Three-Dimensional Surface Metrology Using A Computer Controlled Non-Contact Instrument

This paper presents two advances towards the automated three-dimensional (3-D) analysis of thick and heavily-overlapped regions in cytological preparations such as cervical/vaginal smears. First, a high speed 3-D brightfield microscope has been developed, allowing the acquisition of image data at speeds approaching 30 optical slices per second. Second, algorithms have been developed to detect and segment nuclei in spite of the extremely high image variability and low contrast typical of such regions. The analysis of such regions is inherently a 3-D problem that cannot be solved reliably with conventional 2-D imaging and image analysis methods.High-Speed 3-D imaging of the specimen is accomplished by moving the specimen axially relative to the objective lens of a standard microscope (Zeiss) at a speed of 30 steps per second, where the stepsize is adjustable from 0.2 - 5μm. The specimen is mounted on a computer-controlled, piezoelectric microstage (Burleigh PZS-100, 68/μm displacement). At each step, an optical slice is acquired using a CCD camera (SONY XC-11/71 IP, Dalsa CA-D1-0256, and CA-D2-0512 have been used) connected to a 4-node array processor system based on the Intel i860 chip.

Download Full-text

Enhancement of Heat Transfer Performance in Nuclear Fuel Rod Using Nanofluids and Surface Roughness Technique

Volume 8B: Heat Transfer and Thermal Engineering ◽

10.1115/imece2015-51476 ◽

2015 ◽

Cited By ~ 1

Author(s):

Kang Liu ◽

Titan C. Paul ◽

Leo A. Carrilho ◽

Jamil A. Khan

Keyword(s):

Heat Transfer ◽

Surface Roughness ◽

Heat Transfer Coefficient ◽

Transfer Coefficient ◽

Nuclear Fuel ◽

Three Dimensional ◽

Pressurized Water ◽

Bulk Fluid ◽

Fuel Rod ◽

Dimensional Surface

The experimental investigations were carried out of a pressurized water nuclear reactor (PWR) with enhanced surface using different concentration (0.5 and 2.0 vol%) of ZnO/DI-water based nanofluids as a coolant. The experimental setup consisted of a flow loop with a nuclear fuel rod section that was heated by electrical current. The fuel rod surfaces were termed as two-dimensional surface roughness (square transverse ribbed surface) and three-dimensional surface roughness (diamond shaped blocks). The variation in temperature of nuclear fuel rod was measured along the length of a specified section. Heat transfer coefficient was calculated by measuring heat flux and temperature differences between surface and bulk fluid. The experimental results of nanofluids were compared with the coolant as a DI-water data. The maximum heat transfer coefficient enhancement was achieved 33% at Re = 1.15 × 105 for fuel rod with three-dimensional surface roughness using 2.0 vol% nanofluids compared to DI-water.

Download Full-text

DISCRETE AND CONTINUUM APPROACHES TO THREE-DIMENSIONAL QUANTUM GRAVITY

Modern Physics Letters A ◽

10.1142/s0217732391004140 ◽

1991 ◽

Vol 06 (39) ◽

pp. 3591-3600 ◽

Cited By ~ 40

Author(s):

HIROSI OOGURI ◽

NAOKI SASAKURA

Keyword(s):

Gauge Theory ◽

Moduli Space ◽

Three Dimensional ◽

Two Dimensional ◽

Analogue Model ◽

Gauge Invariant ◽

Invariant Functions ◽

Dimensional Lattice ◽

Chern Simons ◽

Dimensional Surface

It is shown that, in the three-dimensional lattice gravity defined by Ponzano and Regge, the space of physical states is isomorphic to the space of gauge-invariant functions on the moduli space of flat SU(2) connections over a two-dimensional surface, which gives physical states in the ISO(3) Chern–Simons gauge theory. To prove this, we employ the q-analogue of this model defined by Turaev and Viro as a regularization to sum over states. A recent work by Turaev suggests that the q-analogue model itself may be related to an Euclidean gravity with a cosmological constant proportional to 1/k2, where q=e2πi/(k+2).

Download Full-text