Comparison Between Single Level and Bi-Level Dynamic Stabilization in Lumbar Spondylolisthesis: A Finite Element Study

2007 ◽  
Author(s):  
A. S. Khere ◽  
A. Kiapour ◽  
J. Jangra ◽  
V. K. Goel ◽  
A. Biyani ◽  
...  
Keyword(s):  
Finite Element ◽  
Severe Pain ◽  
Element Model ◽  
Dynamic Stabilization ◽  
Single Level ◽  
Pars Interarticularis ◽  
Lumbar Spondylolisthesis ◽  
Older Populations ◽  
The Finite Element Model ◽  
Anterior Posterior

Lumbar spondylolisthesis is an extension of spondylolysis in which breakage of the vertebrae occurs at the pars interarticularis causing the vertebrae to slip forward. Spondylolisthesis is seen in both younger and older populations with most lesions occurring at the L4-L5 or L5-S1 level. Although the forward slippage of the vertebra does not usually exceed 30% of the body’s anterior-posterior width, possible spinal stenosis and nerve impingement may lead to severe pain and other complications. The purpose of this study is to determine the effect of single level and bi-level dynamic stabilization in reducing the spondylolisthesis. We used the finite element model for this purpose since it is not practical to procure specimens with spondylolisthesis for an experimental investigation.

Redrawing Operation a Star Shape from Cylindrical Shape Using Experimental and FE Analysis

2020 ◽  
Vol 38 (1A) ◽  
pp. 25-32
Author(s):  
Waleed Kh. Jawad ◽  
Ali T. Ikal
Keyword(s):  
Finite Element ◽  
Effective Strain ◽  
Element Model ◽  
Cylindrical Shape ◽  
Element Analysis ◽  
Punch Force ◽  
Maximum Value ◽  
Element Simulation ◽  
Blank Sheet ◽  
The Finite Element Model

The aim of this paper is to design and fabricate a star die and a cylindrical die to produce a star shape by redrawing the cylindrical shape and comparing it to the conventional method of producing a star cup drawn from the circular blank sheet using experimental (EXP) and finite element simulation (FES). The redrawing and drawing process was done to produce a star cup with the dimension of (41.5 × 34.69mm), and (30 mm). The finite element model is performed via mechanical APDL ANSYS18.0 to modulate the redrawing and drawing operation. The results of finite element analysis were compared with the experimental results and it is found that the maximum punch force (39.12KN) recorded with the production of a star shape drawn from the circular blank sheet when comparing the punch force (32.33 KN) recorded when redrawing the cylindrical shape into a star shape. This is due to the exposure of the cup produced drawn from the blank to the highest tensile stress. The highest value of the effective stress (709MPa) and effective strain (0.751) recorded with the star shape drawn from a circular blank sheet. The maximum value of lamination (8.707%) is recorded at the cup curling (the concave area) with the first method compared to the maximum value of lamination (5.822%) recorded at the cup curling (the concave area) with the second method because of this exposure to the highest concentration of stresses. The best distribution of thickness, strains, and stresses when producing a star shape by

Analysis of Hydroelectric Unit’s Upper Bracket Based on Test and FEM

2014 ◽  
Vol 721 ◽  
pp. 131-134
Author(s):  
Mi Mi Xia ◽  
Yong Gang Li
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
Element Model ◽  
The Finite Element Method ◽  
Ansys Software ◽  
Element Analysis ◽  
Hydroelectric Unit ◽  
The Finite Element Analysis ◽  
Strain Rosette ◽  
The Finite Element Model

To research the load upper bracket of Francis hydroelectric unit, then established the finite-element model, and analyzed the structure stress of 7 operating condition points with the ANSYS software. By the strain rosette test, acquired the data of stress-strain in the area of stress concentration of the upper bracket. The inaccuracy was considered below 5% by analyzing the contradistinction between the finite-element analysis and the test, and match the engineering precision and the test was reliable. The finite-element method could be used to judge the stress of the upper bracket, and it could provide reference for the Structural optimization and improvement too.

Analysis of Premium Connection of Connecting and Sealing Ability Loaded by Axial Tensile Loads

2012 ◽  
Vol 268-270 ◽  
pp. 737-740
Author(s):  
Yang Yu ◽  
Yi Hua Dou ◽  
Fu Xiang Zhang ◽  
Xiang Tong Yang
Keyword(s):  
Finite Element ◽  
Contact Pressure ◽  
Tensile Load ◽  
Element Model ◽  
Sealing Ability ◽  
Axial Tensile ◽  
High Level ◽  
Maximum Contact ◽  
Contact Pressures ◽  
The Finite Element Model

It is necessary to know the connecting and sealing ability of premium connection for appropriate choices of different working conditions. By finite element method, the finite element model of premium connection is established and the stresses of seal section, shoulder zone and thread surface of tubing by axial tensile loads are analyzed. The results show that shoulder zone is subject to most axial stresses at made-up state, which will make distribution of stresses on thread reasonable. With the increase of axial tensile loads, stresses of thread on both ends increase and on seal section and shoulder zone slightly change. The maximum stress on some thread exceed the yield limit of material when axial tensile loads exceed 400KN. Limited axial tensile loads sharply influence the contact pressures on shoulder zone while slightly on seal section. Although the maximum contact pressure on shoulder zone drop to 0 when the axial tensile load is 600KN, the maximum contact pressure on seal section will keep on a high level.

The structural optimization of roadheader conical picks based on fatigue life

2018 ◽  
Vol 09 (02) ◽  
pp. 1850013 ◽  
Author(s):  
Zhenguo Lu ◽  
Lirong Wan ◽  
Qingliang Zeng ◽  
Xin Zhang ◽  
Kuidong Gao
Keyword(s):  
Finite Element ◽  
Fatigue Life ◽  
Static Analysis ◽  
Element Model ◽  
Cutting Resistance ◽  
Strength Failure ◽  
New Type ◽  
Conical Picks ◽  
Fatigue Life Analysis ◽  
The Finite Element Model

Conical picks are the key cutting components used on roadheaders, and they are replaced frequently because of the bad working conditions. Picks did not meet the fatigue life when they were damaged by abrasion, so the pick fatigue life and strength are excessive. In the paper, in order to reduce the abrasion and save the materials, structure optimization was carried out. For static analysis and fatigue life prediction, the simulation program was proposed based on mathematical models to obtain the cutting resistance. Furthermore, the finite element models for static analysis and fatigue life analysis were proposed. The results indicated that fatigue life damage and strength failure of the cutting pick would never happen. Subsequently, the initial optimization model and the finite element model of picks were developed. According to the optimized results, a new type of pick was developed based on the working and installing conditions of the traditional pick. Finally, the previous analysis methods used for traditional methods were carried out again for the new type picks. The results show that new type of pick can satisfy the strength and fatigue life requirements.

Analysis of Packer Rubber Mechanics Properties

2014 ◽  
Vol 971-973 ◽  
pp. 380-389
Author(s):  
Jian Ning Wang ◽  
Gang Wu ◽  
Wei Yi Xie ◽  
Xin De Han ◽  
Ming Chao Gang
Keyword(s):  
Finite Element ◽  
Elastic Modulus ◽  
Constitutive Model ◽  
Contact Stress ◽  
Theoretical Basis ◽  
Element Model ◽  
Rubber Material ◽  
Bottom Hole ◽  
Sealing Performance ◽  
The Finite Element Model

Abstract: The packer rubber stress in the bottom hole is more complex. Based on constitutive model of the packer rubber material, this paper determines such parameters as model constants, Poisson's ratio of rubber materials and elastic modulus by using experimental method, to build up the finite element model of center tube-rubber cylinder-casing for the purpose of stress analysis. Finally, the distribution regularity of rubber cylinder-casing contact stress and packer setting travel distance with varying loads is concluded. The results can provide the theoretical basis for further analysis of packer rubber sealing performance.

scholarly journals Sensitivity Analysis of the Influence of Structural Parameters on Dynamic Behaviour of Highly Redundant Cable-Stayed Bridges

2013 ◽  
Vol 2013 ◽  
pp. 1-11 ◽  
Author(s):  
B. Asgari ◽  
S. A. Osman ◽  
A. Adnan
Keyword(s):  
Sensitivity Analysis ◽  
Finite Element ◽  
Finite Element Model ◽  
Model Updating ◽  
Structural Parameters ◽  
Element Model ◽  
Structural Behavior ◽  
Model Tuning ◽  
The Finite Element Model ◽  
Cable Stayed Bridges

The model tuning through sensitivity analysis is a prominent procedure to assess the structural behavior and dynamic characteristics of cable-stayed bridges. Most of the previous sensitivity-based model tuning methods are automatic iterative processes; however, the results of recent studies show that the most reasonable results are achievable by applying the manual methods to update the analytical model of cable-stayed bridges. This paper presents a model updating algorithm for highly redundant cable-stayed bridges that can be used as an iterative manual procedure. The updating parameters are selected through the sensitivity analysis which helps to better understand the structural behavior of the bridge. The finite element model of Tatara Bridge is considered for the numerical studies. The results of the simulations indicate the efficiency and applicability of the presented manual tuning method for updating the finite element model of cable-stayed bridges. The new aspects regarding effective material and structural parameters and model tuning procedure presented in this paper will be useful for analyzing and model updating of cable-stayed bridges.

Biodynamics of Human Thorax With Body Armors Subject to Bullet Impact

2001 ◽  
Author(s):  
Y. W. Kwon ◽  
J. A. Lobuono
Keyword(s):  
Experimental Data ◽  
Finite Element ◽  
Finite Element Model ◽  
Element Model ◽  
Body Armor ◽  
Projectile Impact ◽  
Human Thorax ◽  
Trachea And Bronchi ◽  
Armor System ◽  
The Finite Element Model

Abstract The objective of this study is to develop a finite element model of the human thorax with a protective body armor system so that the model can adequately determine the thorax’s biodynamical response from a projectile impact. The finite element model of the human thorax consists of the thoracic skeleton, heart, lungs, major arteries, major veins, trachea, and bronchi. The finite element model of the human thorax is validated by comparing the model’s results to experimental data obtained from cadavers wearing a protective body armor system undergoing a projectile impact.

Use of DNVGL-RP-C203 for Determining the Fatigue Capacity of Connectors

2021 ◽  
Author(s):  
Anthony Muff ◽  
Anders Wormsen ◽  
Torfinn Hørte ◽  
Arne Fjeldstad ◽  
Per Osen ◽  
...  
Keyword(s):  
Finite Element ◽  
Fatigue Testing ◽  
Experimental Testing ◽  
High Strength ◽  
Element Model ◽  
Fatigue Analysis ◽  
Full Scale ◽  
The Finite Element Model

Abstract Guidance for determining a S-N based fatigue capacity (safe life design) for preloaded connectors is included in Section 5.4 of the 2019 edition of DNVGL-RP-C203 (C203-2019). This section includes guidance on the finite element model representation, finite element based fatigue analysis and determination of the connector design fatigue capacity by use of one of the following methods: Method 1 by FEA based fatigue analysis, Method 2 by FEA based fatigue analysis and experimental testing and Method 3 by full-scale connector fatigue testing. The FEA based fatigue analysis makes use of Appendix D.2 in C203-2019 (“S-N curves for high strength steel applications for subsea”). Practical use of Section 5.4 is illustrated with a case study of a fatigue tested wellhead profile connector segment test. Further developments of Section 5.4 of C203-2019 are proposed. This included acceptance criteria for use of a segment test to validate the FEA based fatigue analysis of a full-scale preloaded connector.

Modal Analysis and Modeling of a Parallel Kinematic Machine

1999 ◽  
Author(s):  
David S. Hardage ◽  
Gloria J. Wiens
Keyword(s):  
Finite Element ◽  
Resonant Frequency ◽  
Structural Dynamics ◽  
Preliminary Data ◽  
Element Model ◽  
Parallel Kinematic Machine ◽  
Parallel Kinematic ◽  
Machine Configuration ◽  
Stiffness Characteristics ◽  
The Finite Element Model

Abstract This paper presents the results of a mini-modal survey on the Hexel Tornado 2000, a parallel kinematic machine tool located at Sandia National Laboratories, and discusses the finite element model that is used to simulate the structural dynamics of this machine. Preliminary data suggests a dependency of resonant frequency and stiffness characteristics on machine configuration.

Dynamic Analysis of a Turbocharger Centrifugal Compressor Impeller

1991 ◽  
Author(s):  
V. Ramamurti ◽  
D. A. Subramani ◽  
K. Sridhara
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Centrifugal Compressor ◽  
Element Model ◽  
Simplified Model ◽  
Cyclic Symmetry ◽  
Compressor Impeller ◽  
Cyclic Symmetric ◽  
The Finite Element Model

Abstract Stress analysis and determination of eigen pairs of a typical turbocharger compressor impeller have been carried out using the concept of cyclic symmetry. A simplified model treating the blade and the hub as isolated elements has also been attempted. The limitations of the simplified model have been brought out. The results of the finite element model using the cyclic symmetric approach have been discussed.

Sign in / Sign up

Export Citation Format

Share Document