Large Eddy Simulation of Heat Transfer Over In-Line Flat-Tube Array in Laminar and Turbulent Flows

2017 ◽  
Author(s):  
Salar Taghizadeh ◽  
Sumanta Acharya ◽  
Kong Ling ◽  
Yousef Kanani ◽  
Xuan Ge
Keyword(s):  
Heat Transfer ◽  
Large Eddy Simulation ◽  
Turbulent Flows ◽  
Numerical Study ◽  
Numerical Models ◽  
Leading Edge ◽  
Flat Tube ◽  
Eddy Simulation ◽  
Wide Range ◽  
Large Eddy

This study presents a transient three-dimensional numerical study on fluid flow and heat transfer of flat-tube array using large eddy simulation (LES) covering both laminar and turbulent flow regimes. The simulations were performed in a rectangular region containing only one tube with periodic conditions specified on all boundaries. A staggered flat-plate array was first studied, and an existing solution was used for validation purpose. The numerical models were then applied to an in-line array composed of flat tubes with an aspect ratio of 0.25 and fixed tube spacings. By varying the in-flow velocity, the tube array was studied over a wide range of Reynolds number (600–12000). Temperature, velocity, and turbulent kinetic energy distributions as well as the interactions between them are presented and analyzed. Furthermore, the local heat transfer rate was analyzed along the various parts of the tube (leading edge, flat-top and wake or trailing-edge regions). Heat transfer correlation for each region of the tube and the entire tube array is proposed.

Interactions of Separation Bubble With Oncoming Wakes by Large-Eddy Simulation

2015 ◽  
Vol 138 (2) ◽  
Author(s):  
S. Sarkar ◽  
Harish Babu ◽  
Jasim Sadique
Keyword(s):  
Heat Transfer ◽  
Boundary Layer ◽  
Large Eddy Simulation ◽  
Separation Bubble ◽  
Leading Edge ◽  
Constant Thickness ◽  
Eddy Simulation ◽  
Large Eddy ◽  
Flow Past A Cylinder ◽  
Rotor Stator Interaction

The unsteady flow physics and heat transfer characteristics due to interactions of periodic passing wakes with a separated boundary layer are studied using large-eddy simulation (LES). A series of airfoils of constant thickness with rounded leading edge are employed to obtain the separated boundary layer. Wake data extracted from precursor LES of flow past a cylinder are used to replicate a moving bar that generates wakes in front of a cascade (in this case, an infinite row of the model airfoils). This setup is a simplified representation of the rotor–stator interaction in turbomachinery. With a uniform inlet, the laminar boundary layer separates near the leading edge, undergoes transition due to amplification of disturbances, becomes turbulent, and finally reattaches forming a separation bubble. In the presence of oncoming wakes, the characteristics of the separated boundary layer have changed and the impinging wakes are found to be the mechanism affecting the reattachment. Phase-averaged results illustrate the periodic behavior of both flow and heat transfer. Large undulations in the phase-averaged skin friction and Nusselt number distributions can be attributed to the excitation of the boundary layer by convective wakes forming coherent vortices, which are being shed and convect downstream. Further, the transition of the separated boundary layer during the wake-induced path is governed by a mechanism that involves the convection of these vortices followed by increased fluctuations, where viscous effect is substantial.

scholarly journals Statistical Analysis of Dynamic Subgrid Modeling Approaches in Large Eddy Simulation

2021 ◽  
Author(s):  
Mohammad Khalid Hossen ◽  
Asokan Mulayath Variyath ◽  
Jahrul M Alam
Keyword(s):  
Kinetic Energy ◽  
Large Eddy Simulation ◽  
Turbulent Flows ◽  
Large Scale ◽  
Physical Space ◽  
Statistical Characteristics ◽  
Small Scale ◽  
Eddy Simulation ◽  
Wide Range ◽  
Large Eddy

In large eddy simulation (LES) of turbulent flows, the most critical dynamical processes to be considered by dynamic subgrid models to account for an average cascade of kinetic energy from the largest to the smallest scales of the flow is not fully clear. Furthermore, evidence of vortex stretching being the primary mechanism of the cascade is not out of the question. In this article, we study some essential statistical characteristics of vortex stretching and its role in dynamic approaches of modeling subgrid-scale turbulence. We have compared the interaction of subgrid stresses with the filtered quantities among four models using invariants of the velocity gradient tensor. This technique is a single unified approach to studying a wide range of length scales in the turbulent flow. In addition, it also provides a rational basis for the statistical characteristics a subgrid model must serve in physical space to ensure an appropriate cascade of kinetic energy. Results indicate that the stretching mechanism extracts energy from the large-scale straining motion and passes it onto small-scale stretched vortices.

Large Eddy Simulation of a Controlled-Diffusion Cascade Blade at Varying Flow Inlet Angles

2009 ◽  
Author(s):  
W. Andrew McMullan ◽  
Gary J. Page
Keyword(s):  
Boundary Layer ◽  
Large Eddy Simulation ◽  
Leading Edge ◽  
Fine Grid ◽  
Controlled Diffusion ◽  
Eddy Simulation ◽  
Pressure Distributions ◽  
Wide Range ◽  
Large Eddy ◽  
Flow Features

A Controlled Diffusion cascade stator blade has been studied numerically using Large Eddy Simulation (LES). The aim of the study is to assess the performance of Large Eddy Simulation in predicting flow features on a highly-loaded blade, including leading-edge separation, transition and turbulent reattachment, particularly at off-design conditions. The need for LES to be performed on high resolution grids is highlighted by preliminary simulations on a mesh typically used in Reynolds-Averaged approaches. On a fine grid, the unsteady flow features captured by time-dependent simulation yield an improvement in surface pressure distributions and boundary layer profiles, although some weaknesses are apparent in the prediction of pressure-side boundary layer properties and wake profiles. The computed loss coefficients show potential for LES to be used to obtain loss-loop data over a wide range of incidence angles.

Large Eddy Simulation of Leading Edge Film Cooling—Part II: Heat Transfer and Effect of Blowing Ratio

2008 ◽  
Vol 130 (4) ◽  
Author(s):  
Ali Rozati ◽  
Danesh K. Tafti
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Large Eddy Simulation ◽  
Transfer Coefficient ◽  
Film Cooling ◽  
Leading Edge ◽  
Blowing Ratio ◽  
Eddy Simulation ◽  
Large Eddy ◽  
Adiabatic Effectiveness

Detailed investigation of film cooling for a cylindrical leading edge is carried out using large eddy simulation (LES). The paper focuses on the effects of coolant to mainstream blowing ratio on flow features and, consequently, on the adiabatic effectiveness and heat transfer coefficient. With the advantage of obtaining unique, accurate, and dynamic results from LES, the influential coherent structures in the flow are identified. Describing the mechanism of jet-mainstream interaction, it is shown that as the blowing ratio increases, a more turbulent shear layer and stronger mainstream entrainment occur. The combined effects lead to a lower adiabatic effectiveness and higher heat transfer coefficient. Surface distribution and span-averaged profiles are shown for both adiabatic effectiveness and heat transfer (presented by Frossling number). Results are in good agreement with the experimental data of Ekkad et al. [1998, “Detailed Film Cooling Measurement on a Cylindrical Leading Edge Model: Effect of Free-Steam Turbulence and Coolant Density,” ASME J. Turbomach., 120, pp. 799–807].

Large Eddy Simulation of Leading Edge Film Cooling: Part II — Heat Transfer and Effect of Blowing Ratio

2007 ◽  
Author(s):  
Ali Rozati ◽  
Danesh K. Tafti
Keyword(s):  
Heat Transfer ◽  
Large Eddy Simulation ◽  
Film Cooling ◽  
Leading Edge ◽  
Turbulent Shear ◽  
Surface Distribution ◽  
Blowing Ratio ◽  
Eddy Simulation ◽  
Large Eddy ◽  
Adiabatic Effectiveness

Detailed investigation of film cooling for a cylindrical leading edge is carried out using Large Eddy Simulation (LES). Part-II of the paper focuses on the effect of coolant to mainstream blowing ratio on flow features and consequently on the adiabatic effectiveness and heat transfer ratio. With the advantage of obtaining unique, accurate and dynamic results from LES, the influential coherent structures in the flow are identified. Describing the mechanism of jet – mainstream interaction, it is shown that as the blowing ratio increases, a more turbulent shear layer and stronger mainstream entrainment occur. The combined effect, leads to a lower adiabatic effectiveness and higher heat transfer coefficient. Surface distribution and span-averaged profiles are shown for both adiabatic effectiveness and heat transfer (presented by Frossling number). Results are in good agreement with the experimental data of Ekkad et al. [12].

Sign in / Sign up

Export Citation Format

Share Document