Design of a Large Diameter Steel Reinforced Plastic Pipe

2011 ◽  
Author(s):  
Jun Shi ◽  
Jing Rao ◽  
Jianfeng Shi ◽  
Ping Xu ◽  
Taiqing Shao ◽  
...  
Keyword(s):  
Structural Parameters ◽  
Steel Wire ◽  
Large Diameter ◽  
Small Diameter ◽  
High Strength ◽  
External Pressure ◽  
Wire Mesh ◽  
Plastic Pipe ◽  
Reinforced Plastic ◽  
Steel Wire Mesh

A steel reinforced plastic pipe (PSP), which is composed of two layers of high density polyethylene (HDPE) matrix and a high strength steel wire mesh skeleton, has wide applications in many industrial areas, such as gas and petroleum transportation, etc. In order to achieve higher efficency and lower costs, a large diameter PSP has been developed. However, requirements of the large diameter PSP in safety and economy are much higher, compared with those small diameter PSPs, and some potential problems should be taken into account. In this paper, relevant structural parameters of the large diameter PSP are determined, based on a previously proposed model, and a short-term burst test is carried out. The experiment results agree with the theoretical results quite well. Subsequently, the resistance of vertical pressure and uniform external pressure are evaluated by using experiment investigation and finite element method, respectively. And corresponding results indicate the large diameter PSP with determined structural parameters is qualified to use.

Experimental Study on RC Beams Strengthened by a Novel Large Diameter Pre-stressed Stainless Steel Wire Mesh – Mortar Structure

2012 ◽  
Vol 256-259 ◽  
pp. 911-917
Author(s):  
Meng Jie Zhang ◽  
Ming Hua He ◽  
Ke Gui Xin ◽  
Tian Shen Zhang ◽  
Yuan Ma
Keyword(s):  
Stainless Steel ◽  
Steel Wire ◽  
Large Diameter ◽  
Small Diameter ◽  
Wire Mesh ◽  
Stainless Steel Wire ◽  
Engineering Practice ◽  
Rc Beams ◽  
Stainless Steel Wire Mesh ◽  
Steel Wire Mesh

The pre-stressed stainless steel wire mesh (SSWM) –mortar (M) is a pre-stressed laminate structure for structural strengthening and rehabilitation. Pre-stressing the stainless steel wire mesh is the key technology for engineering practice. A jogged anchor is proposed for anchoring large diameter SSWM conveniently. The flexural performances of 5 damaged RC beams strengthened by pre-stressed SSWM-M and one referential RC beam were tested. The experimental results indicates that the large diameter pre-stressed SSWM-M has a better performance in controlling the crack growth, restoring the flexural capacity and stiffness than the small diameter pre-stressed SSWM-M.

Analysis the Flexural Properties of RC Beams Strengthened by High Strength Steel Wire Mesh and Polymer Mortar Using the Finite Element

2013 ◽  
Vol 444-445 ◽  
pp. 1067-1071
Author(s):  
Li Ping Sun ◽  
Zheng Liu ◽  
Yan Zi Liu
Keyword(s):  
High Strength Steel ◽  
Steel Wire ◽  
High Strength ◽  
Wire Mesh ◽  
Flexural Properties ◽  
Rc Beams ◽  
Reinforced Beams ◽  
Practical Engineering ◽  
Polymer Mortar ◽  
Steel Wire Mesh

The high strength steel wire mesh and polymer mortar reinforcement technology has the advantages of high strength, high temperature resistance,corrosion,resistant, etc. In this paper,we analysis the flexural properties of RC beams strengthened by it using ANSYS.To bear the same moment in the same area of the reinforcement steel strand, and then get effect of different span and different reinforcement methods (comparative beam, direct reinforced beams,and secondary load of reinforced beams) on flexural load-carrying capacity and deflection, then compare and analysis,and draws the conclusion which can provide reference for practical engineering.

Finite Element Analysis of Shear Behavior of Reinforced Concrete Beam Strengthened by High-Strength Steel Wire Mesh

2013 ◽  
Vol 482 ◽  
pp. 15-19
Author(s):  
Chen Xing Yang ◽  
Zheng Liu ◽  
Li Ping Sun ◽  
Jiong Li
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Shear Strength ◽  
High Strength Steel ◽  
Steel Wire ◽  
High Strength ◽  
Wire Mesh ◽  
Element Analysis ◽  
Strength And Stiffness ◽  
Steel Wire Mesh

Based on the experimental study of shear strengthened of reinforced concrete rectangular beam strengthened by high-strength steel wire mesh and polymer mortar , the finite element extended analysis was used. The finite element analysis software showed that with the increasing of the strand dosage and reinforcement strand length,the shear strength and stiffness of strengthened members improved . However,with the increasing of shear span ratio , the shear strength and stiffness reduced obviously .

The Progress and Prospects of the Research on Reinforcing RC Column with High Strength Steel Wire Mesh and High-Performance Mortar

2014 ◽  
Vol 488-489 ◽  
pp. 809-812
Author(s):  
Jia Qi Wang ◽  
Min Duan ◽  
Ping Shi Li
Keyword(s):  
High Performance ◽  
Steel Wire ◽  
High Strength ◽  
Wire Mesh ◽  
Rc Column ◽  
Project Study ◽  
Beam Shear ◽  
Stainless Steel Wire Mesh ◽  
Steel Wire Mesh ◽  
Shear Bending

The high strength stainless steel wire mesh and high-performance mortar reinforcement has been gradually applied in construction, bridge reinforcement project. Study of the reinforcement at home and abroad mainly focus on research of strengthening RC beam shear, bending, and seismic performance. Although the application of RC column has already been carried out, there is also a short of basic technical an applied research for further study. After looking through a large amount of references, this article gives a summary of the present study about reinforcing RC column with the reinforcement, draws some conclusions and predicts the prospect of development.

Studies on RC Beams Strength with Steel Wires Using Nolinear Finite Element Method

2013 ◽  
Vol 690-693 ◽  
pp. 895-899
Author(s):  
Cao Song ◽  
Jing Ya Zhou ◽  
Hong Mei Zhang
Keyword(s):  
Finite Element ◽  
Failure Mode ◽  
Steel Wire ◽  
High Strength ◽  
Wire Mesh ◽  
Finite Element Software ◽  
Reinforced Beams ◽  
Before And After ◽  
Polymer Mortar ◽  
Steel Wire Mesh

High strength stainless steel wire mesh-polymer mortar reinforcement method was a kind of advanced reinforcement technique.The present study attempted to do a model analysis on the test of the high strength steel wire mesh-polymer mortar reinforcement of less stress beams by using finite element software ANSYS. The study was conducted through the analysis of the three factors of the tested bending reinforcement beam’s deflection, deformation and stress and comparison of the changes of the beam’s ultimate load and failure mode before and after reinforcement.The results of ANSYS analysis and the test showed that the failure mode shifts from less reinforcement damaged into reinforcement destruction;the crack loading value of the reinforced beams increased indicating that the beam bottom reinforcement layer had a significant effect on the increase of the beam’s crack loading. Increased significantly compared to non-reinforced ultimate bearing capacity of reinforced beams. the ANSYS finite element simulation agrees well with the experimental value.

Preparation of Super Hydrophobic Surfaces by the Stainless Steel Wire Mesh as Templates

2012 ◽  
Vol 562-564 ◽  
pp. 56-59 ◽  
Author(s):  
Jian Zhuang ◽  
Meng Meng Du ◽  
Heng Zhi Cai ◽  
Ya Jun Zhang ◽  
Da Ming Wu
Keyword(s):  
Contact Angle ◽  
Stainless Steel ◽  
Steel Wire ◽  
Contact Angles ◽  
Wire Mesh ◽  
Stainless Steel Wire ◽  
Hydrophobic Surfaces ◽  
Water Contact ◽  
Stainless Steel Wire Mesh ◽  
Steel Wire Mesh

A facile method for manufacturing super hydrophobic surfaces is presented using the stainless steel wire mesh as templates. The rough surfaces of polymers including polycarbonate, polypropylene and PMMA are prepared with hot embossing on different specifications of stainless steel wire mesh. Scanning electron microscopy (SEM) results reveal that the surfaces roughness of the polymers can be controlled by selecting templates. Contact angle measurement shows that the water contact angles(WCA) rise with the increase of surface roughness, especially, the water contact angle on the PC surfaces prepared with specifications of 635mesh screen can reach to 152.3°, alias super hydrophobic surfaces.

Sign in / Sign up

Export Citation Format

Share Document