Detailed Observation of Seawater Precipitation With 5×5 Mockup Fuel Bundle Based on X-Ray Computated Tomography Technique

2014 ◽  
Author(s):  
Retsu Kojo ◽  
Akitoshi Hotta ◽  
Masahiro Furuya ◽  
Miyuki Akiba ◽  
Harutaka Hoshi
Keyword(s):  
Boric Acid ◽  
Nuclear Power ◽  
Power Plants ◽  
Water Source ◽  
Sea Salt ◽  
X Ray ◽  
Fuel Bundle ◽  
Water Reactors ◽  
Alternative Water

In order to conform to the new regulatory standard in Japan, seawater is regarded as the alternative water source both for BWRs (Boiling water reactors) and PWRs (Pressurized water reactors). For preventing further accident evolutions occurred in Fukushima Daiichi nuclear power plants, seawater was injected into the reactors for more than one week. With long-term seawater injection, sea salt compositions are condensed and many of them will precipitate when saturated concentrations are exceeded. Unlike corrosion issues, impacts of sea salt precipitation on the heat removal has not been studied widely in the past because it has not been regarded as the alternative water source before Fukushima Daiichi nuclear power plants accident. The existent knowledge base of boric acid precipitation under LOCA conditions was studied. Based on the existent study on impacts of boric acid precipitation under LOCA conditions, the experimental project of seawater consisting of four experiments was proposed. The existent database of physical properties, such as viscosity, of seawater is rather poor under severe accident conditions. In addition, it is likely that boric acid will be injected with water or seawater to prevent re-criticality. It is known that physical properties of boric acid vary widely under high temperature conditions. Measurement of viscosity of the seawater-boric acid mixture was conducted in high temperature using a rotational viscometer. Under conditions equivalent to the estimated bulk coolant conditions under a long-term cooling phase of severe accidents. In this range, no obvious change of viscosity is expected. Then a detailed structure of seawater precipitates was observed using a mockup fuel bundle with 5×5 in the square lattice and 500 mm in the length. Images of precipitates were taken using the X-ray CT. The water level, the concentration of sea salt and the heat flux are employed as experimental parameters. The heat flux, bubble stirring in downstream of spacers and heat loss by a non-heated channel box were identified as influential factors to local and overall precipitates in fuel bundles.

Life Beyond 60 Years: The Importance of Sustaining the Current Fleet of Light Water Reactors in the U.S. and the R&D Needs

2010 ◽  
Author(s):  
Ronaldo Szilard ◽  
Hongbin Zhang
Keyword(s):  
Nuclear Power ◽  
Power Plants ◽  
Nuclear Power Plants ◽  
Superior Performance ◽  
Light Water Reactors ◽  
Economic Operation ◽  
Significant Interest ◽  
Water Reactors ◽  
The U.S

The current fleet of 104 nuclear power plants in the U.S. began their operation with 40 years operating licenses. About half of these plants have their licenses renewed to 60 years and most of the remaining plants are anticipated to pursue license extension to 60 years. With the superior performance of the current fleet and formidable costs of building new nuclear power plants, there has been significant interest to extend the lifetime of the current fleet even further from 60 years to 80 years. This paper addresses some of the key long term technical challenges and identifies R&D needs related to the long term safe and economic operation of the current fleet.

Westinghouse PWR and BWR Reactor Vessel Segmentation Experience in Using Mechanical Cutting Process

2010 ◽  
Author(s):  
Per Segerud ◽  
Joseph Boucau ◽  
Stefan Fallstro¨m ◽  
Paul J. Kreitman
Keyword(s):  
Nuclear Power ◽  
Power Plants ◽  
Reactor Vessel ◽  
Boiling Water Reactors ◽  
Abrasive Waterjet ◽  
Pressurized Water ◽  
Water Reactors ◽  
Mechanical Cutting ◽  
Reactor Internals

Some commercial nuclear power plants have been permanently shut down to date and decommissioned using dismantling methods. Other operating plants have decided to undergo an upgrade process that includes replacement of reactor internals. In both cases, there is a need to perform a segmentation of the reactor vessel internals with proven methods for long term waste disposal. Westinghouse has developed several concepts to dismantle reactor internals based on safe and reliable techniques, including plasma arc cutting (PAC), abrasive waterjet cutting (AWJC), metal disintegration machining (MDM), or mechanical cutting. Mechanical cutting has been used by Westinghouse since 1999 for both Pressurized Water Reactors (PWR’s) and Boiling Water Reactors (BWR’s) and its process has been continuously improved over the years. The complexity of the work requires well designed and reliable tools. Different band saws, disc saws, tube cutters and shearing tools have been developed to cut the reactor internals. All of those equipments are hydraulically driven which is very suitable for submerged applications. Westinghouse experience in mechanical cutting has demonstrated that it is an excellent technique for segmentation of internals. In summary, the purpose of this paper will be to provide an overview of the Westinghouse mechanical segmentation process, based on actual experience from the work that has been completed to date.

scholarly journals Simulation of MASPn Experiments in MISTRA Test Facility with COCOSYS Code

2008 ◽  
Vol 2008 ◽  
pp. 1-7 ◽  
Author(s):  
Mantas Povilaitis ◽  
Egidijus Urbonavičius
Keyword(s):  
Boundary Conditions ◽  
Nuclear Power ◽  
Power Plants ◽  
Volume Fraction ◽  
Characteristic Length ◽  
Initial Conditions ◽  
Test Facility ◽  
Work Package ◽  
Acceptable Agreement

An issue of the stratified atmospheres in the containments of nuclear power plants is still unresolved; different experiments are performed in the test facilities like TOSQAN and MISTRA. MASPn experiments belong to the spray benchmark, initiated in the containment atmosphere mixing work package of the SARNET network. The benchmark consisted of MASP0, MASP1 and MASP2 experiments. Only the measured depressurisation rates during MASPn were available for the comparison with calculations. When the analysis was performed, the boundary conditions were not clearly defined therefore most of the attention was concentrated on MASP0 simulation in order to develop the nodalisation scheme and define the initial and boundary conditions. After achieving acceptable agreement with measured depressurisation rate, simulations of MASP1 and MASP2 experiments were performed to check the influence of sprays. The paper presents developed nodalisation scheme of MISTRA for the COCOSYS code and the results of analyses. In the performed analyses, several parameters were considered: initial conditions, loss coefficient of the junctions, initial gradients of temperature and steam volume fraction, and characteristic length of structures. Parametric analysis shows that in the simulation the heat losses through the external walls behind the lower condenser installed in the MISTRA facility determine the long-term depressurisation rate.

Finite Element Analyses of Residual Stresses in Typical Welded Joints Used in Nuclear Power Plants and Comparisons With Experiments

2010 ◽  
Author(s):  
Dean Deng ◽  
Kazuo Ogawa ◽  
Nobuyoshi Yanagida ◽  
Koichi Saito
Keyword(s):  
Numerical Simulation ◽  
Residual Stress ◽  
Residual Stresses ◽  
Welded Joints ◽  
Nuclear Power ◽  
Power Plants ◽  
Butt Joint ◽  
Welding Residual Stress ◽  
Dissimilar Metal ◽  
Water Reactors

Recent discoveries of stress corrosion cracking (SCC) at nickel-based metals in pressurized water reactors (PWRs) and boiling water reactors (BWRs) have raised concerns about safety and integrity of plant components. It has been recognized that welding residual stress is an important factor causing the issue of SCC in a weldment. In this study, both numerical simulation technology and experimental method were employed to investigate the characteristics of welding residual stress distribution in several typical welded joints, which are used in nuclear power plants. These joints include a thick plate butt-welded Alloy 600 joint, a dissimilar metal J-groove set-in joint and a dissimilar metal girth-butt joint. First of all, numerical simulation technology was used to predict welding residual stresses in these three joints, and the influence of heat source model on welding residual stress was examined. Meanwhile, the influence of other thermal processes such as cladding, buttering and heat treatment on the final residual stresses in the dissimilar metal girth-butt joint was also clarified. Secondly, we also measured the residual stresses in three corresponding mock-ups. Finally, the comparisons of the simulation results and the measured data have shed light on how to effectively simulate welding residual stress in these typical joints.

scholarly journals 14C Release in Various Chemical Forms With Gaseous Effluents From the Paks Nuclear Power Plant

Radiocarbon ◽  
1989 ◽  
Vol 31 (03) ◽  
pp. 754-761 ◽  
Author(s):  
Ede Hertelendi ◽  
György Uchrin ◽  
Peter Ormai
Keyword(s):  
Power Plant ◽  
Nuclear Power Plant ◽  
Nuclear Power ◽  
Liquid Scintillation ◽  
Mean Value ◽  
Scintillation Counting ◽  
Pressurized Water ◽  
The Mean ◽  
Water Reactors

We present results of airborne 14C emission measurements from the Paks PWR nuclear power plant. Long-term release of 14C in the form of carbon dioxide or carbon monoxide and hydrocarbons were simultaneously measured. The results of internal gas-proportional and liquid scintillation counting agree well with theoretical assessments of 14C releases from pressurized water reactors. The mean value of the 14C concentration in discharged air is 130Bqm-3 and the normalized release is equal to 740GBq/GWe · yr. > 95% of 14C released is in the form of hydrocarbons, ca 4% is apportioned to CO2, and <1% to CO. Tree-ring measurements were also made and indicated a minute increase of 14C content in the vicinity of the nuclear power plant.

scholarly journals Stochastic Optimization for Long Term Capital Structures, Systems, and Components Refurbishment and Replacement

2020 ◽  
Author(s):  
Congjian Wang ◽  
Diego Mandelli ◽  
Shawn St Germain ◽  
Curtis Smith ◽  
David Morton ◽  
...  
Keyword(s):  
Stochastic Optimization ◽  
Nuclear Power ◽  
Power Plants ◽  
Capital Investments ◽  
Priority List ◽  
Multi Stage ◽  
Plant Operations ◽  
Economic Constraints ◽  
Returns On Investment

Abstract As commercial nuclear power plants (NPPs) pursue extended plant operations in the form of Second License Renewals (SLRs), opportunities exist for these plants to provide capital investments to ensure long-term, safe, and economic performance. Several utilities have already announced their intention to pursue extended operations for one or more of their NPPs via SLR2. The goal of this research is to develop a risk-informed approach to evaluate and prioritize plant capital investments made in preparation for, and during the period of, extended plant operations to support decisions in NPP operations. In order to prioritize project selection via a risk-informed approach we developed a single decision-making tool that integrates safety/reliability, cost, and stochastic optimization models to provide users with data analysis capabilities to more cost effectively manage plant assets. Both stochastic analysis methods — such as Monte Carlo-based sampling strategies — and multi-stage stochastic optimization strategies are employed to provide priority lists to decision-makers in support of risk-informed decisions. We applied the proposed method to a trial application of projected replacement/refurbishment expenditures for plant capital assets (i.e., structures, systems, and components [SSCs]). The objective is to optimize the SSC replacement/refurbishment schedule in terms of economic constraints, data uncertainties, and SSC reliability data, as well to generate a priority list for maximizing returns on investment.

scholarly journals Reactor Vessel Internals Segmentation Experience using Mechanical Cutting Tools

2013 ◽  
Vol 10 (2) ◽  
pp. 6-10 ◽  
Author(s):  
Petr Pospíšil
Keyword(s):  
Nuclear Power ◽  
Power Plants ◽  
Cutting Tools ◽  
Reactor Vessel ◽  
Boiling Water Reactors ◽  
Abrasive Waterjet ◽  
Pressurized Water ◽  
Water Reactors ◽  
Mechanical Cutting ◽  
Reactor Internals

Abstract Some commercial nuclear power plants have been permanently shut down to date and decommissioned using dismantling methods. Other operating plants have decided to undergo an upgrade process that includes replacement of reactor internals. In both cases, there is a need to perform a segmentation of the reactor vessel internals with proven methods for long term waste disposal. Westinghouse has developed several concepts to dismantle reactor internals based on safe and reliable techniques, including plasma arc cutting (PAC), abrasive waterjet cutting (AWJC), metal disintegration machining (MDM), or mechanical cutting. Mechanical cutting has been used by Westinghouse since 1999 for both Pressurized Water Reactors (PWR’s) and Boiling Water Reactors (BWR’s) and its process has been continuously improved over the years. The complexity of the work requires well designed and reliable tools. Different band saws, disc saws, tube cutters and shearing tools have been developed to cut the reactor internals. All of those equipments are hydraulically driven which is very suitable for submerged applications. Westinghouse experience in mechanical cutting has demonstrated that it is an excellent technique for segmentation of internals. In summary, the purpose of this paper will be to provide an overview of the Westinghouse mechanical segmentation process, based on actual experience from the work that has been completed to date.

scholarly journals Plant Performance History of an Innovative Gate Valve in Critical Service Applications

2017 ◽  
Author(s):  
M. S. Kalsi ◽  
Patricio Alvarez ◽  
Thomas White ◽  
Micheal Green
Keyword(s):  
Nuclear Power ◽  
Power Plants ◽  
Gate Valve ◽  
Plant Performance ◽  
Flow Loop ◽  
Performance History ◽  
Pressurized Water ◽  
Maintenance Costs ◽  
History Of ◽  
Water Reactors

A previous paper [1] describes the key features of an innovative gate valve design that was developed to overcome seat leakage problems, high maintenance costs as well as issues identified in the Nuclear Regulatory Commission (NRC) Generic Letters 89-10, 95-07 and 96-05 with conventional gate valves [2,3,4]. The earlier paper was published within a year after the new design valves were installed at the Pilgrim Nuclear Plant — the plant that took the initiative to form a teaming arrangement as described in [1] which facilitated this innovative development. The current paper documents the successful performance history of 22 years at the Pilgrim plant, as well as performance history at several other nuclear power plants where these valves have been installed for many years in containment isolation service that requires operation under pipe rupture conditions and require tight shut-off in both Pressurized Water Reactors (PWRs) and Boiling Water Reactors (BWRs). The performance history of the new valve has shown to provide significant performance advantage by eliminating the chronic leakage problems and high maintenance costs in these critical service applications. This paper includes a summary of the design, analysis and separate effects testing described in detail in the earlier paper. Flow loop testing was performed on these valves under normal plant operation, various thermal binding and pressure locking scenarios, and accident/pipe rupture conditions. The valve was designed, analyzed and tested to satisfy the requirements of ANSI B16.41 [9]; it also satisfies the requirements of ASME QME 1-2012 [10]. The results of the long-term performance history including any degradation observed and its root cause are summarized in the paper. Paper published with permission.

Experimental Study of Selected Properties of Heavyweight Concrete Based on Analysis of Chemical Composition and Radioactive Elements of its Components

2021 ◽  
Vol 321 ◽  
pp. 113-118
Author(s):  
Janette Dragomirová ◽  
Martin T. Palou ◽  
Katalin Gméling ◽  
Veronika Szilágyi ◽  
Ildikó Harsányi ◽  
...  
Keyword(s):  
Bulk Density ◽  
Nuclear Power ◽  
Power Plants ◽  
Concrete Strength ◽  
Prompt Gamma ◽  
Longitudinal Deformation ◽  
Heavyweight Concrete ◽  
Furnace Slag ◽  
Selection Of

Heavyweight concrete is mostly used for its shielding properties in the nuclear power plants. These properties can already be influenced by the selection of the input materials. In the present study, concrete samples comprised of four-component binders based on CEM I 42.5 R, blast furnace slag, metakaolin and limestone and a mixture of barite and magnetite aggregate, were investigated. Based on Energy Dispersive X-ray Fluorescence, Neutron Activation, and Prompt-Gamma Activation analyses, three concrete designs were prepared and tested. Mechanical, physical (namely cubic compressive strength, bulk density, longitudinal deformation, and dynamic modulus of elasticity) and thermal properties (thermal conductivity coefficient, specific heat capacity, and thermal diffusivity), which should be influenced by the long-term exposure to irradiation were investigated. Presented results confirmed that the prepared samples are heavyweight concrete with bulk density higher than 3400 kg.m-3 with a low level of longitudinal deformation (between 0.265 ‰ and 0.352 ‰). All the prepared samples belong to the C 35/45 concrete strength class.

Sign in / Sign up

Export Citation Format

Share Document