Development on Simulation Method for Two-Phase Flow in Large Diameter Pipes With 90 Degree Elbows

2020 ◽  
Author(s):  
Yoshiteru Komuro ◽  
Atsushi Kodama ◽  
Yoshiyuki Kondo ◽  
Koichi Tanimoto ◽  
Takashi Hibiki
Keyword(s):  
Flow Regime ◽  
Fluid Model ◽  
Large Diameter ◽  
Simulation Method ◽  
Phase Flow ◽  
Two Phase ◽  
Diameter Pipe ◽  
Two Fluid Model ◽  
Large Diameter Pipes ◽  
Two Fluid

Abstract Two-phase flows are observed in various industrial plants and piping systems. Understanding two-phase flow behaviors such as flow patterns and unsteady void fraction in horizontal and vertical pipes are crucial in improving plant safety. Notably, the flow patterns observed in a large diameter pipe (approx. 4–6 in or larger) are significantly different from those observed in a medium diameter pipe. In a vertical large diameter pipe, no slug flow is observed due to the instantaneous slug bubble breakup caused by the surface instability. Besides, in a horizontal pipe, flow regime transition from stratification of liquid and gas to slug (plug) flow that induces unsteady flow should be taken into account. From this viewpoint, it is necessary to predict the flow regime in horizontal and vertical large diameter pipes with some elbows and to evaluate the unsteady flow regime. In this study, the simulation method based on the two-fluid model is developed. The two-fluid model is considered the most accurate model because the governing equations for mass, momentum, and energy transfer are formulated for each phase. When using the two-fluid model, some constitutive equations should be given in computing the momentum transfer between gas and liquid phases. In this study, several state-of-art constitutive equations of the bubble diameter, the interfacial drag force and non-drag forces such as the lift force and the bubble-bubble collision force, are implemented in the platform of ANSYS FLUENT. The developed simulation method is validated with visualization results and force from an air-water flow at the elbow of the piping system.

Numerical Simulation of Gas Purification by Filtration with Ceramic Filter

2011 ◽  
Vol 356-360 ◽  
pp. 1520-1523
Author(s):  
Hai Xia Li ◽  
Zhan Xu Tie
Keyword(s):  
Numerical Simulation ◽  
Fluid Model ◽  
Simulation Method ◽  
Ceramic Filter ◽  
Phase Flow ◽  
Gas Purification ◽  
Two Phase ◽  
Ceramic Filters ◽  
Two Fluid Model ◽  
Two Fluid

The numerical simulation method is used to analyze the process of gas purification with ceramic filters. The gas /solid two-phase flow field in the ceramic filter vessel was simulated using the Eulerian two-fluid model provided by FLUENT code. The variations of the pressure distribution in the filter cavity were analyzed. The distribution of the dust cake density along the under cleaning filter length was studied.

scholarly journals Natural modes of the two-fluid model of two-phase flow

2021 ◽  
Vol 33 (3) ◽  
pp. 033324
Author(s):  
Alejandro Clausse ◽  
Martín López de Bertodano
Keyword(s):  
Two Phase Flow ◽  
Fluid Model ◽  
Phase Flow ◽  
Two Phase ◽  
Natural Modes ◽  
Two Fluid Model ◽  
Two Fluid

A Physically Based, One-Dimensional Two-Fluid Model for Direct Contact Condensation of Steam Jets Submerged in Subcooled Water

2015 ◽  
Vol 1 (2) ◽  
Author(s):  
David Heinze ◽  
Thomas Schulenberg ◽  
Lars Behnke
Keyword(s):  
Direct Contact ◽  
Two Phase Flow ◽  
Fluid Model ◽  
Interfacial Area ◽  
Phase Flow ◽  
Two Phase ◽  
One Dimensional ◽  
Two Fluid Model ◽  
Contact Condensation ◽  
Two Fluid

A simulation model for the direct contact condensation of steam in subcooled water is presented that allows determination of major parameters of the process, such as the jet penetration length. Entrainment of water by the steam jet is modeled based on the Kelvin–Helmholtz and Rayleigh–Taylor instability theories. Primary atomization due to acceleration of interfacial waves and secondary atomization due to aerodynamic forces account for the initial size of entrained droplets. The resulting steam-water two-phase flow is simulated based on a one-dimensional two-fluid model. An interfacial area transport equation is used to track changes of the interfacial area density due to droplet entrainment and steam condensation. Interfacial heat and mass transfer rates during condensation are calculated using the two-resistance model. The resulting two-phase flow equations constitute a system of ordinary differential equations, which is solved by means of the explicit Runge–Kutta–Fehlberg algorithm. The simulation results are in good qualitative agreement with published experimental data over a wide range of pool temperatures and mass flow rates.

Numerical Simulation of Boiling Two-Phase Flow in Tight-Lattice Rod Bundle by 3-Dimensional Two-Fluid Model Code ACE-3D

2008 ◽  
Author(s):  
Hiroyuki Yoshida ◽  
Takeharu Misawa ◽  
Kazuyuki Takase
Keyword(s):  
Void Fraction ◽  
Lift Force ◽  
Fluid Model ◽  
Phase Flow ◽  
Two Phase ◽  
Rod Bundle ◽  
Fraction Distribution ◽  
Two Fluid Model ◽  
Tight Lattice ◽  
Two Fluid

Two-fluid model can simulate two phase flow less computational cost than inter-face tracking method and particle interaction method. Therefore, two-fluid model is useful for thermal hydraulic analysis in large-scale domain such as a rod bundle. Japan Atomic Energy Agency (JAEA) develops three dimensional two-fluid model analysis code ACE-3D, which adopts boundary fitted coordinate system in order to simulate complex shape channel flow. In this paper, boiling two-phase flow analysis in a tight lattice rod bundle is performed by ACE-3D code. The parallel computation using 126CPUs is applied to this analysis. In the results, the void fraction, which distributes in outermost region of rod bundle, is lower than that in center region of rod bundle. At height z = 0.5 m, void fraction in the gap region is higher in comparison with that in center region of the subchannel. However, at height of z = 1.1m, higher void fraction distribution exists in center region of the subchannel in comparison with the gap region. The tendency of void fraction to concentrate in the gap region at vicinity of boiling starting point, and to move into subchannel as water goes through rod bundle, is qualitatively agreement with the measurement results by neutron radiography. To evaluate effects of two-phase flow model used in ACE-3D code, numerical simulation of boiling two-phase in tight lattice rod bundle with no lift force model (neglecting lift force acting on bubbles) is also performed. From the comparison of numerical results, it is concluded that the effects of lift force model are not so large on overall void fraction distribution in tight lattice rod bundle. However, higher void fraction distribution in center region of the subchannel was not observed in this simulation. It is concluded that the lift force model is important for local void fraction distribution in rod bundles.

A NUMERICAL STUDY OF TWO-PHASE FLOW USING A TWO-DIMENSIONAL TWO-FLUID MODEL

2004 ◽  
Vol 45 (10) ◽  
pp. 1049-1066 ◽  
Author(s):  
Moon-Sun Chung ◽  
Seung-Kyung Pak ◽  
Keun-Shik Chang
Keyword(s):  
Two Phase Flow ◽  
Numerical Study ◽  
Fluid Model ◽  
Phase Flow ◽  
Two Dimensional ◽  
Two Phase ◽  
Two Fluid Model ◽  
Two Fluid

Development of a Transient Mechanistic Two-Phase Flow Model for Wellbores

SPE Journal ◽  
2012 ◽  
Vol 17 (03) ◽  
pp. 942-955 ◽  
Author(s):  
Mahdy Shirdel ◽  
Kamy Sepehrnoori
Keyword(s):  
Shear Stress ◽  
Wall Shear Stress ◽  
Two Phase Flow ◽  
Fluid Model ◽  
Flow Regimes ◽  
Phase Flow ◽  
Two Phase ◽  
Wall Shear ◽  
Two Fluid Model ◽  
Two Fluid

Summary A great deal of research has been focused on transient two-phase flow in wellbores. However, there is lack of a comprehensive two-fluid model in the literature. In this paper, we present an implementation of a pseudo-compositional, thermal, fully implicit, transient two-fluid model for two-phase flow in wellbores. In this model, we solve gas/liquid mass balance, gas/liquid momentum balance, and two-phase energy balance equations to obtain five primary variables: liquid velocity, gas velocity, pressure, holdup, and temperature. This simulator can be used as a stand-alone code or can be used in conjunction with a reservoir simulator to mimic wellbore/reservoir dynamic interactions. In our model, we consider stratified, bubbly, intermittent, and annular flow regimes using appropriate closure relations for interphase and wall-shear stress terms in the momentum equations. In our simulation, we found that the interphase and wall-shear stress terms for different flow regimes can significantly affect the model's results. In addition, the interphase momentum transfer terms mainly influence the holdup value. The outcome of this research leads to a more accurate simulation of multiphase flow in the wellbore and pipes, which can be applied to the surface facility design, well-performance optimization, and wellbore damage estimation.

Sign in / Sign up

Export Citation Format

Share Document