3D light interferometry investigation of ink layer formation during intaglio printing

Author(s):  
Tetiana Kyrychok ◽  
Olena Korotenko
1990 ◽  
Vol 87 ◽  
pp. 1597-1607 ◽  
Author(s):  
L Benedetti ◽  
M Borsari ◽  
C Fontanesi ◽  
G Battistuzzi Gavioli

2020 ◽  
Author(s):  
◽  
Linas Sinkevičius
Keyword(s):  

Investigation of polypyrrole layer formation peculiarities and formation of uric acid molecular imprints


Author(s):  
Dmitriy Parshin

The article gives an example of controlling the stress state parameters of additively manufactured products. The study was carried out on the basis of a developed non-classical mechanical model of the process of layer-by-layer formation of a coating of arbitrary thickness on a cylindrical substrate. The model is based on modern concepts of the mechanics of continuously growing bodies and allows one to obtain fairly simple analytical dependencies. On the basis of the latter, the problem of technological control of the evolution of contact pressure at the substrate – coating interface is solved in the article. A number of practically significant conclusions have been made.


2019 ◽  
Vol 14 (3) ◽  
Author(s):  
Saravanan S ◽  
Murugan G

This study addresses the effect of process parameters viz., loading ratio (mass of explosive/mass of flyer plate) and preset angle on dynamic bend angle, collision velocity and flyer plate velocity in dissimilar explosive cladding. In addition, the variation in interfacial microstructure and mechanical strength of aluminium 5052-stainless steel 304 explosive clads is reported. The interface exhibits a characteristic undulating interface with a continuous molten layer formation. The interfacial amplitude increases with the loading ratio and preset angle. Maximum hardness is observed at regions closer to the interface


1988 ◽  
Vol 24 (7) ◽  
pp. 381 ◽  
Author(s):  
H.N. Kheirallah ◽  
M.R.M. Rizk
Keyword(s):  

Author(s):  
Libo Wang ◽  
Martin Sharp ◽  
Benoit Rivard ◽  
Konrad Steffen

2021 ◽  
Vol 11 (4) ◽  
pp. 1891
Author(s):  
Vallery Stanishev ◽  
Nerijus Armakavicius ◽  
Chamseddine Bouhafs ◽  
Camilla Coletti ◽  
Philipp Kühne ◽  
...  

In this work we have critically reviewed the processes in high-temperature sublimation growth of graphene in Ar atmosphere using closed graphite crucible. Special focus is put on buffer layer formation and free charge carrier properties of monolayer graphene and quasi-freestanding monolayer graphene on 4H–SiC. We show that by introducing Ar at higher temperatures, TAr, one can shift the formation of the buffer layer to higher temperatures for both n-type and semi-insulating substrates. A scenario explaining the observed suppressed formation of buffer layer at higher TAr is proposed and discussed. Increased TAr is also shown to reduce the sp3 hybridization content and defect densities in the buffer layer on n-type conductive substrates. Growth on semi-insulating substrates results in ordered buffer layer with significantly improved structural properties, for which TAr plays only a minor role. The free charge density and mobility parameters of monolayer graphene and quasi-freestanding monolayer graphene with different TAr and different environmental treatment conditions are determined by contactless terahertz optical Hall effect. An efficient annealing of donors on and near the SiC surface is suggested to take place for intrinsic monolayer graphene grown at 2000 ∘C, and which is found to be independent of TAr. Higher TAr leads to higher free charge carrier mobility parameters in both intrinsically n-type and ambient p-type doped monolayer graphene. TAr is also found to have a profound effect on the free hole parameters of quasi-freestanding monolayer graphene. These findings are discussed in view of interface and buffer layer properties in order to construct a comprehensive picture of high-temperature sublimation growth and provide guidance for growth parameters optimization depending on the targeted graphene application.


Sign in / Sign up

Export Citation Format

Share Document