The Effects of High-Pressure Injection on a Compression-Ignition, Direct Injection of Natural Gas Engine

2005 ◽  
Author(s):  
G. P. McTaggart-Cowan ◽  
H. L. Jones ◽  
S. N. Rogak ◽  
W. K. Bushe ◽  
P. G. Hill ◽  
...  
Keyword(s):  
High Pressure ◽  
Natural Gas ◽  
Direct Injection ◽  
Injection Pressure ◽  
Operating Conditions ◽  
Heavy Duty ◽  
Substantial Impact ◽  
Single Cylinder ◽  
Particulate Matter Emissions ◽  
And Performance

The use of pilot-ignited, direct-injected natural gas fuelling for heavy-duty on-road applications has been shown to substantially reduce NOx and particulate matter emissions. The fuelling process involves the injection of pilot diesel near top-dead-center, followed shortly afterwards by the injection of natural gas at high pressure. The injection pressure of the gas and diesel will substantially affect the penetration of the fuel into the combustion chamber, the break-up and atomization of the diesel spray, and the mixing and nature of the turbulent gas jet. To investigate these influences, a series of experiments were performed on a single-cylinder heavy-duty engine over a range of engine operating conditions (exhaust gas recirculation fraction, engine speed, engine load). Due to the unique nature of the single-cylinder engine, it was possible to hold all other parameters constant while only varying injection pressure. The results indicated that injection pressure had a substantial impact on emissions and performance at high loads, where substantial reductions in PM and CO were observed, with only minor increases in NOx and no significant effect on tHC or fuel consumption. At low loads, no significant impact on either emissions or performance was detected. The effects of injection pressure, while still significant, were found to be reduced at increased engine speeds. Higher injection pressures were found to consistently reduce both the number density and the size of particles in the exhaust stream.

Spark-Ignition and Combustion Characteristics of High-Pressure Hydrogen and Natural-Gas Intermittent Jets

2008 ◽  
Vol 130 (6) ◽  
Author(s):  
Ali Mohammadi ◽  
Masahiro Shioji ◽  
Yuki Matsui ◽  
Rintaro Kajiwara
Keyword(s):  
High Pressure ◽  
Natural Gas ◽  
Ambient Pressure ◽  
Direct Injection ◽  
Injection Pressure ◽  
Spark Ignition ◽  
Constant Volume Combustion Chamber ◽  
Si Engines ◽  
Ignition And Combustion ◽  
Combustion Processes

Recently, an in-cylinder injection method has been considered for the improvement of thermal efficiency in natural-gas and hydrogen spark-ignition (SI) engines. However, the SI and combustion processes of gaseous jets are not well understood. The present study aims to provide fundamental data for the development of direct-injection SI gas engines. The ignition, combustion, and flame behavior of high-pressure and intermittent hydrogen and natural-gas jets in a constant volume combustion chamber were investigated. The effects of injection pressure, nozzle size, ambient pressure, and spark location were also investigated for various spark timings and equivalence ratios.

Combustion Characteristics of Compressed Natural Gas in a Direct Microchannel-Injection Engine under Various Operating Conditions

2013 ◽  
Vol 315 ◽  
pp. 793-798
Author(s):  
Taib Iskandar Mohamad ◽  
How Heoy Geok
Keyword(s):  
Natural Gas ◽  
Ignition Delay ◽  
Direct Injection ◽  
Pressure Rise ◽  
Injection Pressure ◽  
Combustion Characteristics ◽  
Operating Conditions ◽  
Fuel Injector ◽  
Compressed Natural Gas ◽  
Operation Conditions

The combustion characteristics of compressed natural gas (CNG) in a direct microchannel-injection engine under various operating conditions were investigated. In this study, a novel idea for direct CNG microchannel injection was realized with spark plug fuel injector (SPFI). It is a device developed to convert engine to CNG direct injection (DI) operation with minimal cost and technical simplicity. It was installed and tested on a Ricardo E6 single cylinder engine with compression ratio of 10.5:1 without modification on the original engine structure. The engine test was carried out under various operation conditions at 1100 rpm. Burning rates of CNG were measured using normalized combustion pressure method by which the normalized pressure rise due to combustion is equivalent to the mass fraction burned (MFB) at the specific crank angle. The results showed that the MFB of CNG direct injection is substantially faster but initially slower than the ones of port injection. The optimal fuel injection and ignition timings are 190 °CA ATDC and 25 °CA BTDC respectively. The optimal injection pressure was 6 MPa. Combustion durations were not changed with different injection pressures but ignition delay was affected. There was no direct correlation between injection pressure and ignition delay which is most probably due to the effect of charge flow difference. Changing mixture stoichiometry affects the magnitude of ignition delay. Combustion duration, on the other hand increases with leaner mixture.

Experimental Investigation of a Heavy-Duty Compression-Ignition Engine Retrofitted to Natural Gas Spark-Ignition Operation

2019 ◽  
Vol 141 (11) ◽  
Author(s):  
Jinlong Liu ◽  
Hemanth Kumar Bommisetty ◽  
Cosmin Emil Dumitrescu
Keyword(s):  
Natural Gas ◽  
Spark Ignition ◽  
Operating Conditions ◽  
Compression Ignition ◽  
Heavy Duty ◽  
Compression Ignition Engine ◽  
Engine Operation ◽  
Cycle Variation ◽  
Spark Timing ◽  
Ci Engines

Heavy-duty compression-ignition (CI) engines converted to natural gas (NG) operation can reduce the dependence on petroleum-based fuels and curtail greenhouse gas emissions. Such an engine was converted to premixed NG spark-ignition (SI) operation through the addition of a gas injector in the intake manifold and of a spark plug in place of the diesel injector. Engine performance and combustion characteristics were investigated at several lean-burn operating conditions that changed fuel composition, spark timing, equivalence ratio, and engine speed. While the engine operation was stable, the reentrant bowl-in-piston (a characteristic of a CI engine) influenced the combustion event such as producing a significant late combustion, particularly for advanced spark timing. This was due to an important fraction of the fuel burning late in the squish region, which affected the end of combustion, the combustion duration, and the cycle-to-cycle variation. However, the lower cycle-to-cycle variation, stable combustion event, and the lack of knocking suggest a successful conversion of conventional diesel engines to NG SI operation using the approach described here.

Characteristics of Water-in-Diesel Emulsions in a Single Cylinder Compression Ignition Engine

2014 ◽  
Author(s):  
Teja Gonguntla ◽  
Robert Raine ◽  
Leigh Ramsey ◽  
Thomas Houlihan
Keyword(s):  
Fuel Consumption ◽  
Direct Injection ◽  
Engine Performance ◽  
Operating Conditions ◽  
Specific Fuel Consumption ◽  
Brake Specific Fuel Consumption ◽  
Compression Ignition Engine ◽  
Oil Emulsion ◽  
Single Cylinder ◽  
Performance And Emission

The objective of this project was to develop both engine performance and emission profiles for two test fuels — a 6% water-in-diesel oil emulsion (DOE-6) fuel and a neat diesel (D100) fuel. The testing was performed on a single cylinder, direct-injection, water-cooled diesel engine coupled to an eddy current dynamometer. Output parameters of the engine were used to calculate Brake Specific Fuel Consumption (BSFC) and Engine Efficiency (η) for each test fuel. DOE-6 fuels generated a 24% reduction in NOX and a 42% reduction in Carbon Monoxide emissions over the tested operating conditions. DOE-6 fuels presented higher ignition delays — between 1°-4°, yielded 1%–12% lower peak cylinder pressures and produced up to 5.5% lower exhaust temperatures. Brake Specific Fuel consumption increased by 6.6% for the DOE-6 fuels as compared to the D100 fuels. This project is the first research done by a New Zealand academic institution on water-in-diesel emulsion fuels.

scholarly journals Influence of the diesel pilot injector configuration on ethanol combustion and performance of a heavy-duty direct injection engine

2021 ◽  
pp. 146808742110012
Author(s):  
Nicola Giramondi ◽  
Anders Jäger ◽  
Daniel Norling ◽  
Anders Christiansen Erlandsson
Keyword(s):  
Direct Injection ◽  
Engine Performance ◽  
High Load ◽  
Operating Conditions ◽  
Injection System ◽  
Injection Timing ◽  
Diesel Combustion ◽  
Heavy Duty ◽  
Pure Ethanol ◽  
Ethanol Combustion

Thanks to its properties and production pathways, ethanol represents a valuable alternative to fossil fuels, with potential benefits in terms of CO2, NOx, and soot emission reduction. The resistance to autoignition of ethanol necessitates an ignition trigger in compression-ignition engines for heavy-duty applications, which in the current study is a diesel pilot injection. The simultaneous direct injection of pure ethanol as main fuel and diesel as pilot fuel through separate injectors is experimentally investigated in a heavy-duty single cylinder engine at a low and a high load point. The influence of the nozzle hole number and size of the diesel pilot injector on ethanol combustion and engine performance is evaluated based on an injection timing sweep using three diesel injector configurations. The tested configurations have the same geometric total nozzle area for one, two and four diesel sprays. The relative amount of ethanol injected is swept between 78 – 89% and 91 – 98% on an energy basis at low and high load, respectively. The results show that mixing-controlled combustion of ethanol is achieved with all tested diesel injector configurations and that the maximum combustion efficiency and variability levels are in line with conventional diesel combustion. The one-spray diesel injector is the most robust trigger for ethanol ignition, as it allows to limit combustion variability and to achieve higher combustion efficiencies compared to the other diesel injector configurations. However, the two- and four-spray diesel injectors lead to higher indicated efficiency levels. The observed difference in the ethanol ignition dynamics is evaluated and compared to conventional diesel combustion. The study broadens the knowledge on ethanol mixing-controlled combustion in heavy-duty engines at various operating conditions, providing the insight necessary for the optimization of the ethanol-diesel dual-injection system.

Sign in / Sign up

Export Citation Format

Share Document