Isothermal modeling of sand–bentonite mixtures at elevated temperatures

1995 ◽  
Vol 32 (1) ◽  
pp. 78-88 ◽  
Author(s):  
B.E. Lingnau ◽  
J. Graham ◽  
N. Tanaka
Keyword(s):  
Shear Strength ◽  
Elevated Temperatures ◽  
Triaxial Compression ◽  
Friction Angle ◽  
Compression Tests ◽  
Strain Behavior ◽  
Bentonite Buffer ◽  
State Boundary ◽  
Increasing Temperature ◽  
Triaxial Compression Tests

Two models are proposed for describing the stress–strain behavior of sand–bentonite (buffer) mixtures at elevated temperatures: (1) isothermal pseudoelasticity and (2) isothermal elastic-plasticity. Data to support the models come from consolidated undrained triaxial compression tests performed on dense saturated buffer specimens at effective confining stresses up to 9.0 MPa and temperatures of 26°, 65°, and 100 °C. Measurements indicate that volumes decrease with increasing temperature if the tests are carried out under drained conditions. These trends can be modelled by a family of hardening lines in semilog compression space. Power law relationships are presented for undrained shear-strength envelopes that increase in size with an increase in temperature. The slopes of unload-reload lines, κ, in semilog compression space vary with temperature and can be related to systematic variation in the friction angle [Formula: see text]. The shear modulus G50 at 50% peak strength also depends on temperature. Several plotting techniques are used to show the existence of different state boundary surfaces for each test temperature. Key words : sand–bentonite, buffer, compression, shear strength, temperature, modelling.

Exploring the effects of nanoscale zero-valent iron (nZVI) on the mechanical properties of lead-contaminated clay

2019 ◽  
Vol 56 (10) ◽  
pp. 1395-1405 ◽  
Author(s):  
Yong-Zhan Chen ◽  
Wan-Huan Zhou ◽  
Fuming Liu ◽  
Shuping Yi
Keyword(s):  
Shear Strength ◽  
Triaxial Compression ◽  
Morphological Characteristics ◽  
Friction Angle ◽  
Zero Valent Iron ◽  
Compression Tests ◽  
Shear Tests ◽  
Nanoscale Zero Valent Iron ◽  
Triaxial Compression Tests ◽  
Oedometer Tests

Nanoscale zero-valent iron (nZVI) is a well-known efficient nanomaterial for the immobilization of heavy metals and has been widely applied in the remediation of contaminated groundwater and soils. In this study, a series of field emission scanning electron microscopy (FESEM) analyses, vane shear tests, triaxial compression tests, and oedometer tests was conducted on lead-contaminated clay using four dosages of nZVI treatment (0.2%, 1%, 5%, and 10%). The geotechnical properties, including basic index properties, stiffness, shear strength, and compressibility, were assessed after the reaction procedure. FESEM analysis was performed to explore the potential mechanisms of nZVI treatment in terms of morphological characteristics. It was found that the plasticity index decreased gradually with increasing nZVI dosage. Treating contaminated soil with nZVI caused an increase in the vane shear strength, stiffness, and friction angle. The compression index increased gradually because of the nZVI treatment. Based on the FESEM analysis, a conclusion can be deduced that larger aggregates and conjoined structures resulting from nZVI treatment can lead to the strengthening of lead-contaminated clay.

scholarly journals Triaxial Testing of Geosynthetics Reinforced Tailings with Different Reinforced Layers

Materials ◽  
2020 ◽  
Vol 13 (8) ◽  
pp. 1943
Author(s):  
Fu Yi ◽  
Changbo Du
Keyword(s):  
Triaxial Compression ◽  
Friction Angle ◽  
Confining Pressure ◽  
Test Results ◽  
Compression Tests ◽  
Strength Index ◽  
Stress Strain ◽  
High Confining Pressure ◽  
Zhang Model ◽  
Triaxial Compression Tests

To evaluate the shear properties of geotextile-reinforced tailings, triaxial compression tests were performed on geogrids and geotextiles with zero, one, two, and four reinforced layers. The stress–strain characteristics and reinforcement effects of the reinforced tailings with different layers were analyzed. According to the test results, the geogrid stress–strain curves show hardening characteristics, whereas the geotextile stress–strain curves have strain-softening properties. With more reinforced layers, the hardening or softening characteristics become more prominent. We demonstrate that the stress–strain curves of geogrids and geotextile reinforced tailings under different reinforced layers can be fitted by the Duncan–Zhang model, which indicates that the pseudo-cohesion of shear strength index increases linearly whereas the friction angle remains primarily unchanged with the increase in reinforced layers. In addition, we observed that, although the strength of the reinforced tailings increases substantially, the reinforcement effect is more significant at a low confining pressure than at a high confining pressure. On the contrary, the triaxial specimen strength decreases with the increase in the number of reinforced layers. Our findings can provide valuable input toward the design and application of reinforced engineering.

Mechanical Properties of Bentonite-Sand Mixtures Under Triaxial Stress Condition

1994 ◽  
Vol 353 ◽  
Author(s):  
M. Umedera ◽  
A. Fujiwara ◽  
N. Yasufuku ◽  
M. Hyodo ◽  
H. Murata
Keyword(s):  
Mechanical Properties ◽  
Shear Strength ◽  
Water Content ◽  
Triaxial Compression ◽  
Confining Pressure ◽  
Strength Properties ◽  
Compression Tests ◽  
Optimum Water Content ◽  
Triaxial Compression Tests ◽  
Optimum Water

AbstractA series of triaxial compression tests is being conducted under the drained condition on bentonite and sand mixtures, known as buffer, in saturated and optimum water content states to clarify the mechanical properties of the buffer.It was found that the mechanical properties of bentonite and sand mixtures are strongly influenced by water and bentonite contents: shear strength in a saturated state is less than that in an optimum water content state; shear strength decreases rapidly with increasing bentonite content. Strength properties are much dependent on confining pressure.

Influence of Water Contents on Shear Strength of Rammed Earth Wall of Earth-Building

2011 ◽  
Vol 382 ◽  
pp. 172-175
Author(s):  
Ren Wei Wu ◽  
Xing Qian Peng ◽  
Li Zhang
Keyword(s):  
Shear Strength ◽  
Water Content ◽  
Triaxial Compression ◽  
Friction Angle ◽  
World Heritage Site ◽  
Rammed Earth ◽  
Compression Tests ◽  
Rammed Earth Wall ◽  
Influence Of Water ◽  
Water Contents

As the "Fujian earth-building" have been inscribed by UNESCO in 2008 as World Heritage Site, attentions of protection about the "Fujian earth-building" has getting more and more. This article takes samples of a rammed-earth wall from Yongding earth-buildings and determines the shear strength of the samples with different water content through triaxial compression tests. The influence on shear strength of water content of rammed-earth samples is analyzed. Test results show that the shear strength of rammed-earth has much to do with the water content of the soil, the greater the water content is，the smaller the shear strength is. With water content increasing, cohesion and internal friction angle of rammed-earth were decreases, and its changing trend is of marked characteristic of stage. When water contents of rammed-earth is under some value, its cohesion changes in small ranges; when water contents of rammed-earth is over the value, its cohesion decreases with water content increasing.

scholarly journals Interpretation of undrained shear strength observed in confined triaxial compression tests on compacted clay

2021 ◽  
Author(s):  
Chee K. Wong ◽  
Martin Lun ◽  
Ron C.K. Wong
Keyword(s):  
Shear Strength ◽  
Unsaturated Soil ◽  
Water Pressure ◽  
Triaxial Compression ◽  
Undrained Shear Strength ◽  
Compacted Clay ◽  
Compression Tests ◽  
Basic Model ◽  
Triaxial Compression Tests ◽  
Undrained Shear

This paper presents an interpretation technique to quantify the effects of compaction state and matric suction on the undrained shear strength of compacted clay under confined undrained triaxial compression. This novel technique is based on the mathematical frameworks of SHANSEP (Stress History and Normalized Soil Engineering Property) method for saturated soil and BBM (Barcelona Basic model) for unsaturated soil. Test data of compacted Calgary till were analyzed and interpreted using the proposed technique. The interpretation technique is very useful in delineating the relative impacts of the factors on the behavioral trends in measured undrained shear strength. It was found that in addition to the initial compacted void ratio and suction, soil structure and failure mode exert significant influence on the undrained shear strength of compacted clay. This technique is attractive to engineering practitioners because the confined undrained compression tests (with no pore air and water pressure measurement) are much simpler and less time consuming compared to rigorous laboratory tests on unsaturated soil.

Bionic Jump Mechanism Analysis Based on Locust Hind

2013 ◽  
Vol 461 ◽  
pp. 184-190
Author(s):  
Dong Hui Chen ◽  
Heng Xie ◽  
Shao Bo Ye ◽  
Ting Wu ◽  
Xin Lu ◽  
...  
Keyword(s):  
Shear Strength ◽  
Triaxial Compression ◽  
Mechanism Analysis ◽  
Compression Tests ◽  
Fibrous Root ◽  
Factors Affecting ◽  
Complex Shear ◽  
Different Types ◽  
Soil Complex ◽  
Triaxial Compression Tests

The structure of corn stubble was complex and closely combined with the soil, so dig location and root-soil separation are the urgent problem of the manufacturing of corn stubble harvesting machinery. This paper mainly focuses on investigating the interaction principles of corn stubble and soil which by the UU triaxial compression tests. Compared the shear strength of three different types of corn root-soil complexes (vertical root, horizontal root, complex root) and pure soil, and analyzed three important factors affecting the root-soil complex shear strength, it was shown that the presence of corn fibrous root can enhance the soil shear strength and different with their layout types. It will provide a theoretical basis for the design of bionic agricultural tillage components for root- soil separation.

scholarly journals Change of soil mechanical properties due to triaxial sample size

2019 ◽  
Author(s):  
Šarūnas Skuodis ◽  
Neringa Dirgėlienė ◽  
Ieva Lekstutytė
Keyword(s):  
Shear Strength ◽  
Sample Size ◽  
Triaxial Compression ◽  
Specimen Size ◽  
Compression Tests ◽  
Shear Strength Parameters ◽  
Strength Parameters ◽  
Soil Shear Strength ◽  
Confining Pressures ◽  
Triaxial Compression Tests

Triaxial test is widely used to determine the behaviour and strength parameters of soil. Several consolidated drained triaxial compression tests were performed on two specimen sizes of sand and clay. This article investigate and compares the influence of specimen size and scale effect on the soil shear strength. The tests results show that the shear strength parameters are influenced by the clay specimen size. The results indicate that the effect of triaxial clay sample size is more significant with higher confining pressures. The second type of tests carried out on sand samples shows that sample size doesn‘t influence the results of the shear strength. Author’s show that clay analyses can be significantly affected by the choice of the specimen size used to determine shear strength parameters.

Gravel Content Effect on the Shear Strength of Clay-Gravel Mixtures

2011 ◽  
Vol 71-78 ◽  
pp. 4685-4688 ◽  
Author(s):  
Chen Wang ◽  
Chuan Ni Zhan
Keyword(s):  
Shear Strength ◽  
Internal Friction ◽  
Triaxial Compression ◽  
Constant Strain Rate ◽  
Friction Angle ◽  
Confining Pressure ◽  
Internal Friction Angle ◽  
Compression Tests ◽  
Gravel Content ◽  
Confining Pressures

Gravel content is an important factor affecting the mechanical properties of clay-gravel mixtures. To study the effects of gravel content on the shear strength of clay-gravel mixtures, constant-strain-rate drained triaxial compression tests were conducted for various mixtures. The gravel contents were 30%, 40%, 50% and 70%. The confining pressures were varied from 50kPa to 300kPa. Test results indicate that the deviator stress at failure under the same confining pressure increases with the increase in gravel content. As the gravel content in the mixtures is between 30% and 50%, the shear strength is jointly attributed by clay and gravel. An increase in gravel content results in slight increases in both the cohesion intercept and internal friction angle. At gravel content of up to 70%, the shear strength of the mixture is controlled by that of the gravel, and the cohesion intercept and the internal friction angle increase sharply.

Numerical Simulation for the Deformation of Composite Wall Insulation System

2011 ◽  
Vol 374-377 ◽  
pp. 187-190
Author(s):  
Tao Cheng
Keyword(s):  
Constitutive Model ◽  
Triaxial Compression ◽  
Constitutive Relations ◽  
Compression Tests ◽  
Stress Strain ◽  
Strain Behavior ◽  
Nonlinear Constitutive Model ◽  
Isotropic Consolidation ◽  
Composite Wall ◽  
Triaxial Compression Tests

The nonlinear constitutive relations of clay are investigated with different initial stress conditions. Two series of triaxial compression tests are performed, respectively after consolidation and isotropic consolidation. On the basis of the framework of ~ model, a uniform nonlinear constitutive model is proposed by fitting of the test data. With the average slope of the unloading-reloading curve selected as the unloading modulus, the unloading function is constructed as the loading-unloading criterion. Moreover, a comparison of the experimental stress-strain curves with the predicted results by the constitutive model is made. It is shown that the model prediction is reasonable, which can reflect the stress-strain behavior of the soil under the consolidation and isotropic consolidation conditions.

scholarly journals Consolidated Undrained Triaxial Compression Tests and Strength Criterion of Solidified Dredged Materials

2018 ◽  
Vol 2018 ◽  
pp. 1-10
Author(s):  
Jianwen Ding ◽  
Xusong Feng ◽  
Yupeng Cao ◽  
Sen Qian ◽  
Feng Ji
Keyword(s):  
Shear Strength ◽  
Water Pressure ◽  
Triaxial Compression ◽  
Strength Criterion ◽  
Undrained Shear Strength ◽  
Compression Tests ◽  
Dredged Materials ◽  
Strength Evolution ◽  
Triaxial Compression Tests ◽  
Undrained Shear

Consolidated undrained triaxial compression tests were performed to investigate the shear strength behavior of the solidified dredged materials (SDM). The variation law of deviator stress and excess pore water pressure with the increase of the applied confining pressure was investigated. It is found that the shear strength envelope is consisted of two lines, and there exists a transitional stress on the intersection point. The undrained shear strength develops slightly with the increase of applied normal stress in the preyield state. However, the undrained shear strength increases significantly in the postyield state, and the strength envelope is nearly a straight line with the extension through the origin. Based on the triaxial test data and the binary medium model, a strength criterion considering strength evolution mechanism is proposed and the relevant parameters of the strength criterion were discussed. Comparisons of the predicted results and experimental data demonstrate that the proposed strength criterion can properly describe the strength evolution rules of the SDM.

Sign in / Sign up

Export Citation Format

Share Document