scholarly journals UK Research Programme on Residual Stresses: A Review of Progress

2008 ◽  
Author(s):  
S. K. Bate ◽  
P. Hurrell ◽  
J. A. Francis ◽  
M. Turski
Keyword(s):  
Residual Stress ◽  
Finite Element ◽  
Residual Stresses ◽  
Stress Measurement ◽  
Experimental Testing ◽  
Research Programme ◽  
Austenitic Steels ◽  
Assessment Procedure ◽  
Engineering Structures ◽  
Modelling Techniques

A long-term UK research programme on residual stresses was launched in 2004. It involves Rolls-Royce plc and Serco Assurance, supported by UK industry and academia. The programme is aimed at progressing the understanding of weld residual stresses and the implementation of finite element simulation and residual stress measurement for assessing the integrity of engineering structures. Following on from this, the intention is then to develop improved guidance on residual stress modelling techniques and then to provide methods and analysis tools for design in order to control and minimise residual stress. The focus of the work to date has been to develop modelling guidelines which can be used by a finite element analyst to predict the residual stresses in austenitic welded components. These guidelines are now drafted and will be incorporated into the next issue of the British Energy R6 defect assessment procedure following peer review. The guidelines have been developed based on the experience that has been attained using various modelling techniques. To support this development, a series of welded mock-ups have been manufactured. The residual stresses in these welds have been measured using various techniques (diffraction and strain relaxation). These measurements are being used to validate the predicted stresses. It is only by corroborating each other that the resulting residual stresses can be confidently used for assessment. Mock-ups are also being used to develop material models for ferritic steel which undergo phase transformations, and to investigate how various weld parameters affect the magnitude and distribution of residual stress. Similarly, mock-ups have been manufactured to investigate the effect of start-stops on residual stresses. The programme is also supported by experimental testing to develop physical and mechanical properties which are required for analysis, i.e. up to melting temperature. Both conventional and miniaturised testing has been used to measure properties in ferritic and austenitic steels. A task has also been undertaken to develop a methodology for providing upper bound residual stress profiles which can be used as an initial estimate of stress for use in structural assessment.

UK Research Programme on Residual Stresses: Progress to Date

2007 ◽  
Author(s):  
S. K. Bate ◽  
A. P. Warren ◽  
C. T. Watson ◽  
P. Hurrell ◽  
J. A. Francis
Keyword(s):  
Residual Stress ◽  
Finite Element ◽  
Residual Stresses ◽  
Stress Measurement ◽  
Research Programme ◽  
Assessment Procedure ◽  
Engineering Structures ◽  
Element Analysis ◽  
Simplifying Assumptions ◽  
Modelling Techniques

A long-term UK research programme on residual stresses was launched in 2004. It involves Rolls-Royce plc and Serco Assurance, and is supported by UK industry and academia. The programme is aimed at progressing the understanding of weld residual stresses and the implementation of finite element simulation and residual stress measurement for assessing the integrity of engineering structures. Following on from this, the intention is then to develop improved guidance on residual stress modelling techniques. In the first two years finite element activities have addressed heat source representation, simplified modelling (e.g. 2D v 3D, bead lumping), material hardening models, high temperature behaviour and phase transformations. It is recognized that simplifying assumptions have to be made in order to reduce the computational run-time and modelling complexity, especially for multi-pass welds. The effects of these assumptions on the determined stresses have been considered by carrying out finite element analyses of welded mock-ups. The welded mock-ups have been developed to provide measured residual stress data which are necessary to validate the modelling techniques that have been developed. These activities have been used to support the development of guidelines on the use finite element analysis to predict residual stresses in welded components. These guidelines will be incorporated in the next issue of the British Energy R6 defect assessment procedure.

New UK Research Programme on Residual Stresses

2006 ◽  
Author(s):  
Steve K. Bate ◽  
Chris Watson
Keyword(s):  
Residual Stress ◽  
Finite Element ◽  
Residual Stresses ◽  
Structural Integrity ◽  
Stress Measurement ◽  
Research Work ◽  
Research Programme ◽  
Residual Stress Measurement ◽  
Engineering Structures ◽  
The Uk

A new long-term research programme has been launched in the UK. This involves Rolls-Royce plc and Serco Assurance, supported by UK industry and academia. A significant part of this programme is aimed at progressing the understanding of weld residual stresses and the implementation of finite element simulation and residual stress measurement for assessing the structural integrity of engineering structures and components. The work includes: (1) Finite element modelling to investigate heat source representation, material behaviour and 3D v 2D effects. (2) Design and manufacture of mock-ups for supporting validation. (3) Residual stress measurement. (4) Weld design. (5) Residual stress profiles. (6) Material testing. (7) Development of a procedure for residual stress modelling. The work is being undertaken by a combination of finite element analyses and residual stress measurement using a variety of techniques. This paper presents an overview of the research work being undertaken and provides examples of the outcome of some of the studies obtained to-date.

Experimental characterization and finite element modeling of the residual stresses in laser-assisted mechanical micromachining of Inconel 625

2015 ◽  
Vol 231 (10) ◽  
pp. 1735-1751 ◽  
Author(s):  
Avik Samanta ◽  
Mahesh Teli ◽  
Ramesh Singh
Keyword(s):  
Residual Stress ◽  
Finite Element ◽  
Residual Stresses ◽  
Cutting Forces ◽  
Laser Heating ◽  
Stress Measurement ◽  
Cutting Speed ◽  
Inconel 625 ◽  
Beam Diameter ◽  
Mechanical Micromachining

Laser-assisted mechanical micromachining offers the ability to machine difficult-to-cut materials, like superalloys and ceramics, more efficiently and economically by laser-induced localized thermal softening prior to cutting. Laser-assisted mechanical micromachining is a micromachining process with localized laser heating which could affect the cutting forces and the machined surface integrity. The residual stresses obtained in the laser-assisted mechanical micromachining process depend on both mechanical loading and the laser heating. This article focuses on the experimental process characterization and prediction of the cutting forces and the residual stresses in a laser-assisted mechanical micromachining–based orthogonal machining of Inconel 625. The results show that the laser assistance reduces the mean cutting forces by ∼25% and enhances the normal compressive residual stress at the surface by ∼50%. Since microscale residual stress measurement is very time-intensive, a coupled-field thermo-mechanical finite element model of laser-assisted mechanical micromachining has been developed to predict the temperature, cutting forces and the residual stresses. The cutting forces and residual stresses’ predictions are in good agreement with the measured values during machining. In addition, parametric simulations have been carried out for laser power, cutting speed, cutting edge radius, rake angle, laser location and laser beam diameter to study their effect on cutting forces and surface residual stresses.

Residual Stress Measurement in a Ceramic-Metallic Graded Material

2002 ◽  
Vol 124 (2) ◽  
pp. 185-191 ◽  
Author(s):  
Michael R. Hill ◽  
Wei-Yan Lin
Keyword(s):  
Residual Stress ◽  
Finite Element ◽  
Error Analysis ◽  
Residual Stresses ◽  
Stress Measurement ◽  
Pure Titanium ◽  
Titanium Boride ◽  
Residual Stress Measurement ◽  
Graded Material ◽  
Strain Release

This paper presents experimental measurements of the through-thickness distribution of residual stress in a ceramic-metallic functionally graded material (FGM). It further presents an error analysis and optimization of the residual stress measurement technique. Measurements are made in a seven-layered plate with a base of commercially pure titanium and successive layers containing an increasing proportion of titanium-boride, reaching 85% titanium-boride in the final layer. The compliance method is employed to determine residual stress, where a slot is introduced using wire electric-discharge machining and strain release is measured as a function of increasing slot depth. Strain release measurements are used with a back-calculation scheme, based on finite element simulation, to provide residual stresses in the FGM. The analysis is complicated by the variation of material properties in the FGM, but tractable due to the flexibility of the finite element method. The Monte Carlo approach is used for error analysis and a method is described for optimization of the functional form assumed for the residual stresses. The magnitude and variation of the resulting residual stress distributions and several aspects of the error analyses are discussed.

scholarly journals Using Welding Simulation and Ultrasonic Method to Evaluate Residual Stress in Stainless Steel Welded Plates

2012 ◽  
Author(s):  
Yashar Javadi ◽  
Mohammadreza Hadizadeh Raeisi ◽  
Hamed Salimi Pirzaman ◽  
Mehdi Ahmadi Najafabadi
Keyword(s):  
Residual Stress ◽  
Finite Element ◽  
Stainless Steel ◽  
Residual Stresses ◽  
Acoustic Waves ◽  
Stress Measurement ◽  
Bulk Material ◽  
Three Dimensional ◽  
Ultrasonic Waves ◽  
Welding Simulation

When a material is under mechanical load, the stresses change the velocity of acoustic waves because of acoustoelastic effect. This property can be employed for stress measurement in the material itself when the stress concerns the surface of the material, or in the bulk material. This technique involves with critically refracted longitudinal waves that propagate parallel to the surface, i. e. LCR waves. This paper presents a three dimensional thermo-mechanical analysis to evaluate welding residual stresses in plate-plate joint of AISI stainless steel 304L. After finite element simulation, the residual stresses were evaluated by LCR ultrasonic waves. This paper introduces a combination of “Finite Element Welding Simulation” and “Ultrasonic Stress Measurement using the LCR Wave” which is called as “FELcr”. The capabilities of FELCR in residual stress measurement are confirmed here. It has been shown that predicted residual stress from three dimensional FE analyses is in reasonable agreement with measured residual stress from LCR method.

The Validation of Weld Residual Stresses for Use in Structural Integrity Assessment

2011 ◽  
Vol 70 ◽  
pp. 297-302 ◽  
Author(s):  
Steve K. Bate ◽  
P. John Bouchard
Keyword(s):  
Residual Stress ◽  
Finite Element ◽  
Residual Stresses ◽  
Structural Integrity ◽  
Measurement Techniques ◽  
Element Analysis ◽  
Integrity Assessment ◽  
Modelling Techniques ◽  
High Level ◽  
Assessment Procedures

The continued safe and reliable operation of plant invariably has to consider the assessment of defects in welded structural components. This requires some estimate of the residual stresses that have developed during the welding fabrication process. For as-welded structures these stresses can be of yield magnitude. Engineering critical assessment procedures such as R6, BS 7910, FITNET and API 579-1 provide simplified estimates, bounding profiles or advice on detailed analysis or measurement which can be applied to provide conservative estimates of the remaining life of plant. The use of finite element analysis (FEA) is being applied more frequently to predict residual stresses in welded components for assessment purposes. This calculation involves complex non-linear analyses with many assumptions. As a consequence, the accuracy and reliability of solutions is variable. In order to improve the consistency of weld modelling, and hence the accuracy and confidence in their use, a set of Guidelines covering the calculation of residual stresses have been developed. The residual stress calculations need to be validated before the results can be used in assessments and guidance on how to demonstrate the required standard of validation proof is provided with these Guidelines. The level of validation required, depends on the problem being solved and the sensitivity of the assessment to the presence of residual stress. For example a high level of validation may be required for assessments of safety critical plant. To support these calculations, measurements are required and a series of ‘Weld Residual Stress Benchmarks’, describing welded mock-ups which have been measured using various measurement techniques, are being collated which the users can then refer to when validating their finite element modelling techniques and thus provide a greater confidence in the predicted results.

Clamping Effect on the Welding Deformations in Dissimilar Welded Pipes (Joints) With Varied Thicknesses: Axial and Radial Shrinkage

2020 ◽  
Author(s):  
Bridget Kogo ◽  
Bin Wang ◽  
Mahmoud Chizari
Keyword(s):  
Residual Stress ◽  
Finite Element ◽  
Residual Stresses ◽  
Finite Element Simulation ◽  
Stress Measurement ◽  
Vertical Displacement ◽  
Hole Drilling ◽  
Element Simulation ◽  
Radial Shrinkage ◽  
Ultrasonic Stress Measurement

Abstract This study investigates and evaluates the welding residual stresses and deformations in the dissimilar material MSSS metals in order to verify the clamping effect on the residual stresses and deformations and entails comparison with the finite element simulation, the critically reflected longitudinal ultrasonic stress measurement and the hole-drilling residual stresses in a Butt-welded plate courtesy of Javadi et al [1]. The angular shrinkage measurement and vertical displacement were used to achieve this objective. The outcome of the study proved that the measurement of residual stress using protractor is an effective way of differentiating the influence of clamps on the longitudinal stresses.

Manufacture, Residual Stress Measurement and Analysis of a VVER-440 Nozzle Mockup

2013 ◽  
Author(s):  
Levente Tatár ◽  
Gyula Török ◽  
David J. Smith ◽  
Son Do ◽  
Carsten Ohms ◽  
...  
Keyword(s):  
Residual Stress ◽  
Finite Element ◽  
Residual Stresses ◽  
Stress Measurement ◽  
Welding Process ◽  
Full Scale ◽  
Residual Stress Measurement ◽  
Contour Method ◽  
Scale Model ◽  
Fe Model

As part of the STYLE EU FP7 project a modified 1:5 scale replica of a VVER-440 type reactor pressure vessel inlet nozzle was manufactured. The nozzle included a dissimilar metal weld of the type found in full-scale nozzles. This scale model was developed to permit accurate measurements to be made and detailed finite element (FE) models to be developed without recourse to using a full scale mock-up. It was also found that a full-scale mock-up would not permit the application of certain residual stress measurement methods. Temperatures and displacements were recorded during welding of the dissimilar metals, with measurements used to guide simulation of the welding process using finite element models. Through thickness residual stress profiles were measured using a comprehensive range of different techniques, such as deep hole drilling, neutron diffraction, magnetic Barkhausen noise. Usage of contour method had been planned too, but it but could not be accomplished in due time. The measured residual stresses obtained by the different methods are presented and compared. Measured residual stresses, temperatures and displacements were then used to validate the results derived from the FE model.

scholarly journals Should Residual Stresses Be Taken Into Account in Structural Integrity Assessment of Offshore Monopiles?

2018 ◽  
Author(s):  
Anais Jacob ◽  
Jeferson Araujo de Oliveira ◽  
Ali Mehmanparast ◽  
Foroogh Hosseinzadeh ◽  
Filippo Berto
Keyword(s):  
Residual Stress ◽  
Residual Stresses ◽  
Structural Integrity ◽  
Stress Measurement ◽  
Corrosion Cracking ◽  
Residual Stress Measurement ◽  
Offshore Wind ◽  
Contour Method ◽  
Assessment Procedure ◽  
Integrity Assessment

A key challenge in the Offshore Wind industry is assuring the life-cycle structural integrity of wind turbine foundation monopiles. This is due to harsh environmental aspects as well as the loading regime (i.e. constant exposure to wave and wind forces introducing both fatigue and corrosion damage). Welding is a widely used joining technique for the manufacturing of offshore monopile structures. However, this is an aggressive process that introduces high levels of residual stress, which in turn may lead to reduced fatigue life, corrosion cracking resistance and accelerated degradation mechanisms. This study presents evidence that a measurement-informed strategy could be used towards developing a more reliable structural integrity assessment procedure for offshore monopile structures by taking into account the effect of residual stresses. A welded mock-up, 90 mm thick, 2600 mm wide and 800 mm long plate, was fabricated using a typical double-V welding procedure following current industrial practice. The contour method of residual stress measurement was employed to map residual stresses in the welded mock-up as well as in the CT specimens extracted from the weld region of the plate for future fatigue tests. Residual stress measurement results show that the mock-up plate contained tensile residual stresses above yield in the core of the weld, while the extracted CT specimens had lower though still significant residual stress levels. These results indicate that if the initial residual stresses are not carefully considered during fatigue or corrosion cracking tests, the results from the CT specimens alone will likely result in misleading structural life estimations.

Finite Element and Experimental Analysis of Residual Stresses in Electron Beam Welded Nickel-Based Superalloys

2021 ◽  
Author(s):  
Tom Saju ◽  
M. Velu
Keyword(s):  
Residual Stress ◽  
Finite Element ◽  
Electron Beam ◽  
Residual Stresses ◽  
Electron Beam Welding ◽  
Stress Measurement ◽  
Welding Parameters ◽  
Element Analysis ◽  
Longitudinal Residual Stress ◽  
Nimonic 80A

In this paper, two different nickel-based superalloys, namely Inconel 718 and Nimonic 80A were joined using electron beam welding techniques with three different welding parameters. A finite element analysis (FEA) using Abaqus software was carried out to calculate the residual stresses due to welding. Both transverse and longitudinal residual stresses were determined. Also, an X-ray residual stress measurement system, μ-X360 Ver. 2.5.6.2 was used for measuring transverse residual stress along and across the weld centerline. The transverse residual stress found by FEA and that measured experimentally was nearly the same thus validating the FEA. Also, the peak values of longitudinal residual stress found using the FEA were close to the yield strengths of the base metals as found elsewhere.

Sign in / Sign up

Export Citation Format

Share Document