Installation of Monopiles for Offshore Wind Turbines—By Using End-Caps and a Subsea Holding Structure

2011 ◽  
Author(s):  
Arunjyoti Sarkar ◽  
Ove T. Gudmestad
Keyword(s):  
Wind Turbines ◽  
Offshore Wind ◽  
Intermediate Water ◽  
Offshore Wind Turbines ◽  
Correct Location ◽  
End Caps ◽  
Jack Up ◽  
Basic Philosophy ◽  
Water Depths ◽  
Design Challenges

Monopiles are commonly used as foundations for offshore wind turbines at sites with shallow to intermediate water depths (say, up to 40m water depth). The installation of a monopiles is normally carried out by using a bottom supported platform (e.g., a jack-up vessel) which holds the pile at the correct location vertically while driving it into the seabed. In this paper, a methodology for installing a monopile is described which can be applied either by a bottom supported platform or by a floating vessel. The basic philosophy behind this methodology is to support the monopile initially by buoyancy and then by a subsea holding structure. Thus the requirement for a large crane working offshore is eliminated and the marine operation is no longer dependent on the motions of the supporting vessel. Brief geotechnical calculations are presented to support the feasibility of this methodology. Some of the possible design challenges of the installation aids are listed in the conclusion.

Hydrodynamic Modeling of Large-Diameter Bottom-Fixed Offshore Wind Turbines

2015 ◽  
Author(s):  
Erin E. Bachynski ◽  
Harald Ormberg
Keyword(s):  
Wind Turbines ◽  
Environmental Conditions ◽  
Limit State ◽  
Second Order ◽  
Offshore Wind ◽  
Stokes Wave ◽  
Intermediate Water ◽  
Hydrodynamic Loads ◽  
Offshore Wind Turbines ◽  
Wave Kinematics

For shallow and intermediate water depths, large monopile foundations are considered to be promising with respect to the levelized cost of energy (LCOE) of offshore wind turbines. In order to reduce the LCOE by structural optimization and de-risk the resulting designs, the hydrodynamic loads must be computed efficiently and accurately. Three efficient methods for computing hydrodynamic loads are considered here: Morison’s equation with 1) undisturbed linear wave kinematics or 2) undisturbed second order Stokes wave kinematics, or 3) the MacCamy-Fuchs model, which is able to account for diffraction in short waves. Two reference turbines are considered in a simplified range of environmental conditions. For fatigue limit state calculations, accounting for diffraction effects was found to generally increase the estimated lifetime of the structure, particularly the tower. The importance of diffraction depends on the environmental conditions and the structure. For the case study of the NREL 5 MW design, the effect could be up to 10 % for the tower base and 2 % for the monopile under the mudline. The inclusion of second order wave kinematics did not have a large effect on the fatigue calculations, but had a significant impact on the structural loads in ultimate limit state conditions. For the NREL 5 MW design, a 30 % increase in the maximum bending moment under the mudline could be attributed to the second order wave kinematics; a 7 % increase was seen for the DTU 10 MW design.

Modeling Breaking Waves for Fixed-Bottom Support Structures for Offshore Wind Turbines

2018 ◽  
Author(s):  
Hannah M. Johlas ◽  
Spencer Hallowell ◽  
Shengbai Xie ◽  
Pedro Lomonaco ◽  
Matthew A. Lackner ◽  
...  
Keyword(s):  
Wind Turbines ◽  
Water Depth ◽  
Adaptive Mesh Refinement ◽  
Adaptive Mesh ◽  
Breaking Waves ◽  
Offshore Wind ◽  
Breaking Wave ◽  
Intermediate Water ◽  
Offshore Wind Turbines ◽  
Ocean Conditions

Fixed-bottom offshore wind turbines (OWTs) are typically located in shallow to intermediate water depth, where waves are likely to break. Support structure designs for such turbines must account for loads due to breaking waves, but predictions from breaking wave models often disagree with each other and with observed behavior. This variability indicates the need for a better understanding of each model’s strengths and limitations, especially for different ocean conditions. This work evaluates and improves the accuracy of common breaking wave criteria through comparison to Computational Fluid Dynamics (CFD) simulations of breaking waves. The simulated ocean conditions are representative of potential U.S. East Coast offshore wind energy development sites, but the discussion of model accuracy and limitations can be applied to any location with similar ocean conditions. The waves are simulated using CONVERGE, a commercial CFD software that uses a Volume of Fluid (VOF) approach and includes adaptive mesh refinement at the evolving air-water interface. First, the CFD model is validated against experimental data for shoaling and breaking wave surface elevations. Second, 2D simulations of breaking waves are compared to widely-used breaking wave limits (McCowan, Miche, and Goda) for different combinations of wave height, wavelength, water depth, and seafloor slope. Based on these comparisons, the accuracy and limitations of each breaking limit model are discussed. General usage guidelines are then recommended.

scholarly journals Dynamic Response of Articulated Offshore Wind Turbines under Different Water Depths

Energies ◽  
2020 ◽  
Vol 13 (11) ◽  
pp. 2784
Author(s):  
Pei Zhang ◽  
Shugeng Yang ◽  
Yan Li ◽  
Jiayang Gu ◽  
Zhiqiang Hu ◽  
...  
Keyword(s):  
Dynamic Response ◽  
Wind Turbine ◽  
Wind Turbines ◽  
Dynamic Responses ◽  
Wind Pressure ◽  
Offshore Wind ◽  
Offshore Wind Turbine ◽  
Offshore Area ◽  
Offshore Wind Turbines ◽  
Water Depths

Focusing on the transitional depth offshore area from 50 m to 75 m, types of articulated foundations are proposed for supporting the NREL 5 MW offshore wind turbine. To investigate the dynamic behaviors under various water depths, three articulated foundations were adopted and numerical simulations were conducted in the time domain. An in-house code was chosen to simulate the dynamic response of the articulated offshore wind turbine. The aerodynamic load on rotating blades and the wind pressure load on tower are calculated based on the blade element momentum theory and the empirical formula, respectively. The hydrodynamic load is simulated by 3D potential flow theory. The motions of foundation, the aerodynamic performance of the wind turbine, and the loads on the articulated joint are documented and compared in different cases. According to the simulation, all three articulated offshore wind turbines show great dynamic performance and totally meet the requirement of power generation under the rated operational condition. Moreover, the comparison is based on time histories and spectra among these responses. The result shows that dynamic responses of the shallower one oscillate more severely compared to the other designs.

Pitch Angle Control of Floating Offshore Wind Turbines by H∞ Control

2014 ◽  
Vol 134 (8) ◽  
pp. 1096-1103 ◽  
Author(s):  
Sho Tsujimoto ◽  
Ségolène Dessort ◽  
Naoyuki Hara ◽  
Keiji Konishi
Keyword(s):  
Wind Turbines ◽  
Pitch Angle ◽  
Offshore Wind ◽  
Offshore Wind Turbines ◽  
Floating Offshore Wind Turbines

scholarly journals Maintenance Planning of Offshore Wind Turbine Using Condition Monitoring Information

2009 ◽  
Author(s):  
Jose´ G. Rangel-Rami´rez ◽  
John D. So̸rensen
Keyword(s):  
Condition Monitoring ◽  
Wind Turbines ◽  
Wind Farm ◽  
Offshore Structures ◽  
Offshore Wind ◽  
Offshore Wind Turbine ◽  
Maintenance Planning ◽  
Offshore Wind Turbines ◽  
Inspection And Maintenance ◽  
Monitoring Information

Deterioration processes such as fatigue and corrosion are typically affecting offshore structures. To “control” this deterioration, inspection and maintenance activities are developed. Probabilistic methodologies represent an important tool to identify the suitable strategy to inspect and control the deterioration in structures such as offshore wind turbines (OWT). Besides these methods, the integration of condition monitoring information (CMI) can optimize the mitigation activities as an updating tool. In this paper, a framework for risk-based inspection and maintenance planning (RBI) is applied for OWT incorporating CMI, addressing this analysis to fatigue prone details in welded steel joints at jacket or tripod steel support structures for offshore wind turbines. The increase of turbulence in wind farms is taken into account by using a code-based turbulence model. Further, additional modes t integrate CMI in the RBI approach for optimal planning of inspection and maintenance. As part of the results, the life cycle reliabilities and inspection times are calculated, showing that earlier inspections are needed at in-wind farm sites. This is expected due to the wake turbulence increasing the wind load. With the integration of CMI by means Bayesian inference, a slightly change of first inspection times are coming up, influenced by the reduction of the uncertainty and harsher or milder external agents.

Sign in / Sign up

Export Citation Format

Share Document