Measurement of Soil Suction and Soil-Water Characteristics of Bentonite-Sand Mixtures

2010 ◽  
Author(s):  
Pan Hu ◽  
Qing Yang ◽  
Maotian Luan
Keyword(s):  
Soil Water ◽  
Vapor Phase ◽  
Unsaturated Soils ◽  
Characteristic Curve ◽  
Phase Method ◽  
Soil Suction ◽  
Compacted Bentonite ◽  
Water Characteristics ◽  
Wide Range ◽  
High Level

The soil-water characteristic curve (SWCC) is a widely used experimental means for assessing fundamental properties of unsaturated soils for a wide range of soil suction values. The study of SWCC is helpful because some properties of unsaturated soils can be predicted from it. Nowadays, much attention has been paid to the behaviours of highly compacted bentonite-sand mixtures used in engineering barriers for high level radioactive nuclear waste disposal. It is very important to study the various performances of bentonite-sand mixtures in order to insure the safety of high-level radioactive waste (HLW) repository. After an introduction to vapor phase method and osmotic technique, a laboratory study has been carried out on compacted bentonite-sand mixtures. The SWCC of bentonite-sand mixtures has been obtained and analyzed. The results show that the vapor phase method and osmotic technique is suitable to the unsaturated soils with high and low suction.

Model for the prediction of shear strength with respect to soil suction

1996 ◽  
Vol 33 (3) ◽  
pp. 379-392 ◽  
Author(s):  
S K Vanapalli ◽  
D G Fredlund ◽  
D E Pufahl ◽  
A W Clifton
Keyword(s):  
Shear Strength ◽  
Soil Water ◽  
Unsaturated Soil ◽  
Unsaturated Soils ◽  
Characteristic Curve ◽  
Experimental Studies ◽  
Matric Suction ◽  
Glacial Till ◽  
Soil Suction ◽  
Soil Water Characteristic Curve

Experimental studies on unsaturated soils are generally costly, time-consuming, and difficult to conduct. Shear strength data from the research literature suggests that there is a nonlinear increase in strength as the soil desaturates as a result of an increase in matric suction. Since the shear strength of an unsaturated soil is strongly related to the amount of water in the voids of the soil, and therefore to matric suction, it is postulated that the shear strength of an unsaturated soil should also bear a relationship to the soil-water characteristic curve. This paper describes the relationship between the soil-water characteristic curve and the shear strength of an unsaturated soil with respect to matric suction. Am empirical, analytical model is developed to predict the shear strength in terms of soil suction. The formulation makes use of the soil-water characteristic curve and the saturated shear strength parameters. The results of the model developed for predicting the shear strength are compared with experimental results for a glacial till. The shear strength of statically compacted glacial till specimens was measured using a modified direct shear apparatus. Specimens were prepared at three different water contents and densities (i.e., corresponding to dry of optimum, and wet of optimum conditions). Various net normal stresses and matric suctions were applied to the specimens. There is a good correlation between the predicted and measured values of shear strength for the unsaturated soil. Key words: soil-water characteristic curve, shear strength, unsaturated soil, soil suction, matric suction.

scholarly journals Effect of hysteresis of soil-water characteristic curves on infiltration under different climatic conditions

2016 ◽  
Vol 53 (2) ◽  
pp. 273-284 ◽  
Author(s):  
Rashid Bashir ◽  
Jitendra Sharma ◽  
Halina Stefaniak
Keyword(s):  
Soil Water ◽  
Unsaturated Soils ◽  
Unsaturated Flow ◽  
Expansive Soils ◽  
Characteristic Curve ◽  
Ground Surface ◽  
Temporal Distribution ◽  
Climatic Conditions ◽  
Wide Range ◽  
And Storage

This paper presents results of a numerical modelling exercise that investigates the effects of hysteresis of the soil-water characteristic curve (SWCC) on the infiltration characteristics of soils subjected to four different climatic conditions — from very dry to wet — within the Canadian province of Alberta. Multi-year climate datasets from four different natural regions and subregions of Alberta are compiled, classified, and applied as the soil–atmosphere boundary condition in one-dimensional finite element unsaturated flow models using Hydrus-1D software. Multi-year simulations are carried out with and without consideration of the SWCC hysteresis. Simulation results are analyzed in terms of water balance at the ground surface and temporal distribution and storage of water within the soil domain. It is demonstrated that hysteresis of the SWCC can significantly affect the prediction of flow, redistribution, and storage of water in the unsaturated zone. It is found that for soils that exhibit hysteretic SWCC, consideration of hysteresis in unsaturated flow modelling results in the prediction of lower infiltration and less movement of water through the soil. It is also found that the use of wetting parameters results in the prediction of increased infiltration and movement of water compared with the predictions using drying or hysteretic parameters. It is concluded that, for soils that exhibit a greater degree of SWCC hysteresis, it is important to measure both the drying and wetting branches of the SWCC accurately and that accurate simulation of hysteretic behaviour requires climate datasets at appropriate resolution. The results presented in this paper highlight the importance of considering SWCC hysteresis for a wide range of geotechnical problems, such as soil cover design, prediction of groundwater recharge, contaminant transport through unsaturated soils, soil erosion, slope stability, and swelling–shrinkage of expansive soils.

How to predict hydraulic conductivity of unsaturated soils from an incomplete soil water characteristic curve?

2020 ◽  
Author(s):  
Xingwei Ren ◽  
Qidong Fang ◽  
Xiaojun Chen
Keyword(s):  
Hydraulic Conductivity ◽  
Soil Water ◽  
Unsaturated Soils ◽  
Characteristic Curve ◽  
Ground Surface ◽  
Experimental Conditions ◽  
Flow Process ◽  
Soil Water Characteristic Curve ◽  
Wide Range ◽  
Extensive Experimental Data

<p>Unsaturated soils are those in which pore is filled partially with water and partially with air. They are the most relevant porous medium to human activities, and cover almost all the soils near the ground surface. Hydraulic conductivity (HC) is one of the most important and useful properties of unsaturated soils in numerous studies, including governing flow process, settlement of soil foundations, migration of groundwater and gas hydrate. Unfortunately, direct measurement of HC for unsaturated soils is very difficult with high uncertainty due to its nature of complexity and limited experimental conditions. Thus, indirect estimation of HC from soil water characteristic curve (SWCC) becomes an alternative way and being widely used all over the world.</p><p>Because of the difficulty to reach high suction at the residual state of unsaturated soils, however, the SWCC obtained by laboratory experiments is often incomplete, which will lead to an unreliable estimation of hydraulic conductivity. However, no study has been published on how to estimate hydraulic conductivity of unsaturated soils with incomplete SWCC. In response to this situation, an innovative method was proposed based on the classical van Genuchten model and Mualem model. The proposed method was evaluated by extensive experimental data from existing literature and proved to have an excellent performance in predicting a complete SWCC for a wide range of soils. Also, it exhibits certain superiority in predicting hydraulic conductivity. The limitations of the proposed method were comprehensively discussed, and its corresponding improvement strategies were also addressed. This paper presents a practical way to obtain a more reliable hydraulic conductivity from incomplete SWCC.</p>

A relationship describing the shear strength of unsaturated soils

1999 ◽  
Vol 36 (2) ◽  
pp. 363-368 ◽  
Author(s):  
Daud W Rassam ◽  
David J Williams
Keyword(s):  
Shear Strength ◽  
Soil Water ◽  
Nonlinear Regression ◽  
Unsaturated Soils ◽  
Characteristic Curve ◽  
Three Dimensional ◽  
Matric Suction ◽  
Linear Increase ◽  
Soil Water Characteristic Curve ◽  
Stress Dependent

A relationship describing the shear-strength profile of a desiccating soil deposit is essential for the purpose of analysis, especially when a numerical method is adopted where each zone in a discretised grid is assigned an elevation-dependent shear-strength value. The matric-suction profile of a desiccating soil deposit is nonlinear. Up to the air-entry value, an increase in matric suction is associated with a linear increase in shear strength. Beyond air entry, as the soil starts to desaturate, a nonlinear increase in shear strength occurs. The soil-water characteristic curve is stress dependent, as is the shear-strength gain as matric suction increases. In this paper, a three-dimensional, nonlinear regression analysis showed that a power-additive function is suitable to describe the variation of the shear strength of unsaturated soils with matric suction. The proposed function incorporates the effect of normal stress on the contribution of matric suction to the shear strength.Key words: air-entry value, matric suction, nonlinear regression, soil-water characteristic curve, tailings, unsaturated shear strength.

Entrapment, stability, and persistence of air bubbles in soil water

Soil Research ◽  
1969 ◽  
Vol 7 (2) ◽  
pp. 79 ◽  
Author(s):  
AJ Peck
Keyword(s):  
Hydraulic Conductivity ◽  
Moisture Content ◽  
Soil Water ◽  
Unsaturated Soils ◽  
Equilibration Time ◽  
Air Bubbles ◽  
Air Entrapment ◽  
Water Characteristics ◽  
Spherical Bubbles ◽  
Entrapped Air

Air bubbles in soil water affect both hydraulic conductivity and moisture content at a given capillary potential. Consequently changes in the volume of entrapped air, which are not included in the specification of relationships between hydraulic conductivity, moisture content, and capillary potential, will affect all soil-water interactions. Current understanding of the process of air bubble entrapment during infiltration suggests that, in nature, significant air entrapment will often occur. It is shown that infiltrating water can dissolve only a very small volume of air, much less than the amount usually entrapped. Air bubbles in saturated soils are unstable since their pressure must exceed atmospheric, resulting in a diffusive flux of dissolved air from bubbles to menisci contacting the external atmosphere. However, stable bubbles are possible in unsaturated soils. Bubbles which are constrained by pore architecture to non-spherical shapes are usually stable, and spherical bubbles can be stable when the magnitude of the capillary potential exceeds about 3 bars. An approximate analysis of the characteristic time of bubble equilibration indicates that, in an example, it is of order 104 sec, but it may be greater or less by at least a factor 10. Since the equilibration time will be often at least as large as the period of significant soil temperature changes, it cannot be assumed that the entrapped air in a field soil is in an equilibrium state. In such circumstances unstable bubbles may be quasi-permanent. It is suggested that the slow growth of entrapped bubbles may account for the anomalously slow release of water observed in some outflow experiments. Changes of entrapped air volume may also account for the reported dependence of soil-water characteristics on the magnitude of the steps of capillary potential.

Soil-water characteristics of compacted sandy and cemented soils with and without vegetation

2015 ◽  
Vol 52 (9) ◽  
pp. 1331-1344 ◽  
Author(s):  
W.M. Yan ◽  
Guanghui Zhang
Keyword(s):  
Soil Water ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Rapid Development ◽  
Characteristic Curve ◽  
Degree Of Saturation ◽  
Material Density ◽  
Water Characteristics ◽  
Field And Laboratory Conditions ◽  
Humidity Monitoring

Experiments were undertaken to study the soil-water characteristics of compacted sandy soil (SS) and cemented soil (CS) in field and laboratory conditions. The influence of vegetation and material density on the development of negative pore-water pressure (PWP) and degree of saturation (Sr) in the studied materials was investigated. The field planting experiments demonstrated a promising survival rate of Schefflera heptaphylla in both types of material, while the (SS) promoted better growth of the seedlings than the cemented one. In the field study, PWP and Sr of the compacted SS responded noticeably and promptly to natural drying–wetting cycles. However, the responses in the CS were relatively mild. When subjected to the same drying–wetting cycles, PWP responded more slowly and to a smaller magnitude compared with that of the uncemented counterpart. In addition, Sr changed little in CS. An increase in the density of the SS promoted rapid development of negative PWP, while an opposite trend was observed for CS. Attempts have been made to explain the observations from the perspectives of material permeability and change in water content during a drying period in both soil types. Furthermore, in SS, the development of PWP (with a measurement limit of −90 kPa) was minimally affected by the presence of vegetation, while vegetation noticeably helped the development of negative PWP in CS. Bounds of the soil-water characteristic curve (SWCCs) of the studied materials were presented based on estimates from the drying and wetting scanning curves derived from the field monitoring. A corresponding laboratory study was carried out in an environmental chamber with controllable temperature and humidity. Monitoring results from the laboratory agreed qualitatively with those obtained from the field.

Method for Quick Prediction of Hydraulic Conductivity and Soil-Water Retention of Unsaturated Soils

2018 ◽  
Vol 2672 (52) ◽  
pp. 108-117 ◽  
Author(s):  
Shaoyang Dong ◽  
Yuan Guo ◽  
Xiong (Bill) Yu
Keyword(s):  
Finite Element ◽  
Hydraulic Conductivity ◽  
Soil Properties ◽  
Soil Water ◽  
Unsaturated Soil ◽  
Unsaturated Soils ◽  
Hydraulic Properties ◽  
Water Retention ◽  
Characteristic Curve ◽  
Soil Water Retention

Hydraulic conductivity and soil-water retention are two critical soil properties describing the fluid flow in unsaturated soils. Existing experimental procedures tend to be time consuming and labor intensive. This paper describes a heuristic approach that combines a limited number of experimental measurements with a computational model with random finite element to significantly accelerate the process. A microstructure-based model is established to describe unsaturated soils with distribution of phases based on their respective volumetric contents. The model is converted into a finite element model, in which the intrinsic hydraulic properties of each phase (soil particle, water, and air) are applied based on the microscopic structures. The bulk hydraulic properties are then determined based on discharge rate using Darcy’s law. The intrinsic permeability of each phase of soil is first calibrated from soil measured under dry and saturated conditions, which is then used to predict the hydraulic conductivities at different extents of saturation. The results match the experimental data closely. Mualem’s equation is applied to fit the pore size parameter based on the hydraulic conductivity. From these, the soil-water characteristic curve is predicted from van Genuchten’s equation. The simulation results are compared with the experimental results from documented studies, and excellent agreements were observed. Overall, this study provides a new modeling-based approach to predict the hydraulic conductivity function and soil-water characteristic curve of unsaturated soils based on measurement at complete dry or completely saturated conditions. An efficient way to measure these critical unsaturated soil properties will be of benefit in introducing unsaturated soil mechanics into engineering practice.

Soil-water characteristic curve and consolidation behavior for a compacted silt

2007 ◽  
Vol 44 (3) ◽  
pp. 266-275 ◽  
Author(s):  
Trinh Minh Thu ◽  
Harianto Rahardjo ◽  
Eng-Choon Leong
Keyword(s):  
Soil Water ◽  
Volume Change ◽  
Unsaturated Soils ◽  
Water Pressure ◽  
Characteristic Curve ◽  
Matric Suction ◽  
Confining Stress ◽  
Soil Water Characteristic Curve ◽  
Triaxial Cell ◽  
Isotropic Consolidation

Measurement of the soil-water characteristic curve (SWCC) in the laboratory is commonly conducted under zero confining pressure. However, in the field, the soil is under a confining stress. Therefore, it is important to study the effects of the confining stress on SWCC. In addition, the consolidation curve is normally generated under saturated conditions. However, the soil above the water table is usually unsaturated. Hence, it is also necessary to investigate the effects of matric suction on the characteristics of the consolidation curves. This paper presents the SWCCs under different net confining stresses and the isotropic consolidation curves under different matric suctions that describe the volume change characteristics of unsaturated soils with respect to stress state variables, net normal stress, and matric suction. A series of SWCCs was determined for statically compacted silt specimens in a triaxial cell apparatus under different net confining stresses. Isotropic consolidation tests under different matric suctions were also carried out. The results of the SWCC tests show that the air-entry value increased with increasing net confining stress. The yield points (i.e., yield suction, s0) obtained from the SWCC tests also increased with increasing net confining stress. The results of isotropic consolidation tests indicate the strong influence of matric suction on compressibility and stiffness of the compacted silt specimens.Key words: soil-water characteristic curve, isotropic consolidation, pore-water pressure, volume change, NTU mini suction probe, matric suction.

scholarly journals Performance Evaluation of Four-Parameter Models of the Soil-Water Characteristic Curve

2014 ◽  
Vol 2014 ◽  
pp. 1-12 ◽  
Author(s):  
Siti Jahara Matlan ◽  
Muhammad Mukhlisin ◽  
Mohd Raihan Taha
Keyword(s):  
Soil Water ◽  
Characteristic Curve ◽  
Data Sets ◽  
Modified Model ◽  
Soil Water Characteristic Curve ◽  
Geoenvironmental Engineering ◽  
Wide Range ◽  
Soil Water Characteristic Curves ◽  
Model Equations ◽  
Exponential Variable

Soil-water characteristic curves (SWCCs) are important in terms of groundwater recharge, agriculture, and soil chemistry. These relationships are also of considerable value in geotechnical and geoenvironmental engineering. Their measurement, however, is difficult, expensive, and time-consuming. Many empirical models have been developed to describe the SWCC. Statistical assessment of soil-water characteristic curve models found that exponential-based model equations were the most difficult to fit and generally provided the poorest fit to the soil-water characteristic data. In this paper, an exponential-based model is devised to describe the SWCC. The modified equation is similar to those previously reported by Gardner (1956) but includes exponential variable. Verification was performed with 24 independent data sets for a wide range of soil textures. Prediction results were compared with the most widely used models to assess the model’s performance. It was proven that the exponential-based equation of the modified model provided greater flexibility and a better fit to data on various types of soil.

Sign in / Sign up

Export Citation Format

Share Document