Influence of liquid crystal cladding on light propagation in a tapered optical fiber

2019 ◽  
Author(s):  
Joanna E. Moś ◽  
Karol A. Stasiewicz ◽  
Mariusz Florek ◽  
Leszek R. Jaroszewicz
Keyword(s):  
Liquid Crystal ◽  
Optical Fiber ◽  
Light Propagation ◽  
Tapered Optical Fiber

scholarly journals Enhancement of the SPR Effect in an Optical Fiber Device Utilizing a Thin Ag Layer and a 3092A Liquid Crystal Mixture

Molecules ◽  
2021 ◽  
Vol 26 (24) ◽  
pp. 7553
Author(s):  
Joanna Korec ◽  
Karol A. Stasiewicz ◽  
Katarzyna Garbat ◽  
Leszek R. Jaroszewicz
Keyword(s):  
Refractive Index ◽  
Surface Plasmon Resonance ◽  
Liquid Crystal ◽  
Optical Fiber ◽  
Surface Plasmon ◽  
Light Propagation ◽  
Resonance Effect ◽  
Surface Plasmon Resonance Effect ◽  
Tapered Optical Fiber ◽  
Crystal Cells

This paper is a continuation of previous work and shows the enhancement of the surface plasmon resonance effect in a tapered optical fiber device. The study investigated liquid crystal cells containing a tapered optical fiber covered with a silver nanolayer, surrounded by a low refractive index liquid crystal in terms of the properties of light propagation in the taper structure. Silver films with a thickness of d = 10 nm were deposited on the tapered waist area. Measurements were performed at room temperature; liquid crystal steering voltage U from 0 to 200 V, with and without any amplitude modulation with a frequency of f = 5 Hz, and the wavelength λ ranged from 550 to 1200 nm. A significant influence of the initial arrangement of liquid crystals molecules on light propagation was observed. Three types of liquid crystal cells—orthogonal, parallel, and twist—were considered. During the measurements, resonant peaks were obtained—the position of which can also be controlled by the type of liquid crystal cells and the steering voltage. Based on the obtained results, the best parameters, such as highest peak’s width reduction, and the highest SNR value were received for twisted cells. In addition, the present work was compared with the previous work and showed the possibility of improving properties of the manufactured probes, and consequently, the surface plasmon resonance effect. In the presented paper, the novelty is mainly focused on the used materials as well as suitable changes in applied technological parameters. In contrast to gold, silver is characterized by different optic and dielectric properties, e.g., refractive index, extension coefficient, and permittivity, which results in changes in the light propagation and the SPR wavelengths.

scholarly journals SPR Effect Controlled by an Electric Field in a Tapered Optical Fiber Surrounded by a Low Refractive Index Nematic Liquid Crystal

Materials ◽  
2020 ◽  
Vol 13 (21) ◽  
pp. 4942
Author(s):  
Joanna Korec ◽  
Karol A. Stasiewicz ◽  
Leszek R. Jaroszewicz ◽  
Katarzyna Garbat
Keyword(s):  
Liquid Crystal ◽  
Electric Field ◽  
Optical Fiber ◽  
Light Propagation ◽  
Metal Layer ◽  
Fiber Surface ◽  
Fiber Axis ◽  
Initial Molecule ◽  
Tapered Optical Fiber ◽  
Spr Effect

This paper presents the influence of a thin metal layer deposition on the surface of a tapered optical fiber surrounded by a low liquid crystal, on light propagation inside the taper structure. In this research, three types of liquid crystal cells were under investigation: orthogonal, parallel, and twist. They differed by the rubbing direction of the electrodes in relation to the fiber axis determining the initial molecule arrangement inside the cell. Gold films with thickness d = 30 nm were deposited on the tapered fiber surface in the tapered waist area. Cells including a tapered optical fiber with no metallic layer were also examined and presented as a reference. All measurements were performed at room temperature for a different steering voltage U from 0 to 200 V, with and without any amplitude modulation with a frequency f = 5 Hz, and the wavelength λ range from 550 to 1200 nm. As a result, the resonant peaks were obtained, which depends on a liquid crystal cell type and steering voltage, as well. This paper shows the possibility of sensing the change of applied voltage by the constructed system. During measurements, additional effects as signal overlapping and intermodal interference were observed reducing measured voltage value. In the future, the improved, similar systems that will have a better response could be used as a sensor of factors to which liquid crystal (LC) will be sensitive, especially temperature and electric field.

scholarly journals Highly Sensitive Hydrogen Sensor Based on Palladium-Coated Tapered Optical Fiber at Room Temperature

2020 ◽  
Vol 2 (1) ◽  
pp. 8
Author(s):  
Mohammed Majeed Alkhabet ◽  
Saad Hayatu Girei ◽  
Suriati Paiman ◽  
Norhana Arsad ◽  
Mohd Adzir Mahdi ◽  
...  
Keyword(s):  
Optical Fiber ◽  
Room Temperature ◽  
Light Propagation ◽  
Cost Effective ◽  
Hydrogen Sensor ◽  
X Ray ◽  
Multimode Optical Fiber ◽  
Casting Technique ◽  
H2 Sensor ◽  
Tapered Optical Fiber

This paper describes the application of a palladium (Pd)-coated tapered optical fiber in order to develop a hydrogen (H2) sensor. A transducing channel was fabricated with multimode optical fiber (MMF) with cladding and core diameters of 125 µm and 62.5 µm, respectively, in order to enhance the evanescent field of light propagation through the fiber. The multimode optical fiber was tapered from a cladding diameter of 125 µm to a waist diameter of 20 µm, waist-length of 10 mm, and down taper and up of 5 mm, and coated with Pd using the drop-casting technique. In order to establish the palladium’s properties, various characterization techniques were applied, such as Field Emission Scanning Electron Microscopy (FESEM), Energy Dispersive X-ray (EDX), and X-ray Diffraction (XRD). The developed palladium sensor functioned reproducibly at a gas concentration of 0.125% to 1.00% H2 at room temperature in the synthetic air. In this case, the response and recovery times were 50 and 200 s, respectively. Furthermore, this study demonstrated that the production of a dependable, effective, and reproducible H2 sensor by applying a basic, cost-effective method is possible.

scholarly journals Polarization properties of nematic liquid crystal cell with tapered optical fiber

2019 ◽  
Vol 27 (4) ◽  
pp. 321-328
Author(s):  
P. Marć ◽  
K. Stasiewicz ◽  
J. Korec ◽  
L.R. Jaroszewicz ◽  
P. Kula
Keyword(s):  
Liquid Crystal ◽  
Optical Fiber ◽  
Nematic Liquid Crystal ◽  
Liquid Crystal Cell ◽  
Crystal Cell ◽  
Tapered Optical Fiber

Temperature and voltage sensing based on a tapered optical fiber device with the liquid crystal cladding

2020 ◽  
Vol 56 ◽  
pp. 102190
Author(s):  
J. Korec ◽  
K.A. Stasiewicz ◽  
L.R. Jaroszewicz ◽  
W. Piecek ◽  
P. Kula
Keyword(s):  
Liquid Crystal ◽  
Optical Fiber ◽  
Voltage Sensing ◽  
Tapered Optical Fiber

scholarly journals Temperature effect on the light propagation in a tapered optical fiber with a twisted nematic liquid crystal cladding

2019 ◽  
Vol 11 (1) ◽  
pp. 16 ◽  
Author(s):  
Joanna Korec ◽  
Karol Antoni Stasiewicz ◽  
Leszek Roman Jaroszewicz
Keyword(s):  
Liquid Crystal ◽  
Liquid Crystals ◽  
Power Spectrum ◽  
Electric Field ◽  
Optical Fiber ◽  
Fiber Optic ◽  
Optical Power ◽  
Twisted Nematic ◽  
Tapered Optical Fiber ◽  
Twisted Nematic Liquid Crystal

This paper presents the influence of temperature on optical power spectrum propagated in a tapered optical fiber with twisted nematic liquid crystal cladding (TOF-TNLCC) modulated by an electric field. The measurements were performed for a liquid crystal cell with the twisted orientation of ITO layers, filled with E7 mixture. The induced reorientation of liquid crystal (LC) n-director was measured for visible and near-infrared wavelength range [550-1100 nm] at the electric field range of 0–160 V and temperature range of 20-60 °C. The relation between temperature and the optical power spectrum of the investigated device has been established. Full Text: PDF ReferencesV.J. Tekippe, "Passive fiber optic components made by the fused biconical taper process", Proc. SPIE 1085 (1990). CrossRef T. A. Birks, Y. W. Li, The shape of fiber tapers, Journal of Lightwave Technology 10, 4 (1992). CrossRef J. Korec, K. A. Stasiewicz, O. Strzeżysz, P. Kula, L. R. Jaroszewicz, Electro-Steering Tapered Fiber-Optic Device with Liquid Crystal Cladding, Journal of Sensors 2019: 1-11 (2019) CrossRef Ch. Veilleux, J. Lapierre, J. Bures, Liquid-crystal-clad tapered fibers, Opt. Lett. 11, 733-735 (1986) CrossRef J. F Henninot, D. Louvergneaux, N. Tabiryan, M. Warenghem, Controlled leakage of a tapered optical fiber with liquid crystal cladding, Molecular Crystals and Liquid Crystals, 282, 297-308. (1996). CrossRef Y. Wang, et.al., Tapered optical fiber waveguide coupling to whispering gallery modes of liquid crystal microdroplet for thermal sensing application, Opt. Express 25, 918-926 (2017) CrossRef J. Korec, K. A. Stasiewicz, O. Strzeżysz, P. Kula, L. R. Jaroszewicz, . E. Moś, Tapered fibre liquid crystal optical device, Proc. SPIE 10681 (2018) CrossRef G. Assanto, A. Picardi, R. Barboza, A. Alberucci, Electro-optic steering of Nematicons, Phot. Lett. Poland 4, 1 (2012). CrossRef A.Ghanadzadeh Gilani, M.S. Beevers, The Electro-optical kerr effect in eutectic nematic mixtures of E7 and E8,J ournal of Molecular Liquids, 92, 3 (2001). CrossRef E. C. Mägi, P. Steinvurzel, and B.J. Eggleton, Tapered photonic crystal fibers, Opt. Express 784, 12, 5 (2004). CrossRef Y. Li and J. Lit, Transmission properties of a multimode optical-fiber taper, J. Opt. Soc. Am. A 2, (1985). CrossRef J. Korec, K. A. Stasiewicz, and L. R. Jaroszewicz, Temperature influence on optical power spectrum of the tapered fiber device with a liquid crystal cladding, Proc. SPIE 11045, 110450I (2019) CrossRef L.M. Blinov, Liquid crystals: physical properties and their possibilities in application, Advances in Liquid Crystal Research and Applications, (1981). CrossRef

scholarly journals Liquid crystal cell with a tapered optical fiber as an active element to optical applications

2019 ◽  
Vol 11 (1) ◽  
pp. 13
Author(s):  
Joanna Ewa Moś ◽  
Karol Antoni Stasiewicz ◽  
Leszek Roman Jaroszewicz
Keyword(s):  
Liquid Crystal ◽  
Optical Fiber ◽  
Optical Fibers ◽  
Fiber Optic ◽  
High Sensitivity ◽  
Single Mode ◽  
Fiber Optic Sensors ◽  
Liquid Crystal Cell ◽  
Crystal Cell ◽  
Tapered Optical Fiber

The work describes the technology of a liquid crystal cell with a tapered optical fiber as an element providing light. The tapered optical fiber with the total optical loss of 0.22 ± 0.07 dB, the taper waist diameter of 15.5 ± 0.5 μm, and the elongation of 20.4 ± 0.3 mm has been used. The experimental results are presented for a liquid crystal cell filled with a mixture 1550* for parallel orientation of LC molecules to the cross section of the taper waist. Measurement results show the influence of the electrical field with voltage in the range of 0-200 V, without, as well as with different modulation for spectral characteristics. The sinusoidal and square signal shapes are used with a 1-10 Hz frequency range. Full Text: PDF ReferencesZ. Liu, H. Y. Tam, L. Htein, M. L.Vincent Tse, C. Lu, "Microstructured Optical Fiber Sensors", J. Lightwave Technol. 35, 16 (2017). CrossRef T. R. Wolinski, K. Szaniawska, S. Ertman1, P. Lesiak, A. W. Domański, R. Dabrowski, E. Nowinowski-Kruszelnicki, J. Wojcik "Influence of temperature and electrical fields on propagation properties of photonic liquid-crystal fibres", Meas. Sci. Technol. 17, 5 (2006). CrossRef K. Nielsen, D. Noordegraaf, T. Sørensen, A. Bjarklev,T. Hansen, "Selective filling of photonic crystal fibres", J. Opt. A: Pure Appl. Opt. 7, 8 (2005). CrossRef A. A. Rifat, G. A. Mahdiraji, D. M. Chow, Y, Gang Shee, R. Ahmed, F. Rafiq, M Adikan, "Photonic Crystal Fiber-Based Surface Plasmon Resonance Sensor with Selective Analyte Channels and Graphene-Silver Deposited Core", Sensors 15, 5 (2015) CrossRef Y. Huang, Z.Tian, L.P. Sun, D. Sun, J.Li, Y.Ran, B.-O. Guan "High-sensitivity DNA biosensor based on optical fiber taper interferometer coated with conjugated polymer tentacle", Opt. Express 23, 21 (2015). CrossRef X. Wang, O. S. Wolfbeis, "The 2016 Annual Review Issue", Anal. Chem., 88, 1 (2016). CrossRef Ye Tian, W. Wang, N. Wu, X. Zou, X.Wang, "Tapered Optical Fiber Sensor for Label-Free Detection of Biomolecules", Sensors 11, 4 (2011). CrossRef O. Katsunari, Fundamentals of Optical Waveguides, (London, Academic Press, (2006). DirectLink A. K. Sharma, J. Rajan, B.D. Gupta, "Fiber-Optic Sensors Based on Surface Plasmon Resonance: A Comprehensive Review", IEEE Sensors Journal 7, 8 (2007). CrossRef C. Caucheteur, T. Guo, J. Albert, "Review of plasmonic fiber optic biochemical sensors: improving the limit of detection", Anal. Bioanal.Chem. 407, 14 (2015). CrossRef S. F. Silva L. Coelho, O. Frazão, J. L. Santos, F. X.r Malcata, "A Review of Palladium-Based Fiber-Optic Sensors for Molecular Hydrogen Detection", IEEE SENSORS JOURNAL 12, 1 (2012). CrossRef H. Waechter, J. Litman, A. H. Cheung, J. A. Barnes, H.P. Loock, "Chemical Sensing Using Fiber Cavity Ring-Down Spectroscopy", Sensors 10, 3 (2010). CrossRef S. Zhu, F. Pang, S. Huang, F.Zou, Y.Dong, T.Wang, "High sensitivity refractive index sensor based on adiabatic tapered optical fiber deposited with nanofilm by ALD", Opt. Express 23, 11 (2015). CrossRef L. Zhang, J. Lou, L. Tong, "Micro/nanofiber optical sensors", Photonics sensor 1, 1 (2011). CrossRef L.Tong, J. Lou, E. Mazur, "Single-mode guiding properties of subwavelength-diameter silica and silicon wire waveguides", Opt. Express 11, 6 (2004). CrossRef H. Moyyed, I. T. Leite, L. Coelho, J. L. Santos, D. Viegas, "Analysis of phase interrogated SPR fiber optic sensors with bimetallic layers", IEEE Sensors Journal 14, 10 (2014). CrossRef A. González-Cano, M. Cruz Navarette, Ó. Esteban, N. Diaz Herrera , "Plasmonic sensors based on doubly-deposited tapered optical fibers", Sensors 14, 3 (2014). CrossRef K. A. Stasiewicz, J.E. Moś, "Threshold temperature optical fibre sensors", Opt. Fiber Technol. 32, (2016). CrossRef L. Zhang, F. Gu, J. Lou, X. Yin, L. Tong, "Fast detection of humidity with a subwavelength-diameter fiber taper coated with gelatin film", Opt. Express 16, 17 (2008). CrossRef S.Zhu, F.Pang, S. Huang, F. Zou, Q. Guo, J. Wen, T. Wang, "High Sensitivity Refractometer Based on TiO2-Coated Adiabatic Tapered Optical Fiber via ALD Technology", Sensors 16, 8 (2016). CrossRef G.Brambilla, "Optical fibre nanowires and microwires: a review", J. Optics 12, 4 (2010) CrossRef M. Ahmad, L.L. Hench, "Effect of taper geometries and launch angle on evanescent wave penetration depth in optical fibers", Biosens. Bioelectron. 20, 7 (2005). CrossRef L.M. Blinov, Electrooptic Effects in Liquid Crystal Materials (New York, Springftianer, 1994). CrossRef L. Scolari, T.T. Alkeskjold, A. Bjarklev, "Tunable Gaussian filter based on tapered liquid crystal photonic bandgap fibre", Electron. Lett. 42, 22 (2006). CrossRef J. Moś, M. Florek, K. Garbat, K.A. Stasiewicz, N. Bennis, L.R. Jaroszewicz, "In-Line Tunable Nematic Liquid Crystal Fiber Optic Device", J. of Lightwave Technol. 36, 4 (2017). CrossRef J. Moś, K A Stasiewicz, K Garbat, P Morawiak, W Piecek, L R Jaroszewicz, "Tapered fiber liquid crystal hybrid broad band device", Phys. Scripta. 93, 12 (2018). CrossRef Ch. Veilleux, J. Lapierre, J. Bures, "Liquid-crystal-clad tapered fibers", Opt. Lett. 11, 11 (1986). CrossRef R. Dąbrowski, K. Garbat, S. Urban, T.R. Woliński, J. Dziaduszek, T. Ogrodnik, A,Siarkowska, "Low-birefringence liquid crystal mixtures for photonic liquid crystal fibres application", Liq. Cryst. 44, (2017). CrossRef S. Lacroix, R. J. Black, Ch. Veilleux, J. Lapierre, "Tapered single-mode fibers: external refractive-index dependence", Appl. Opt., 25, 15 (1986). CrossRef J.F. Henninot, D. Louvergneaux , N.Tabiryan, M. Warenghem, "Controlled Leakage of a Tapered Optical Fiber with Liquid Crystal Cladding", Mol. Cryst.and Liq.Cryst., 282, 1(1996). CrossRef

Nematic liquid crystal clad tapered optical fiber with temperature sensing properties

1990 ◽  
Vol 67 (11) ◽  
pp. 6648-6653 ◽  
Author(s):  
C. Veilleux ◽  
R. J. Black ◽  
J. Lapierre ◽  
L. W. Reeves
Keyword(s):  
Liquid Crystal ◽  
Optical Fiber ◽  
Nematic Liquid Crystal ◽  
Temperature Sensing ◽  
Sensing Properties ◽  
Tapered Optical Fiber
Sign in / Sign up

Export Citation Format

Share Document