Simulation of Acoustic Streaming in a Resonator

2004 ◽  
Author(s):  
Bakhtier Farouk ◽  
Murat K. Aktas
Keyword(s):  
Flow Field ◽  
Standing Wave ◽  
Oscillatory Flow ◽  
Stokes Equations ◽  
Acoustic Streaming ◽  
Flow Patterns ◽  
Vortical Flow ◽  
Navier Stokes ◽  
Navier Stokes Equations ◽  
Streaming Flow

Formation of vortical flow structures in a rectangular enclosure due to acoustic streaming is investigated numerically. The oscillatory flow field in the enclosure is created by the vibration of a vertical side wall of the enclosure. The frequency of the wall vibration is chosen such that a standing wave forms in the enclosure. The interaction of this standing wave with the horizontal solid walls leads to the production of Rayleigh type acoustic streaming flow patterns in the enclosure. All four walls of the enclosure considered are thermally insulated. The fully compressible form of the Navier-Stokes equations is considered and an explicit time-marching algorithm is used to explicitly track the acoustic waves. Numerical solutions are obtained by employing a highly accurate flux corrected transport (FCT) algorithm for the convection terms. A time-splitting technique is used to couple the viscous and diffusion terms of the full Navier-Stokes equations. Non-uniform grid structure is employed in the computations. The simulation of the primary oscillatory flow and the secondary (steady) streaming flows in the enclosure is performed. Streaming flow patterns are obtained by time averaging the primary oscillatory flow velocity distributions. The effect of the amount of wall displacement on the formation of the oscillatory flow field and the streaming structures are studied. Computations indicate that the nonlinearity of the acoustic field increases with increasing amount of the vibration amplitude. The form and the strength of the secondary flow associated with the oscillatory flow field and viscous effects are found to be strongly correlated to the maximum displacement of the vibrating wall. Total number of acoustic streaming cells per wavelength is also determined by the strength and the level of the nonlinearity of the sound field in the resonator.

Influences of Recess Geometry and Restrictor Dimension on Flow Patterns and Pressure Distribution of Hydrostatic Bearings

2007 ◽  
Author(s):  
Cheng-Hsien Chen ◽  
Yuan Kang ◽  
Yeon-Pun Chang ◽  
De-Xing Peng ◽  
Ding-Wen Yang
Keyword(s):  
Pressure Distribution ◽  
Stokes Equations ◽  
Flow Patterns ◽  
Lubricant Film ◽  
Navier Stokes ◽  
Width Ratio ◽  
Navier Stokes Equations ◽  
Hydrostatic Bearing ◽  
Lubricant Flow ◽  
Land Width

This paper studies the influences of recess geometry and restrictor dimensions on the flow patterns and pressure distribution of lubricant film, which are coupled effects of hybrid characteristics of a hydrostatic bearing. The lubricant flow is described by using the Navier-Stokes equations. The Galerkin weighted residual finite element method is applied to determine the lubricant velocities and pressure in the bearing clearance. The numerical simulations will evaluate the effects of the land-width ratio and restriction parameter as well as the influence of modified Reynolds number and the jet-strength coefficient on the flow patterns in the recess and pressure distribution in lubricant film. On the basis of the simulation drawn from this study, the simulated results are expected to help engineers make better use of the design of hydrostatic bearing and its restrictors.

On the Flow Fields of Inertial Impactors

1974 ◽  
Vol 96 (4) ◽  
pp. 394-400 ◽  
Author(s):  
V. A. Marple ◽  
B. Y. H. Liu ◽  
K. T. Whitby
Keyword(s):  
Flow Field ◽  
Stokes Equations ◽  
Relaxation Method ◽  
Water Model ◽  
Navier Stokes ◽  
Visualization Technique ◽  
Navier Stokes Equations ◽  
Theoretical Results ◽  
Plate Distance ◽  
Good Agreement

The flow field in an inertial impactor was studied experimentally with a water model by means of a flow visualization technique. The influence of such parameters as Reynolds number and jet-to-plate distance on the flow field was determined. The Navier-Stokes equations describing the laminar flow field in the impactor were solved numerically by means of a finite difference relaxation method. The theoretical results were found to be in good agreement with the empirical observations made with the water model.

Fluid flow over and through a regular bundle of rigid fibres

2016 ◽  
Vol 792 ◽  
pp. 5-35 ◽  
Author(s):  
Giuseppe A. Zampogna ◽  
Alessandro Bottaro
Keyword(s):  
Porous Medium ◽  
Fluid Flow ◽  
Flow Field ◽  
Stokes Equations ◽  
Transversely Isotropic ◽  
Navier Stokes ◽  
Leading Order ◽  
Macroscopic Scale ◽  
Navier Stokes Equations ◽  
Homogenized Model

The interaction between a fluid flow and a transversely isotropic porous medium is described. A homogenized model is used to treat the flow field in the porous region, and different interface conditions, needed to match solutions at the boundary between the pure fluid and the porous regions, are evaluated. Two problems in different flow regimes (laminar and turbulent) are considered to validate the system, which includes inertia in the leading-order equations for the permeability tensor through a Oseen approximation. The components of the permeability, which characterize microscopically the porous medium and determine the flow field at the macroscopic scale, are reasonably well estimated by the theory, both in the laminar and the turbulent case. This is demonstrated by comparing the model’s results to both experimental measurements and direct numerical simulations of the Navier–Stokes equations which resolve the flow also through the pores of the medium.

Numerical Investigations for the Effect of Slender Body on Dynamic Rolling Characteristics of a 80°/60° Double Delta Wing

2013 ◽  
Vol 444-445 ◽  
pp. 286-292
Author(s):  
Bing Han ◽  
Min Xu ◽  
Xi Pei ◽  
Xiao Min An
Keyword(s):  
Stokes Equations ◽  
Delta Wing ◽  
Time Lag ◽  
Slender Body ◽  
Vortical Flow ◽  
Navier Stokes ◽  
Rolling Motion ◽  
Navier Stokes Equations ◽  
Lag Effect ◽  
Double Delta Wing

The effect of slender body on the rolling characteristics of a double delta wing is found by comparing the numerical simulation results of the double delta wing and wing-body configuration. The coupled computation system solving the Navier-Stokes equations and the rolling motion equation alternatively to obtain the unsteady vortical flow around the two configurations while rolling. The results conclusively showed the upwash effect of the slender body enhanced the energy of strake vortex and merged vortex.The aerodynamic lag of double delta wing is weak, contrarily, the time lag effect of the wing-body configuration is significant. The asymmetry vortices structure nearby the trailing edge are believed to be the main reason for the unsteady time lag effect.

CFD in the Loop: Ensemble Kalman Filtering With Underwater Mobile Sensor Networks

2014 ◽  
Author(s):  
Axel Hackbarth ◽  
Edwin Kreuzer ◽  
Thorben Schröder
Keyword(s):  
Flow Field ◽  
Stokes Equations ◽  
Fluid Dynamic ◽  
Navier Stokes ◽  
Mobile Sensor ◽  
Dynamic Simulations ◽  
Navier Stokes Equations ◽  
Time Flow ◽  
Strong Current ◽  
Predictive Controller

In marine environments, sparse in-situ measurements can be used for the estimation of the fluid dynamic field. To make best use of a mobile sensor network in an environment whose dynamics can be described by the Navier-Stokes equations, we developed a framework for data assimilation with motion-constrained underwater vehicles, that takes the physical field properties into account while sampling. Our algorithm uses an ensemble Kalman filter that propagates hundreds of slightly varied coarse fluid dynamic simulations through time. Flow and scalar measurements from the mobile sensors are integrated into all ensemble members. We implemented a model predictive controller to calculate covariance minimizing paths from the estimated flow field and motion primitives of the vehicles, which are affected by a strong current. Thereby, we were able to indirectly track dynamically changing wall temperatures through measurements of flow field variables.

Mathematical and Physical Modeling of Three-Phase Gas-Stirred Ladles

2016 ◽  
Vol 1812 ◽  
pp. 29-34
Author(s):  
Juan A. López ◽  
Marco A. Ramírez-Argáez ◽  
Adrián M. Amaro-Villeda ◽  
Carlos González
Keyword(s):  
Mathematical Model ◽  
Physical Model ◽  
Stokes Equations ◽  
Steel Slag ◽  
Flow Patterns ◽  
Navier Stokes ◽  
Steel Ladle ◽  
Phase System ◽  
Navier Stokes Equations ◽  
Three Phase

ABSTRACTA very realistic 1:17 scale physical model of a 140-ton gas-stirred industrial steel ladle was used to evaluate flow patterns measured by Particle Image Velocimetry (PIV), considering a three-phase system (air-water-oil) to simulate the argon-steel-slag system and to quantify the effect of the slag layer on the flow patterns. The flow patterns were evaluated for a single injector located at the center of the ladle bottom with a gas flow rate of 2.85 l/min, with the presence of a slag phase with a thickness of 0.0066 m. The experimental results obtained in this work are in excellent agreement with the trends reported in the literature for these gas-stirred ladles. Additionally, a mathematical model was developed in a 2D gas-stirred ladle considering the three-phase system built in the physical model. The model was based on the Eulerian approach in which the continuity and the Navier Stokes equations are solved for each phase. Therefore, there were three continuity and six Navier-Stokes equations in the system. Additionally, turbulence in the ladle was computed by using the standard k-epsilon turbulent model. The agreement between numerical simulations and experiments was excellent with respect to velocity fields and turbulent structure, which sets the basis for future works on process analysis with the developed mathematical model, since there are only a few three-phase models reported so far in the literature to predict fluid dynamics in gas-stirred steel ladles.

scholarly journals Numerical and Experimental Investigation of a Supersonic Flow Field around Solid Fuel on an Inclined Flat Plate

2009 ◽  
Vol 2009 ◽  
pp. 1-10 ◽  
Author(s):  
Uzu-Kuei Hsu
Keyword(s):  
Flow Field ◽  
Solid Fuel ◽  
Stokes Equations ◽  
Control Volume ◽  
Navier Stokes ◽  
Navier Stokes Equations ◽  
Short Period ◽  
Volume Method ◽  
Environmental Temperatures ◽  
Gasification Temperature

This research adopts a shock tube 16 meters long and with a 9 cm bore to create a supersonic, high-temperature, and high-pressure flowfield to observe the gasification and ignition of HTPB solid fuel under different environments. Also, full-scale 3D numerical simulation is executed to enhance the comprehension of this complex phenomenon. The CFD (Computational Fluid Dynamics) code is based on the control volume method and the pre-conditioning method for solving the Navier-Stokes equations to simulate the compressible and incompressible coupling problem. In the tests, a HTPB slab is placed in the windowed-test section. Various test conditions generate different supersonic Mach numbers and environmental temperatures. In addition, the incident angles of the HTPB slab were changed relative to the incoming shock wave. Results show that as the Mach number around the slab section exceeded 1.25, the flowfield temperature achieved 1100 K, which is higher than the HTPB gasification temperature (930 K~1090 K). Then, gasification occurred and a short-period ignition could be observed. In particular, when the slab angle was7∘, the phenomenon became more visible. This is due to the flow field temperature increase when the slab angle was at7∘.

scholarly journals Numerical and Analytical Study of Fluid Dynamic Forces in Seals and Bearings

1988 ◽  
Vol 110 (3) ◽  
pp. 315-325 ◽  
Author(s):  
L. T. Tam ◽  
A. J. Przekwas ◽  
A. Muszynska ◽  
R. C. Hendricks ◽  
M. J. Braun ◽  
...  
Keyword(s):  
Flow Field ◽  
Stokes Equations ◽  
Fluid Dynamic ◽  
Three Dimensional ◽  
Circumferential Velocity ◽  
Navier Stokes ◽  
Navier Stokes Equations ◽  
Lumped Model ◽  
Destabilizing Factors ◽  
Recirculation Zones

A numerical model based on a transformed, conservative form of the three-dimensional Navier-Stokes equations and an analytical model based on “lumped” fluid parameters are presented and compared with studies of modeled rotor/bearing/seal systems. The rotor destabilizing factors are related to the rotative character of the flow field. It is shown that these destabilizing factors can be reduced through a descrease in the fluid average circumferential velocity. However, the rotative character of the flow field is a complex three-dimensional system with bifurcated secondary flow patterns that significantly alter the fluid circumferential velocity. By transforming the Navier-Stokes equations to those for a rotating observer and using the numerical code PHOENICS-84 with a nonorthogonal body fitted grid, several numerical experiments were carried out to demonstrate the character of this complex flow field. In general, fluid injection and/or preswirl of the flow field opposing the shaft rotation significantly intensified these secondary recirculation zones and thus reduced the average circumferential velocity, while injection or preswirl in the direction of rotation significantly weakened these zones. A decrease in average circumferential velocity was related to an increase in the strength of the recirculation zones and thereby promoted stability. The influence of the axial flow was analyzed. The lumped model of fluid dynamic force based on the average circumferential velocity ratio (as opposed to the bearing/seal coefficient model) well described the obtained results for relatively large but limited ranges of parameters. This lumped model is extremely useful in rotor/bearing/seal system dynamic analysis and should be widely recommended. Fluid dynamic forces and leakage rates were calculated and compared with seal data where the working fluid was bromotrifluoromethane (CBrF3). The radial and tangential force predictions were in reasonable agreement with selected experimental data. Nonsynchronous perturbation provided meaningful information for system lumped parameter identification from numerical experiment data.

scholarly journals Calculating Rotordynamic Coefficients of Seals by Finite-Difference Techniques

1987 ◽  
Vol 109 (3) ◽  
pp. 388-394 ◽  
Author(s):  
F. J. Dietzen ◽  
R. Nordmann
Keyword(s):  
Finite Difference ◽  
Finite Difference Method ◽  
Flow Field ◽  
Pressure Distribution ◽  
Difference Method ◽  
Stokes Equations ◽  
Navier Stokes ◽  
Navier Stokes Equations ◽  
Rotordynamic Coefficients ◽  
Finite Difference Techniques

For modelling the turbulent flow in a seal the Navier-Stokes equations in connection with a turbulence model (k-ε-model) are solved by a finite-difference method. A motion of the shaft around the centered position is assumed. After calculating the corresponding flow field and the pressure distribution, the rotordynamic coefficients of the seal can be determined. These coefficients are compared with results obtained by using the bulk flow theory of Childs [1] and with experimental results.

Sign in / Sign up

Export Citation Format

Share Document