scholarly journals CFD Simulation of Flow Tones From Grazing Flow Past a Deep Cavity

2006 ◽  
Author(s):  
Ted G. Bagwell
Keyword(s):  
Shear Layer ◽  
Cfd Simulation ◽  
Stokes Equations ◽  
Weak Interactions ◽  
Cavity Resonator ◽  
Navier Stokes ◽  
Flow State ◽  
Deep Cavity ◽  
Eddy Simulation ◽  
Lock In

Locked-in flow tones due to shear flow over a deep cavity are investigated using Large Eddy Simulation (LES). An isentropic from of the compressible Navier-Stokes equations (pseudo-compressibility) is used to couple the vertical flow over the cavity mouth with the deep cavity resonances (1). Comparisons to published experimental data (2) show that the pseudo-compressible LES formulation is capable of predicting the feedforward excitation of the deep cavity resonator, as well as the feedback process from the resonator to the flow source. By systematically increasing the resonator damping level, it is shown that strong lock-in results in a more organized shear layer than is observed for the locked-out flow state. By comparison, weak interactions (non-locked-in) produce no change in the shear layer characteristics. This supports the 40 dB definition of lock-in defined in the experiment.

Detached Eddy Simulation of Transonic Rotor Stall Flutter Using a Fully Coupled Fluid-Structure Interaction

2011 ◽  
Author(s):  
Hongsik Im ◽  
Xiangying Chen ◽  
Gecheng Zha
Keyword(s):  
Stokes Equations ◽  
Rotating Stall ◽  
Rotor Blades ◽  
Tip Clearance ◽  
Weno Scheme ◽  
Navier Stokes ◽  
Detached Eddy Simulation ◽  
Eddy Simulation ◽  
Stall Flutter ◽  
Fully Coupled

Detached eddy simulation of an aeroelastic self-excited instability, flutter in NASA Rotor 67 is conducted using a fully coupled fluid/structre interaction. Time accurate compressible 3D Navier-Stokes equations are solved with a system of 5 decoupled modal equations in a fully coupled manner. The 5th order WENO scheme for the inviscid flux and the 4th order central differencing for the viscous flux are used to accurately capture interactions between the flow and vibrating blades with the DES (detached eddy simulation) of turbulence. A moving mesh concept that can improve mesh quality over the rotor tip clearance was implemented. Flutter simulations were first conducted from choke to stall using 4 blade passages. Stall flutter initiated at rotating stall onset, grows dramatically with resonance. The frequency analysis shows that resonance occurs at the first mode of the rotor blade. Before stall, the predicted responses of rotor blades decayed with time, resulting in no flutter. Full annulus simulation at peak point verifies that one can use the multi-passage approach with periodic boundary for the flutter prediction.

Detached-Eddy Simulations Over a Simplified Landing Gear

2002 ◽  
Vol 124 (2) ◽  
pp. 413-423 ◽  
Author(s):  
L. S. Hedges ◽  
A. K. Travin ◽  
P. R. Spalart
Keyword(s):  
Stokes Equations ◽  
Separated Flow ◽  
Flow Fields ◽  
Equation Model ◽  
Landing Gear ◽  
Navier Stokes ◽  
Detached Eddy Simulation ◽  
Navier Stokes Equations ◽  
Instantaneous Flow ◽  
Eddy Simulation

The flow around a generic airliner landing-gear truck is calculated using the methods of Detached-Eddy Simulation, and of Unsteady Reynolds-Averaged Navier-Stokes Equations, with the Spalart-Allmaras one-equation model. The two simulations have identical numerics, using a multi-block structured grid with about 2.5 million points. The Reynolds number is 6×105. Comparison to the experiment of Lazos shows that the simulations predict the pressure on the wheels accurately for such a massively separated flow with strong interference. DES performs somewhat better than URANS. Drag and lift are not predicted as well. The time-averaged and instantaneous flow fields are studied, particularly to determine their suitability for the physics-based prediction of noise. The two time-averaged flow fields are similar, though the DES shows more turbulence intensity overall. The instantaneous flow fields are very dissimilar. DES develops a much wider range of unsteady scales of motion and appears promising for noise prediction, up to some frequency limit.

Large Eddy Simulation of Cross Flow in Pipe Junction

2018 ◽  
Author(s):  
Jiajun Chen ◽  
Yue Sun ◽  
Hang Zhang ◽  
Dakui Feng ◽  
Zhiguo Zhang
Keyword(s):  
Large Eddy Simulation ◽  
Stokes Equations ◽  
Numerical Study ◽  
Three Dimensional ◽  
Cross Flow ◽  
Exciting Force ◽  
Navier Stokes ◽  
Pipe Network ◽  
Eddy Simulation ◽  
Large Eddy

Mixing in pipe junctions can play an important role in exciting force and distribution of flow in pipe network. This paper investigated the cross pipe junction and proposed an improved plan, Y-shaped pipe junction. The numerical study of a three-dimensional pipe junction was performed for calculation and improved understanding of flow feature in pipe. The filtered Navier–Stokes equations were used to perform the large-eddy simulation of the unsteady incompressible flow in pipe. From the analysis of these results, it clearly appears that the vortex strength and velocity non-uniformity of centerline, can be reduced by Y-shaped junction. The Y-shaped junction not only has better flow characteristic, but also reduces head loss and exciting force. The results of the three-dimensional improvement analysis of junction can be used in the design of pipe network for industry.

A Cartesian Explicit Solver for Complex Hydrodynamic Applications

2014 ◽  
Author(s):  
P. Bigay ◽  
A. Bardin ◽  
G. Oger ◽  
D. Le Touzé
Keyword(s):  
Level Set ◽  
Incompressible Flows ◽  
Stokes Equations ◽  
Simulation Method ◽  
Navier Stokes ◽  
Viscous Effects ◽  
Navier Stokes Equations ◽  
Eddy Simulation ◽  
Flow Past A Cylinder ◽  
Explicit Solver

In order to efficiently address complex problems in hydrodynamics, the advances in the development of a new method are presented here. This method aims at finding a good compromise between computational efficiency, accuracy, and easy handling of complex geometries. The chosen method is an Explicit Cartesian Finite Volume method for Hydrodynamics (ECFVH) based on a compressible (hyperbolic) solver, with a ghost-cell method for geometry handling and a Level-set method for the treatment of biphase-flows. The explicit nature of the solver is obtained through a weakly-compressible approach chosen to simulate nearly-incompressible flows. The explicit cell-centered resolution allows for an efficient solving of very large simulations together with a straightforward handling of multi-physics. A characteristic flux method for solving the hyperbolic part of the Navier-Stokes equations is used. The treatment of arbitrary geometries is addressed in the hyperbolic and viscous framework. Viscous effects are computed via a finite difference computation of viscous fluxes and turbulent effects are addressed via a Large-Eddy Simulation method (LES). The Level-Set solver used to handle biphase flows is also presented. The solver is validated on 2-D test cases (flow past a cylinder, 2-D dam break) and future improvements are discussed.

Utilizing Schlieren Imaging to Visualize Heat Transfer Studies

2014 ◽  
Author(s):  
Jacob C. Kaessinger ◽  
Kramer C. Kors ◽  
Jordan S. Lum ◽  
Heather E. Dillon ◽  
Shannon K. Mayer
Keyword(s):  
Heat Transfer ◽  
Undergraduate Students ◽  
Cfd Simulation ◽  
Stokes Equations ◽  
Imaging System ◽  
Empirical Science ◽  
Navier Stokes ◽  
Schlieren Imaging ◽  
Navier Stokes Equations ◽  
Imaging Device

Convective heat transfer beyond explicit solutions to the Navier Stokes equations is often an empirical science. Schlieren imaging is one of the only fluid imaging systems that can directly visualize the density gradients of a fluid using collimated light and refractive properties. The ability to visualize fluid densities is useful in both research and educational fields. A Schlieren imaging device has been constructed by undergraduate students at the University of Portland. The device is used for professorial heat transfer and fluid dynamics research and to help undergraduates visualize and understand natural convection. This paper documents the design decisions, design process, and the final specifications of the Schlieren system. A simple 2-D heated cylindrical model is considered and evaluated using Schlieren imaging, OpenFOAM C.F.D. simulation, and convection analysis using a Nusselt correlation. Results are presented for the three analysis techniques and show excellent verifications between the CFD simulation, Nusselt correlation, and Schlieren imaging system.

scholarly journals Effect of Local Turbulent Structures on the Hot Jet in Transitional Flow

2021 ◽  
Vol 2119 (1) ◽  
pp. 012009
Author(s):  
A Sakhnov ◽  
V V Lukashov
Keyword(s):  
Stokes Equations ◽  
Flow Direction ◽  
Transitional Flow ◽  
Navier Stokes ◽  
Turbulent Structures ◽  
Eddy Simulation ◽  
Eddy Viscosity Model ◽  
Air Jet ◽  
Open Volume ◽  
Subgrid Scales

Abstract Turbulent parts localized in flow direction may arise in a pipe with transitional regime of the stable laminar Poiseuille flow. A key condition for occurrence of such structures is a pipe with rather long length relative to its diameter. Our paper presents numerical modelling of the hot air jet flowing from the long pipe into the cold open volume at Re=2426. The modelling was performed in OpenFOAM software on the basis of the large eddy simulation (LES) method. The WALE (Wall-adapting local eddy-viscosity) model was used for closure of Navier-Stokes equations on subgrid scales. We demonstrated that local turbulent structures have a weak effect on the hot jet at flowing into the cold open volume.

scholarly journals Influence of Dimple Height on Turbulent Heat Transfer of Fin Array with Alternate Convex/Concave Dimples

Inventions ◽  
2020 ◽  
Vol 5 (3) ◽  
pp. 33
Author(s):  
Horng-Wen Wu ◽  
Tang-Hong Chen ◽  
Nugroho-Putra Kelana ◽  
De-An Huang
Keyword(s):  
Flow Field ◽  
Stokes Equations ◽  
Three Dimensional ◽  
Turbulent Heat Transfer ◽  
Navier Stokes ◽  
Bottom Surface ◽  
Turbulent Heat ◽  
Algebraic Equations ◽  
Eddy Simulation ◽  
Turbulent Modeling

This study analyzes transient turbulent modeling of three-dimensional multiple dimpled fin array using large eddy simulation (LES). The Navier–Stokes equations as well as the energy equation were constructed by the finite volume method and then discretized to form algebraic equations, which were solved by semi-implicit method for pressure-linked equation (SIMPLE). The solutions of temperature and velocity were obtained by iterating computation until it converged within each step. This simulation places nine fins on the bottom surface of a channel and changes the height of the dimple (0.4, 0.8, and 1.2 mm) with three different levels of Reynolds number (Re) (3500, 5000, and 6500) to investigate the temperature and flow field without gravity in forced convection. The results indicate that the dimpled fin array can generate vortices between the convex/concave dimples and the fin base and increase the influences of the height of the dimple on the flow field around the fin array. The averaged time-mean of the Nusselt number (Nu) for the dimple height of 0.8 mm is higher than that of the no-dimple case up to 14.4%, while the averaged time-mean Nu for the dimple height of 1.2 mm is lower than that of the no-dimple case up to 11.6%.

2D and 3D Stability of Cavity Flows in High Mach Number Regimes

2019 ◽  
Author(s):  
Parshwanath S. Doshi ◽  
Rajesh Ranjan ◽  
Datta V. Gaitonde
Keyword(s):  
Stability Analysis ◽  
Mach Number ◽  
Stokes Equations ◽  
Navier Stokes ◽  
Cavity Flows ◽  
Flame Holder ◽  
High Mach Number ◽  
Eddy Simulation ◽  
High Mach ◽  
The Stability

Abstract The stability characteristics of an open cavity flow at very high Mach number are examined with BiGlobal stability analysis based on the eigenvalues of the linearized Navier-Stokes equations. During linearization, all possible first-order terms are retained without any approximation, with particular emphasis on extracting the effects of compressibility on the flowfield. The method leverages sparse linear algebra and the implicitly restarted shift-invert Arnoldi algorithm to extract eigenvalues of practical physical consequence. The stability dynamics of cavity flows at four Mach numbers between 1.4 and 4 are considered at a Reynolds number of 502. The basic states are obtained through Large Eddy Simulation (LES). Frequency results from the stability analysis show good agreement when compared to the theoretical values using Rossiter’s formula. An examination of the stability modes reveals that the shear layer is increasingly decoupled from the cavity as the Mach number is increased. Additionally, the outer lobes of the Rossiter modes are observed to get stretched and tilted in the direction of the freestream. Future efforts will extend the present analysis to examine current and potential cavity flame holder configurations, which often have downstream walls inclined to the vertical.

Sign in / Sign up

Export Citation Format

Share Document