Investigation of field-installation effects of horizontal twin-jet grouting in Shanghai soft soil deposits

2013 ◽  
Vol 50 (3) ◽  
pp. 288-297 ◽  
Author(s):  
Zhi-Feng Wang ◽  
Shui-Long Shen ◽  
Chu-Eu Ho ◽  
Yong-Hyun Kim
Keyword(s):  
Pore Water ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Soft Soil ◽  
Ground Surface ◽  
Prediction Methods ◽  
Jet Grouting ◽  
Soil Deposits ◽  
Lateral Displacements ◽  
Surface Heave

This paper presents a case study of an investigation into the responses of the surrounding ground to the horizontal twin-jet grouting method (HTJGM) in soft soil deposits of Shanghai. During the field test, the variation of pore-water pressure, lateral earth pressure, lateral displacements of the subsurface soils, and ground surface heave induced by the installation of five horizontal jet-grouted columns were monitored. The monitoring results indicate that the excess pore-water pressure reached 4 to 6 times the undrained shear strength of the soils, while maximum lateral displacements and ground surface heave were up to 80 and 17 mm, respectively. The influence range due to the installation of jet-grouted columns was between 15 and 20 times the nominal column radius. The development of prediction methods for lateral displacements and ground surface heave induced by the HTJGM installation process are presented and discussed. Results from the investigation suggest that the proposed prediction methods can be used to provide reasonable estimates of ground response and influence range of horizontal jet grouting.

Downslope movements at shallow depths related to cyclic pore-pressure changes

1993 ◽  
Vol 30 (3) ◽  
pp. 464-475 ◽  
Author(s):  
K.D. Eigenbrod
Keyword(s):  
Pore Water ◽  
Slip Surface ◽  
Pore Water Pressure ◽  
Limit Equilibrium ◽  
Water Pressure ◽  
Ground Surface ◽  
Soil Mass ◽  
Passive Resistance ◽  
Pressure Changes ◽  
Timber Piles

Slow, shallow ground movements in a slope near Yellowknife caused excessive tilting of timber piles that supported an engineering structure. To avoid damage to the structure, the pile foundations had to be replaced by rigid concrete piers that were designed to resist the forces of the moving soil mass. Downhill movements were rather slow and, during an initial inspection, were indicated only by soil that was pushed up against a series of piles on their uphill sides, while gaps had formed on their downhill sides. No open cracks or bulging was observed on the slope. A stability analysis indicated that the slope was not in a state of limit equilibrium. To obtain a better understanding of the creep movements in the slope and their effect on the rigid concrete piers, extensive instrumentation was carried out after the construction of the piers. This included slope indicators, piezometers, thermistors, and total-pressure cells against one of the concrete piers. In addition, a triaxial testing program was undertaken in which the effect of cyclic pore-water pressure changes on the long-term deformations of the shallow clay layer was investigated. From the data collected in the field and laboratory, it could be concluded that (i) tilting of the original timber piles was caused by downslope movements related to cyclic pore-water increases; (ii) the lateral soil movements increased almost linearly with depth from 2 m below the ground surface, with no indication of a slip surface; and (iii) the pressures exerted by the moving soil mass against the rigid concrete piers within the soil mass were equal to the passive resistance activated within the moving soil mass. Key words : soil creep, slope movements, soil pressures, pore-water pressures, freezing pressures, permafrost, cyclic loading.

scholarly journals Experimental Study on the Variation Law of Excess Pore Water Pressure at the Bottom of the Foundation Pit for Excavation

2020 ◽  
Vol 2020 ◽  
pp. 1-11
Author(s):  
Qizhi Hu ◽  
Qiang Zou ◽  
Zhigang Ding ◽  
Zhaodong Xu
Keyword(s):  
Pore Water ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Soft Soil ◽  
Confining Pressure ◽  
Deep Foundation ◽  
Foundation Pit ◽  
Excess Pore Water Pressure ◽  
Accurate Expression ◽  
Excess Pore

The excavation unloading of deep foundation pits in soft soil areas often produces negative excess pore water pressure. The rebound deformation of soil on the excavation surface of the foundation pit can be predicted reliably through the accurate expression of relevant variation laws. In combination with the principle of effective stress and the general equation of unidirectional seepage consolidation, an equation for calculating the rebound deformation from the bottom in the process of foundation pit excavation unloading was obtained. Additionally, a triaxial unloading test was adopted to simulate the excavation unloading processes for actual foundation pit engineering. After studying the variation law of the excess pore water pressure generated by excavation unloading, it was found that the negative excess pore water pressure increased with increasing unloading rate, while the corresponding peak value decreased with increasing confining pressure. The equation for rebound calculation was verified through a comparison with relevant measured data from actual engineering. Therefore, it is considered that the equation can reliably describe the rebound deformation law of the base. This paper aims to guide the design and construction of deep foundation pits in soft soil areas.

scholarly journals Experiment Study of Lateral Unloading Stress Path and Excess Pore Water Pressure on Creep Behavior of Soft Soil

2019 ◽  
Vol 2019 ◽  
pp. 1-9 ◽  
Author(s):  
Wei Huang ◽  
Kejun Wen ◽  
Dongsheng Li ◽  
Xiaojia Deng ◽  
Lin Li ◽  
...  
Keyword(s):  
Pore Water ◽  
Creep Behavior ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Soft Soil ◽  
Stress Path ◽  
Deviatoric Stress ◽  
Excess Pore Water Pressure ◽  
Pore Water Pressures ◽  
Excess Pore

The unloading creep behavior of soft soil under lateral unloading stress path and excess pore water pressure is the core problem of time-dependent analysis of surrounding rock deformation under excavation of soft soil. The soft soil in Shenzhen, China, was selected in this study. The triaxial unloading creep tests of soft soil under different initial excess pore water pressures (0, 20, 40, and 60 kPa) were conducted with the K0 consolidation and lateral unloading stress paths. The results show that the unloading creep of soft soil was divided into three stages: attenuation creep, constant velocity creep, and accelerated creep. The duration of creep failure is approximately 5 to 30 mins. The unloading creep behavior of soft soil is significantly affected by the deviatoric stress and time. The nonlinearity of unloading creep of soft soil is gradually enhanced with the increase of the deviatoric stress and time. The initial excess pore water pressure has an obvious weakening effect on the unloading creep of soft soil. Under the same deviatoric stress, the unloading creep of soft soil is more significant with the increase of initial excess pore water pressure. Under undrained conditions, the excess pore water pressure generally decreases during the lateral unloading process and drops sharply at the moment of unloading creep damage. The pore water pressure coefficients during the unloading process were 0.73–1.16, 0.26–1.08, and 0.35–0.96, respectively, corresponding to the initial excess pore water pressures of 20, 40, and 60 kPa.

scholarly journals Influence of Soil Structure on the Mechanical Response of Soft Soil

2018 ◽  
Vol 38 ◽  
pp. 03027
Author(s):  
Bin Bin Xu
Keyword(s):  
Yield Stress ◽  
Pore Water ◽  
Soil Structure ◽  
Mechanical Response ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Soft Soil ◽  
Before And After ◽  
Strain Relationship ◽  
Consolidation Behavior

Usually the natural sedimentary soils possess structure more or less, which makes their mechanical response much different from the fully remolded soils. In this paper, the influence of soil structure on the mechanical response such as compressibility, shear, permeability is literately reviewed. It is found that the compressibility and consolidation behavior of structured and remolded soils can be divided clearly before or after the structural yield stress. The stress-strain relationship can be divided into two segments before and after the structural yield stress. Before the yield stress, the curve is elevating and after the yield stress the curve is decreasing. The increasing rate of pore water pressure increases after the soil reached yield stress.

scholarly journals Constitutive Model of Lateral Unloading Creep of Soft Soil under Excess Pore Water Pressure

2020 ◽  
Vol 2020 ◽  
pp. 1-13
Author(s):  
Wei Huang ◽  
Kejun Wen ◽  
Xiaojia Deng ◽  
Junjie Li ◽  
Zhijian Jiang ◽  
...  
Keyword(s):  
Pore Water ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Soft Soil ◽  
Creep Model ◽  
Creep Tests ◽  
Excess Pore Water Pressure ◽  
Model Research ◽  
Creep Time ◽  
Excess Pore

Presented in this paper is a study on the lateral unloading creep tests under different excess pore water pressures. The marine sedimentary soft soil in Shenzhen, China, was selected in this study. The results show that the excess pore water pressure plays a significant role in enhancing the unloading creep of soft soil. Higher excess pore water pressure brings more obvious creep deformation of soft soil and lower ultimate failure load. Meanwhile, the viscoelastic and the viscoplastic modulus of soft soil were found to exponentially decline with creep time. A modified merchant model and a combined model of the modified merchant model and plastic elements are used to simulate the viscoelastic and the viscoplastic deformation, respectively. Therefore, a lateral unloading creep model of soft soil is developed based on the modified merchant model. The accuracy and applicability of this model were verified through identifying the parameters in the model. Research results are of particular significance to the numerical simulation of underground space excavation in soft soil areas which considers the effects of excess pore water pressure.

Calculation of Consolidation Coefficient and Percent Consolidation from Measured Pore Water Pressure of Soft Clay

2011 ◽  
Vol 250-253 ◽  
pp. 1889-1892
Author(s):  
Yong Mou Zhang ◽  
Jian Chang Zhao
Keyword(s):  
Pore Water ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Soft Soil ◽  
Soft Clay ◽  
Coefficient Of Consolidation ◽  
Consolidation Process ◽  
Consolidation Coefficient

Consolidation coefficient and percent consolidation of soft clay were calculated according to the measured pore water pressure of a project in Pudong Shanghai. Calculated coefficient of consolidation was one magnitude larger than the experimental one. This was in conformity with the actual consolidation process of dynamically-consolidated soft soil.

scholarly journals Numerical Evaluation of The Nonlinear Behavior of Soil-Pile Interaction Under The Effect of Coupled Static-Dynamic Loads

2021 ◽  
Author(s):  
Duaa Al-Jeznawi ◽  
ISMACAHYADI Mohamed Jais ◽  
Bushra S. Albusoda
Keyword(s):  
Pore Water ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Three Dimensional ◽  
Ground Surface ◽  
Frictional Resistance ◽  
Saturated Soil ◽  
Shaking Table ◽  
Physical Models ◽  
Soil Layers

Abstract Liquefaction of saturated soil layers is one of the most common causes of structural failure during earthquakes. Liquefaction occurs as a result of increasing pore water pressure, whereby the rise in water pressure occurs due to unexpected change in stress state under short-term loading, i.e., shaking during an earthquake. Thus, general failure occurs when the soil softens and eliminates its stiffness against the uplift pressure from the stability of the subsurface structure. In this case, the condition of soil strata is considered undrained because there is not enough time for the excess pore water pressure to dissipate when a sudden load is applied. To represent the non-linear characteristics of saturated sand under seismic motions in Kobe and Ali Algharbi earthquakes, the computational model was simulated using the UBCSAND model. The current study was carried out by adopting three-dimensional-based finite element models that were evaluated by shaking table tests of a single pile model erected in the saturated soil layers. The experimental data were utilized to estimate the liquefaction and seismicity of soil deposits. According to the results obtained from the physical models and simulations, this proposed model accurately simulates the liquefaction phenomenon and soil-pile response. However, there are some differences between the experiment and the computational analyses. Nonetheless, the results showed good agreement with the general trend in terms of deformation, acceleration, and liquefaction ratio. Moreover, the displacement of liquefied soil around the pile was captured by the directions of vectors generated by numerical analysis, which resembled a worldwide circular flow pattern. The results revealed that during the dynamic excitation, increased pore water pressure and subsequent liquefaction caused a significant reduction in pile frictional resistance. Despite this, positive frictional resistance was noticed through the loose sand layer (near the ground surface) until the soil softened completely. It is worth mentioning that the pile exhibited excessive settlement which may attribute to the considerable reduction, in the end, bearing forces which in turn mobilizing extra end resistance.

scholarly journals Consolidation and Deformation Characteristics of Soft Rock Foundation in Hydrological Wetland Environment

2020 ◽  
Vol 24 (2) ◽  
pp. 183-190
Author(s):  
Bin Liu ◽  
Xiugen Jiang
Keyword(s):  
Pore Water ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Soft Soil ◽  
Soft Rock ◽  
Rock Foundation ◽  
Deformation Characteristics ◽  
Soil Foundation ◽  
Soft Soil Foundation ◽  
Rock And Soil

The widespread distribution of soft rock and soft soil in hydrological wetland environment is a common geotechnical engineering problem encountered in coastal engineering construction. To solve this problem, a study method for consolidation and deformation characteristics of soft rock and soft soil foundation in hydrological wetland environment is proposed. Taking K9+280-K11+120 section along Fu-Nehe section of National Highway 111 as the research object, the consolidation and deformation characteristics and loading conditions of soft soil foundation under embankment filling load, treatment methods of soft rock foundation, stratum conditions, temperature changes and time effects are analyzed. The results show that although the wetland soft rock and soil layer is not thick, the settlement of soft rock and soil accounts for more than 80% of the total settlement. Negative temperature has a certain influence on the consolidation settlement of soft rock foundation, which is mainly manifested in the difference between the settlement process of the central separation zone and the roadbed soft soil foundation; the pore water pressure of soft rock foundation dissipates to varying degrees. According to the monitoring results of settlement and pore water pressure, bagged sand wells are more suitable for soft rock foundation engineering treatment in hydrological wetland. The research results can provide a reference for the study, calculation and design of consolidation and deformation of soft rock foundation in hydrological wetland.

scholarly journals An Analytical Continuous Upper Bound Limit Analysis of Pore Water Effect on the Tail Stability of Underwater Shield Tunnels during Construction

2020 ◽  
Vol 143 ◽  
pp. 01015
Author(s):  
Wenjie Song ◽  
Yanyong Xiang
Keyword(s):  
Pore Water ◽  
Upper Bound ◽  
Limit Analysis ◽  
Pore Water Pressure ◽  
Water Pressure ◽  
Ground Surface ◽  
Support Pressure ◽  
Tunnel Support ◽  
Transverse Stability ◽  
Upper Bound Limit Analysis

An analytical continuous upper bound limit analysis is developed to analyse the effects of seepage on the transverse stability of underwater shield tunnels. The approach is based on an analytical continuous upper bound limit analysis method for cohesive-frictional soils. It employs the complex variables solution of the displacement field due to tunnel deformation and movement, and the analytical solution of the pore water pressure field for steady state seepage due to pore water influx at the tunnel perimeter. The most critical slip line position and the minimum required tunnel support pressure are determined by using a particle swarm optimization scheme for various generic situations. The method is verified via finite element simulation and comparison with the solution from using rigid block upper bound limit analysis. The parametric analysis revealed among other things that both the infimum of the necessary tunnel support pressure and the most critical plastic zone increase when the hydraulic head at the ground surface increases, but decrease when the tunnel influx increases due to the fact that pore water pressure at the tunnel perimeter decreases with the tunnel influx.

Sign in / Sign up

Export Citation Format

Share Document