Millimeter-resolution distributed strain sensing of concrete structures

Author(s):  
Nur Aida Abdul Rahim ◽  
Nicholas Mirabile ◽  
Maurizio Chiani ◽  
Laurent Briancon
2011 ◽  
Vol 22 (2) ◽  
pp. 191-200 ◽  
Author(s):  
Huigang Xiao ◽  
Hui Li ◽  
Jinping Ou

Cement-based strain sensors (CBCC sensor) were fabricated by taking the advantage of piezoresistivity of CB-filled CBCC. CBCC sensors were centrally embedded into concrete columns (made with C40 and C80 concretes, respectively) to monitor the strain of the columns under cyclic load and monotonic load by measuring the resistance of CBCC sensors. The comparison between the monitored results of CBCC sensors and that of traditional displacement transducers indicates that CBCC sensors have good strain-sensing abilities. Meanwhile, CBCC sensors exhibit different failure modes that break later than C40 concrete columns, but a little earlier than C80 concrete columns. Therefore, the strength-matching principle between embedded CBCC sensors and concrete columns is proposed in this article to guarantee the sensing capacity of CBCC sensors in various concrete structures. The analytical results agree well with the experimental phenomena.


2016 ◽  
Vol 78 (8-5) ◽  
Author(s):  
Hisham Mohamad ◽  
Bun Pin Tee ◽  
Koh An Ang ◽  
Mun Fai Chong

This paper describes the method of identifying typical defects of bored cast-in-situ piles when instrumenting using Distributed Optical Fiber Strain Sensing (DOFSS). The DOFSS technology is based on Brillouin Optical Time Domain Analyses (BOTDA), which has the advantage of recording continuous strain profile as opposed to the conventional discrete based sensors such as Vibrating Wire strain gauges. In pile instrumentation particularly, obtaining distributed strain profile is important when analysing the load-transfer and shaft friction of a pile, as well as detecting any anomalies in the strain regime. Features such as defective pile shaft necking, discontinuity of concrete, intrusion of foreign matter and improper toe formation due to contamination of concrete at base with soil particles, among others, may cause the pile to fail. In this study, a new technique of detecting such defects is proposed using DOFSS technology which can potentially supplement the existing non-destructive test (NDT) methods. Discussion on the performance of instrumented piles by means of maintained load test are also presented


Bautechnik ◽  
2018 ◽  
Vol 95 (9) ◽  
pp. 653-657
Author(s):  
Arne Kindler ◽  
Stephan Großwig ◽  
Thomas Pfeiffer

SPE Journal ◽  
2021 ◽  
pp. 1-10
Author(s):  
Ge Jin ◽  
Gustavo Ugueto ◽  
Magdalena Wojtaszek ◽  
Artur Guzik ◽  
Dana Jurick ◽  
...  

Summary The characteristics of hydraulic fractures in the near-wellbore region contain critical information related to the production performance of unconventional wells. We demonstrate a novel application of a fiber-optic-based distributed strain sensing (DSS) technology to measure and characterize near-wellbore fractures and perforation cluster efficiency during production. Distributed fiber-optic-based strain measurements are made based on the frequency shift of the Rayleigh scatter spectrum, which is linearly dependent on strain and temperature changes of the sensing fiber. Strain changes along the wellbore are continuously measured during the shut-in and reopening operations of a well. After removing temperature effects, extensional strain changes can be observed at locations around the perforation cluster during a shut-in period. We interpret that the observed strain changes are caused by near-wellbore fracture aperture changes caused by pressure increases within the near-wellbore fracture network. The depth locations of the measured strain changes correlate well with distributed acoustic sensing (DAS) acoustic intensity measurements that were measured during the stimulation of the well. The shape and magnitude of the strain changes differ significantly between two completion designs in the same well. Different dependencies between strain and borehole pressure can be observed at most of the perforation clusters between the shut-in and reopening periods. We assess that this new type of distributed fiber-optic measurement method can significantly improve understanding of near-wellbore hydraulic fracture characteristics and the relationships between stimulation and production from unconventional oil and gas wells.


2017 ◽  
Author(s):  
L. Schenato ◽  
M. Camporese ◽  
S. Bersan ◽  
S. Cola ◽  
A. Galtarossa ◽  
...  

2000 ◽  
Vol 27 (5) ◽  
pp. 873-879 ◽  
Author(s):  
Michael DeMerchant ◽  
Anthony Brown ◽  
Jeff Smith ◽  
Xiaoyi Bao ◽  
Theodore Bremner

Strain sensors are a valuable tool for assessing the health of structures. The University of New Brunswick, in conjunction with ISIS Canada, is developing a distributed fibre optic strain sensor based on Brillouin scattering. This sensor can provide a virtually unlimited number of measurement points using a single optical fibre. A description of the operating principles of the system is given, along with a summary of laboratory test results. Strain measurement accuracy as high as approximately ±11 µε has been demonstrated at 1 m spatial resolution. Spatial resolutions as short as 100 mm can be used, although with decreased strain measurement accuracy. Future development of the technology will include an enhancement allowing both strain and temperature to be measured simultaneously.Key words: strain sensor, fibre optics, distributed sensing, structural monitoring, Brillouin scattering.


Sign in / Sign up

Export Citation Format

Share Document