Thermal characterization of micro-structured NiTi samples by 3ω scanning thermal microscopy

2008 ◽  
Vol 153 (1) ◽  
pp. 151-154 ◽  
Author(s):  
J. Gibkes ◽  
M. Chirtoc ◽  
J. S. Antoniow ◽  
R. Wernhardt ◽  
J. Pelzl
Keyword(s):  
Thermal Characterization ◽  
Scanning Thermal Microscopy ◽  
Thermal Microscopy

Thermal characterization of power devices by scanning thermal microscopy techniques

1999 ◽  
Vol 39 (6-7) ◽  
pp. 1149-1152 ◽  
Author(s):  
G.B.M. Fiege ◽  
F.-J. Niedernostheide ◽  
H.-J. Schulze ◽  
R. Barthelmeß ◽  
L.J. Balk
Keyword(s):  
Thermal Characterization ◽  
Scanning Thermal Microscopy ◽  
Power Devices ◽  
Thermal Microscopy ◽  
Microscopy Techniques

Thermal characterization of metal phthalocyanine layers using photothermal radiometry and scanning thermal microscopy methods

2017 ◽  
Vol 232 ◽  
pp. 72-78 ◽  
Author(s):  
Dominika Trefon-Radziejewska ◽  
Justyna Juszczyk ◽  
Austin Fleming ◽  
Nicolas Horny ◽  
Jean Stéphane Antoniow ◽  
...  
Keyword(s):  
Thermal Characterization ◽  
Photothermal Radiometry ◽  
Metal Phthalocyanine ◽  
Scanning Thermal Microscopy ◽  
Thermal Microscopy

scholarly journals Thermal characterization of morphologically diverse copper phthalocyanine thin layers by Scanning Thermal Microscopy

2021 ◽  
pp. 113435
Author(s):  
Dominika Trefon-Radziejewska ◽  
Justyna Juszczyk ◽  
Maciej Krzywiecki ◽  
Georges Hamaoui ◽  
Nicolas Horny ◽  
...  
Keyword(s):  
Copper Phthalocyanine ◽  
Thermal Characterization ◽  
Thin Layers ◽  
Scanning Thermal Microscopy ◽  
Thermal Microscopy

Tip-Sample Heat Transfer in Non-Contact Mode Scanning Thermal Microscopy With Wollaston Microprobes

2011 ◽  
Author(s):  
Yanliang Zhang ◽  
Liang Han ◽  
Theodorian Borca-Tasciuc
Keyword(s):  
Heat Transfer ◽  
High Spatial Resolution ◽  
Thermal Characterization ◽  
Scanning Thermal Microscopy ◽  
Solid Contact ◽  
Sample Heat ◽  
Contact Mode ◽  
Thermal Microscopy ◽  
Liquid Meniscus ◽  
Minimal Sample

Scanning thermal microscopy (SThM) is an attractive tool for high spatial resolution thermal characterization with minimal sample preparation.1 SThM measurements are usually performed in contact-mode, which entails multiple tip-sample heat transfer pathways, i.e. across air gap, liquid meniscus, and the solid contact. These hinder the quantification of the sample temperature or thermal properties or result in large uncertainties.2

Characterization of the thermal conductivity of insulating thin films by scanning thermal microscopy

2013 ◽  
Vol 44 (11) ◽  
pp. 1029-1034 ◽  
Author(s):  
Séverine Gomès ◽  
Pascal Newby ◽  
Bruno Canut ◽  
Konstantinos Termentzidis ◽  
Olivier Marty ◽  
...  
Keyword(s):  
Thin Films ◽  
Thermal Conductivity ◽  
Scanning Thermal Microscopy ◽  
Thermal Microscopy

Characterization of adhesive penetration in wood bond by means of scanning thermal microscopy (SThM)

Holzforschung ◽  
2016 ◽  
Vol 70 (4) ◽  
pp. 323-330 ◽  
Author(s):  
Deliang Xu ◽  
Yang Zhang ◽  
Handong Zhou ◽  
Yujie Meng ◽  
Siqun Wang
Keyword(s):  
Direct Contact ◽  
Phenol Formaldehyde ◽  
Transitional Zone ◽  
Transitional Region ◽  
Scanning Thermal Microscopy ◽  
Scale Level ◽  
Thermal Microscopy ◽  
Micro Scale ◽  
Adhesive Penetration

Abstract The penetration characteristics of phenol formaldehyde (PF) resin, modified by two different nanomaterials (PFmod), has been studied by means of scanning thermal microscopy (SThM). The thermal conductivity (ThC) of the two PFmod was lower than that of the cell wall (CW), but the ThC of both PF resins was basically the same. SThM imaging revealed the penetration of parts of PFmod into the CW by a ThC transitional region, which exists between the CW and the resin. In the transitional zone, the ThC changed obviously in a region about 2 μm in width. This region includes two subregions, one about 0.7 μm and another 1.3 μm in width. The first one is the interface, where PFmod and the CW are in direct contact where the ThC changes rapidly. In the second subregion, the PFmod and CW are in interaction, and ThC changes slowly. Regarding the adhesives’ penetration into the cell lumen, the ThC of the penetrating adhesive was higher than that in the glue line, and this is an indication that SThM is a useful tool to detect the differences of adhesive penetration at the micro-scale level.

Active calibration reference of minimized height for characterization of scanning thermal microscopy systems

2021 ◽  
Vol 221 ◽  
pp. 113188
Author(s):  
Paweł Janus ◽  
Dariusz Szmigiel ◽  
Andrzej Sierakowski ◽  
Maciej Rudek ◽  
Teodor Gotszalk
Keyword(s):  
Scanning Thermal Microscopy ◽  
Thermal Microscopy ◽  
Active Calibration
Sign in / Sign up

Export Citation Format

Share Document