proper Orthogonal Decomposition (POD) was also applied to provide a characterization of the major contributors in terms of energy to the deterministic unsteadiness occurring in the test turbine facility. At the exit of the LPT rotor, the perturbations induced by the HPT stage and the interactions between the two rotors were found to dominate over the unsteadiness due to the LPT only.

Experimental Investigation of the Unsteady Flow Field Downstream of a Counter-Rotating Two-Spool Turbine Rig

2012 ◽  
Author(s):  
Davide Lengani ◽  
Cornelia Santner ◽  
Rosario Spataro ◽  
Berardo Paradiso ◽  
Emil Göttlich
Keyword(s):  
Experimental Investigation ◽  
Flow Field ◽  
Unsteady Flow ◽  
Fast Response ◽  
Secondary Flows ◽  
Operating Conditions ◽  
Pressure Probe ◽  
Time Resolved ◽  
Flow Angle ◽  
Aerodynamic Pressure

The paper presents an experimental investigation of the unsteady flow field in the two-spool counter-rotating transonic turbine at Graz University of Technology. The test setup consists of a high pressure (HP) stage, a diffusing mid turbine frame with turning struts (TMTF) and a shrouded low pressure (LP) rotor. The two rotors are mounted on mechanically independent shafts in order to provide engine-representative operating conditions. The rig was designed in cooperation with MTU Aero Engines and Volvo Aero within the EU project DREAM (ValiDation of Radical Engine Architecture SysteMs). A two-sensor fast response aerodynamic pressure probe (2S-FRAP) has been employed to provide time-resolved aerodynamic area traverses downstream of the LP turbine. Such measurement allows estimating the total deterministic unsteadiness transported through the duct. In particular, it has been possible to isolate the structures induced by each rotor by means of the encoders mounted on the two shafts. A global ensemble averaged field, which takes into account the rotor-rotor interactions, is also provided. The time resolved distributions of the flow quantities are then discussed in details. The perturbations due to the HP rotor in terms of velocity and flow angle are negligible in this downstream plane. Indeed, the largest fluctuations of velocity are due to the TMTF-LP rotor interaction, they occur in the wake and secondary flows of the TMTF. Large fluctuations of static and total pressure are instead due to both rotors to the same extent.

Experimental Investigations of Clocking in a One-and-a-Half-Stage Transonic Turbine Using Laser Doppler Velocimetry and a Fast Response Aerodynamic Pressure Probe

2006 ◽  
Vol 129 (2) ◽  
pp. 372-381 ◽  
Author(s):  
O. Schennach ◽  
J. Woisetschläger ◽  
A. Fuchs ◽  
E. Göttlich ◽  
A. Marn ◽  
...  
Keyword(s):  
Flow Field ◽  
Laser Doppler Velocimetry ◽  
Fast Response ◽  
Laser Doppler ◽  
Experimental Investigations ◽  
Pressure Probe ◽  
Doppler Velocimetry ◽  
Flow Angle ◽  
Aerodynamic Pressure ◽  
Transonic Turbine

The current paper presents experimental clocking investigations of the flow field in midspan in a high-pressure transonic turbine with a downstream vane row (1.5 stage machine). Laser-Doppler-velocimetry measurements were carried out in order to record rotor phase resolved velocity, flow angle, and turbulence distributions upstream and downstream of the second vane row at several different vane-vane positions. Additionally, a fast-response aerodynamic pressure probe was used to get the total pressure distribution downstream of the second vane row for the same positions. Altogether, the measurements were performed for ten different first vane to second vane positions (clocking positions) for measurements downstream of the second vane row and two different clocking positions for measurements upstream of the second vane row. The paper shows that different clocking positions have a significant influence on the flow field downstream of the second vane row. Furthermore, different measurement lines upstream of the second vane row indicate that clocking has nearly no influence on the flow field close to the rotor exit.

Unsteady Effects due to Rotor Purge Flow Variations in a Dual-Spool Turbine Setup

2020 ◽  
Author(s):  
F. Merli ◽  
P. Z. Sterzinger ◽  
M. Dellacasagrande ◽  
L. Wiesinger ◽  
A. Peters ◽  
...  
Keyword(s):  
Flow Field ◽  
Gas Turbines ◽  
Pressure Probe ◽  
Wall Region ◽  
Two Stage ◽  
Reference Case ◽  
Time Resolved ◽  
Aerodynamic Pressure ◽  
Purge Flow ◽  
The Impact

Abstract The paper discusses the impact of rotor purge flows on the unsteady flow field downstream of a two-stage, two-spool test turbine. The analyzed setup is representative of the second high-pressure turbine (HPT) and the first low-pressure turbine (LPT) stage in a modern turbofan aero-engine, with a turbine center frame (TCF) with non-turning struts in-between the two turbines. All measurements were carried out for an engine-representative test vehicle setup at the Transonic Test Turbine Facility at Graz University of Technology. The test rig features a secondary air system delivering five purge flows with independent temperature and mass flow control to the HPT and LPT cavities. This work extends the results shown in two recent publications analyzing the time-resolved flow through the same two-stage setup at fixed purge flow rates. The paper aims to provide additional input about the driving sources of unsteadiness in gas turbines for aeronautic applications, by isolating the HPT and LPT purge air contributions. The time-resolved flow field at the LPT exit was acquired with a Fast Response Aerodynamic Pressure Probe (FRAPP) for three different purge conditions (reference case, no HPT purge case, no LPT purge case), to separate and quantify the impact of HPT and LPT purge contributions on the main flow field. The so-called Rotor Synchronic Averaging (RSA) technique was used as phase-averaging approach, to account for the unsteadiness due to both rotors. Proper Orthogonal Decomposition (POD) was then applied to isolate the most important structures and identify their origins. The comparison of the three data-sets shows a significant influence of the HPT purge on the entire flow field at the LPT exit, even though the HPT is located far upstream, while the LPT purge impact appears to mostly affect the end-wall region.

scholarly journals Spatial and temporal resolution of a fast-response aerodynamic pressure probe in grid-generated turbulence

2021 ◽  
Vol 62 (2) ◽  
Author(s):  
Florian M. Heckmeier ◽  
Stefan Hayböck ◽  
Christian Breitsamter
Keyword(s):  
Temporal Resolution ◽  
Pressure Sensors ◽  
Mesh Size ◽  
Reynolds Numbers ◽  
Fast Response ◽  
Pressure Probe ◽  
Aerodynamic Pressure ◽  
Kolmogorov Length Scale ◽  
High Bandwidth ◽  
Velocity Spectra

Abstract The spatial and temporal resolution of a fast-response aerodynamic pressure probe (FRAP) is investigated in a benchmark flow of grid-generated turbulence. A grid with a mesh size of $$M=6.4$$ M = 6.4 mm is tested for two different free-stream velocities, hence, resulting in Reynolds numbers of $$Re_M= \{4300,12800\}$$ R e M = { 4300 , 12800 } . A thorough analysis of the applicability of the underlying assumptions with regard to turbulence isotropy and homogeneity is carried out. Taylor’s frozen turbulence hypothesis is assumed for the calculation of deducible flow quantities, like the turbulent kinetic energy or the dissipation rate. Furthermore, besides the examination of statistical quantities, velocity spectra of measurements downstream of the grid are quantified. Results of a small fast-response five-hole pressure probe equipped with piezo-resistive differential pressure sensors are compared to single-wire hot-wire constant temperature anemometry data for two different wire lengths. Estimates of temporal and spatial turbulent scales (e.g., Taylor micro scale and Kolmogorov length scale) show good agreement to data in the literature but are affected by filtering effects. Especially in the energy spectra, very high bandwidth content cannot be resolved by the FRAP, which is mainly due to bandwidth limits in the temporal calibration of the FRAP and the minimal resolution of the integrated sensors. Graphic abstract

Uncertainty Evaluation on Multi-Hole Aerodynamic Pressure Probes

2020 ◽  
Author(s):  
Andrea Notaristefano ◽  
Paolo Gaetani ◽  
Vincenzo Dossena ◽  
Alberto Fusetti
Keyword(s):  
Uncertainty Analysis ◽  
Evaluation Method ◽  
Experimental Testing ◽  
Uncertainty Propagation ◽  
Calibration Procedure ◽  
Fast Response ◽  
Uncertainty Evaluation ◽  
Sensor Calibration ◽  
Pressure Probe ◽  
Aerodynamic Pressure

Abstract In the frame of a continuous improvement of the performance and accuracy in the experimental testing of turbomachines, the uncertainty analysis on measurements instrumentation and techniques is of paramount importance. For this reason, since the beginning of the experimental activities at the Laboratory of Fluid Machines (LFM) located at Politecnico di Milano (Italy), this issue has been addressed and different methodologies have been applied. This paper proposes a comparison of the results collected applying two methods for the measurement uncertainty quantification to two different aerodynamic pressure probes: sensor calibration, aerodynamic calibration and probe application are considered. The first uncertainty evaluation method is the so called “Uncertainty Propagation” method (UPM); the second is based on the “Monte Carlo” method (MCM). Two miniaturized pressure probes have been selected for this investigation: a pneumatic 5-hole probe and a spherical fast response aerodynamic pressure probe (sFRAPP), the latter applied as a virtual 4-hole probe. Since the sFRAPP is equipped with two miniaturized pressure transducers installed inside the probe head, a specific calibration procedure and a dedicated uncertainty analysis are required.

Sign in / Sign up

Export Citation Format

Share Document