Numerical simulation of the effect of ultrasonic impact treatment on welding residual stress

2021 ◽  
pp. 2150175
Author(s):  
Tao Mo ◽  
Jingqing Chen ◽  
Pengju Zhang ◽  
Wenqian Bai ◽  
Xiao Mu ◽  
...  
Keyword(s):  
Numerical Simulation ◽  
Residual Stress ◽  
Compressive Stress ◽  
Welded Joints ◽  
Welding Process ◽  
Residual Compressive Stress ◽  
Welding Residual Stress ◽  
304 Stainless Steel ◽  
Residual Tensile Stress ◽  
Ultrasonic Impact Treatment

Ultrasonic impact treatment (UIT) is an effective method that has been widely applied in welding structure to improve the fatigue properties of materials. It combines mechanical impact and ultrasonic vibration to produce plastic deformation on the weld joints surface, which introduces beneficial compressive residual stress distribution. To evaluate the effect of UIT technology on alleviating the residual stress of welded joints, a novel numerical analysis method based on the inherent strain theory is proposed to simulate the stress superposition of welding and subsequent UIT process of 304 stainless steel. Meanwhile, the experiment according to the process was carried out to verify the simulation of residual stress values before and after UIT. By the results, optimization of UIT application could effectively reduce the residual stress concentration after welding process. Residual tensile stress of welded joints after UIT is transformed into residual compressive stress. UIT formed a residual compressive stress layer with a thickness of about 0.13 mm on the plate. The numerical simulation results are consistent with the experimental results. The work in this paper could provide theoretical basis and technical support for the reasonable evaluation of the ultrasonic impact on residual stress elimination and mechanical properties improvement of welded joints.

Finite Element Analyses of Residual Stresses in Typical Welded Joints Used in Nuclear Power Plants and Comparisons With Experiments

2010 ◽  
Author(s):  
Dean Deng ◽  
Kazuo Ogawa ◽  
Nobuyoshi Yanagida ◽  
Koichi Saito
Keyword(s):  
Numerical Simulation ◽  
Residual Stress ◽  
Residual Stresses ◽  
Welded Joints ◽  
Nuclear Power ◽  
Power Plants ◽  
Butt Joint ◽  
Welding Residual Stress ◽  
Dissimilar Metal ◽  
Water Reactors

Recent discoveries of stress corrosion cracking (SCC) at nickel-based metals in pressurized water reactors (PWRs) and boiling water reactors (BWRs) have raised concerns about safety and integrity of plant components. It has been recognized that welding residual stress is an important factor causing the issue of SCC in a weldment. In this study, both numerical simulation technology and experimental method were employed to investigate the characteristics of welding residual stress distribution in several typical welded joints, which are used in nuclear power plants. These joints include a thick plate butt-welded Alloy 600 joint, a dissimilar metal J-groove set-in joint and a dissimilar metal girth-butt joint. First of all, numerical simulation technology was used to predict welding residual stresses in these three joints, and the influence of heat source model on welding residual stress was examined. Meanwhile, the influence of other thermal processes such as cladding, buttering and heat treatment on the final residual stresses in the dissimilar metal girth-butt joint was also clarified. Secondly, we also measured the residual stresses in three corresponding mock-ups. Finally, the comparisons of the simulation results and the measured data have shed light on how to effectively simulate welding residual stress in these typical joints.

Effect of Ultrasonic Impact Treatment on the Stress Corrosion Cracking of 304 Stainless Steel Welded Joints

2008 ◽  
Author(s):  
Gang Ma ◽  
Xiang Ling
Keyword(s):  
Residual Stress ◽  
Finite Element ◽  
Stainless Steel ◽  
Stress Corrosion ◽  
Stress Corrosion Cracking ◽  
Welded Joints ◽  
Corrosion Cracking ◽  
Coarse Grained ◽  
304 Stainless Steel ◽  
Ultrasonic Impact Treatment

High tensile weld residual stress is an important factor contributing to stress corrosion cracking (SCC). Ultrasonic impact treatment (UIT) can produce compressive stresses on the surface of welded joints that negate the tensile stresses to enhance the SCC resistance of welded joints. In the present work, X-ray diffraction method was used to obtain the distribution of residual stress induced by UIT. The results showed that UIT could cause a large compressive residual stress up to 325.9MPa on the surface of the material. A 3D finite element model was established to simulate the UIT process by using a finite element software ABAQUS. The residual stress distribution of the AISI 304 stainless steel induced by UIT was predicted by finite element analysis. In order to demonstrate the improvement of the SCC resistance of the welded joints, the specimens were immersed in boiling 42% magnesium chloride solution during SCC testing, and untreated specimen cracked after immersion for 23 hours. In contrast, treated specimens with different coverage were tested for 1000 hours without visible stress corrosion cracks. The microstructure observation results revealed that a hardened layer was formed on the surface and the initial coarse-grained structure in the surface was refined into ultrafine grains. The above results indicate that UIT is an effective approach for protecting weldments against SCC.

scholarly journals Investigation on Residual Stress Loss during Laser Peen Texturing of 316L Stainless Steel

2019 ◽  
Vol 9 (17) ◽  
pp. 3511 ◽  
Author(s):  
Kangmei Li ◽  
Yifei Wang ◽  
Yu Cai ◽  
Jun Hu
Keyword(s):  
Residual Stress ◽  
Compressive Stress ◽  
Power Density ◽  
Laser Power ◽  
Surface Deformation ◽  
Laser Power Density ◽  
Residual Compressive Stress ◽  
Laser Spot ◽  
Residual Tensile Stress ◽  
Spot Radius

Laser peen texturing (LPT) is a novelty way of surface texturing based on laser shock processing. One of the most important benefits of LPT is that it can not only fabricate surface textures but also induce residual compressive stress for the target material. However, the residual stress loss leads to partial loss of residual compressive stress and even causes residual tensile stress at the laser spot center. This phenomenon is not conducive to improving the mechanical properties of materials. In this study, a numerical simulation model of LPT was developed and validated by comparison of surface deformation with experiments. In order to investigate the phenomenon of residual stress loss quantitatively, an evaluation method of residual stress field was proposed. The effects of laser power density and laser spot radius on the residual stress, especially the residual stress loss, were systematically investigated. It is found that with the increase of laser power density or laser spot radius, the thickness of residual compressive layer in depth direction becomes larger. However, both the magnitude and the affecting zone size of residual stress loss will be increased, which implies a more severe residual stress loss phenomenon.

Temperature Field and Residual Stress Analysis of the Gear on CO2 Laser Welding Process

2011 ◽  
Vol 86 ◽  
pp. 670-673
Author(s):  
Jian Luo ◽  
Fei Li ◽  
Ke Liang Xue ◽  
De Jia Liu ◽  
Hai Wei Zhang
Keyword(s):  
Residual Stress ◽  
Temperature Field ◽  
Laser Welding ◽  
Welding Process ◽  
Welding Residual Stress ◽  
Temperature Cycle ◽  
Residual Tensile Stress ◽  
Welding Seam ◽  
Welding Temperature ◽  
Laser Welding Process

The welding technique is one of important technologies on the gear manufacturing process. The special welding temperature cycle is the basic conditions of the welding residual stress appearance in the gear. The large welding residual stress will create the large deformation after the gear welding, which will affect the gear service behavior. In this paper, the finite element method has used to simulate the gear laser welding process. The temperature field and residual stress has described. The research results show that the biggest residual compressive stress appears on the transverse direction of welding region. In the longitudinal direction, the biggest residual tensile stress appears on both sides of the welding seam line. When the laser welding power is 2.4 kW and welding speed is 20mm/s, the no apparent welding deformation’s 20CrMnSi gear can be achieved really.

Effect of Ultrasonic Impact Treatment on the Stress Corrosion Cracking of 304 Stainless Steel Welded Joints

2009 ◽  
Vol 131 (5) ◽  
Author(s):  
Xiang Ling ◽  
Gang Ma
Keyword(s):  
Residual Stress ◽  
Finite Element ◽  
Stainless Steel ◽  
Stress Corrosion ◽  
Stress Corrosion Cracking ◽  
Welded Joints ◽  
Corrosion Cracking ◽  
Coarse Grained ◽  
304 Stainless Steel ◽  
Ultrasonic Impact Treatment

High tensile weld residual stress is an important factor contributing to stress corrosion cracking (SCC). Ultrasonic impact treatment (UIT) can produce compressive stresses on the surface of welded joints that negate the tensile stresses to enhance the SCC resistance of welded joints. In the present work, X-ray diffraction method was used to obtain the distribution of residual stress induced by UIT. The results showed that UIT could cause a large compressive residual stress in access of 300 MPa on the surface of the material. A 3D finite element model was established to simulate the UIT process by using the finite element software ABAQUS. The residual stress distribution of the AISI 304 stainless steel induced by UIT was predicted by finite element analysis. In order to demonstrate the improvement of the SCC resistance of the welded joints, the specimens were immersed in boiling 42% magnesium chloride solution during SCC testing, and untreated specimen cracked after immersion for 23 h. In contrast, treated specimens with different impact duration were tested for 1000 h without visible stress corrosion cracks. The microstructure observation results revealed that a hardened layer was formed on the surface and the initial coarse-grained structure in the surface was refined into ultrafine grains. The above results indicate that UIT is an effective approach for protecting weldments against SCC.

Study on Pre-Stress Cutting of Bearing Race and Its Machined Surface State

2006 ◽  
Vol 532-533 ◽  
pp. 528-531 ◽  
Author(s):  
Bang Yan Ye ◽  
Bo Wu ◽  
Jian Ping Liu ◽  
Xiao Chu Liu ◽  
Xue Zhi Zhao
Keyword(s):  
Residual Stress ◽  
Fatigue Life ◽  
Compressive Stress ◽  
Contact Fatigue ◽  
Residual Compressive Stress ◽  
Residual Tensile Stress ◽  
Machined Surface ◽  
Residual Stress State ◽  
Bearing Race ◽  
Hard Cutting

Theoretical analysis and experiments on bearing race show that a suitable residual compressive stress on roll path of bearing race can prolong its contact fatigue life. However, residual tensile stress is often found on workpiece surface of bearing race. To actively control the residual stress state and improve fatigue life of bearing part, a new method of pre-stress hard cutting is applied. In this paper, the principle of pre-stress hard cutting for bearing race is introduced as well as the experiments on it. In the experiments, residual stress, hardness and roughness of machined surface are measured and analyzed. Moreover, micro-topography and texture characteristics of machined surface are investigated and experimental results are compared with that by grinding. It is found that we can get residual compressive stress and fine quality on machined surface of bearing race by pre-stress hard cutting and increase its productivity as well.

Welding Residual Stress in HDPE Pipes: Measurement and Numerical Simulation

2019 ◽  
Vol 141 (4) ◽  
Author(s):  
Yu Sun ◽  
Yun-Fei Jia ◽  
Muhammad Haroon ◽  
Huan-sheng Lai ◽  
Wenchun Jiang ◽  
...  
Keyword(s):  
Numerical Simulation ◽  
Residual Stress ◽  
Stress Distribution ◽  
Welded Joints ◽  
Residual Stress Distribution ◽  
Fusion Welding ◽  
Welding Residual Stress ◽  
Hole Drilling ◽  
Radial Depth ◽  
Hdpe Pipes

To understand the residual stress distribution in the welded joints of high density polyethylene (HDPE) pipes is essential to the assessment of its structural integrity. However, limited knowledge of their residual stress was available in this regard. In this paper, the hole-drilling strain-gage method was used to measure the residual stress in the welded seam of HDPE pipes, which was produced by the butt fusion welding technique. The finite element modeling using viscoelastic constitutive model with Prony series was carried out to determine the temperature field and corresponding stress field in the welding stages. The measured residual stress near the surface shows good consistency with the numerical results. It is shown that the residual stress in the hoop direction is much larger than those in the radial and axial directions. The effect of the pipe thickness on the residual stress distribution was also investigated by numerical simulation. The positions of the maximum tensile stress in the welded joints were found within the normalized depth region (the radial depth to the thickness) of 0.2 to 0.8.

scholarly journals Semi-Empirical Prediction of Residual Stress Distributions Introduced by Turning Inconel 718 Alloy Based on Lorentz Function

Materials ◽  
2020 ◽  
Vol 13 (19) ◽  
pp. 4341
Author(s):  
Huachen Peng ◽  
Penghao Dong ◽  
Xianqiang Cheng ◽  
Chen Zhang ◽  
Wencheng Tang ◽  
...  
Keyword(s):  
Residual Stress ◽  
Stress Distribution ◽  
Compressive Stress ◽  
Inconel 718 ◽  
Stress Measurement ◽  
Residual Stress Distribution ◽  
Residual Compressive Stress ◽  
Residual Tensile Stress ◽  
Semi Empirical ◽  
Prediction Approach

The residual stress of machined surface has a crucial influence on the performance of parts. It results in large deviations in terms of the position accuracy, dimension accuracy and service life. The purpose of the present study is to provide a novel semi-empirical residual stress prediction approach for turning Inconel 718. In the method, the bimodal Lorentz function was originally applied to express the residual stress distribution. A statistical model between the coefficients of the bimodal Lorentz function and cutting parameters was established by the random forest regression, in order to predict the residual stress distribution along the depth direction. Finally, the turning experiments, electrolytic corrosion peeling, residual stress measurement and correlation analysis were carried out to verify the accuracy of predicted residual stress. The results show that the bimodal Lorentz function has a great fitting accuracy. The adjusted R2 (Ad-R2) are ranging from 95.4% to 99.4% and 94.7% to 99.6% in circumferential and axial directions, respectively. The maximum and minimum errors of the surface residual tensile stress (SRTS) are 124.564 MPa and 18.082 MPa, those of the peak residual compressive stress (PRCS) are 84.649 MPa and 3.009 MPa and those of the depth of the peak residual compressive stress (DPRCS) are 0.00875 mm and 0.00155 mm, comparing three key feature indicators of predicted and simulated residual stress. The predicted residual stress is highly correlated with the measured residual stress, with correlation coefficients greater than 0.8. In the range of experimental measurement error, the research in the present work provides a quite accurate method for predicting the residual stress in turning Inconel 718, and plays a vital role in controlling the machining deformation of parts.

scholarly journals Effects of High Toughness and Welding Residual Stress for Unstable Fracture Prevention

2020 ◽  
Vol 10 (23) ◽  
pp. 8613
Author(s):  
Gyubaek An ◽  
Jeongung Park ◽  
Ilwook Han
Keyword(s):  
Residual Stress ◽  
Brittle Fracture ◽  
Compressive Stress ◽  
Fracture Prevention ◽  
Residual Compressive Stress ◽  
Welding Residual Stress ◽  
Propagation Path ◽  
Unstable Fracture ◽  
Welding Consumable ◽  
Unstable Fractures

Unstable fractures generally occur in brittle materials under low-temperature service conditions. Toughness and welding residual stress are the main factors that should be evaluated when defining a brittle crack propagation path. In this study, a rainbow welding technique was proposed and confirmed as being significantly useful in preventing unstable fractures in weld joints. The residual compressive stress in the crack front was particularly useful for decreasing the possibility of brittle fracture. The objective was to examine the effect of high welding consumable toughness welding residual stress, especially for avoiding brittle fracture through welding residual compressive stress.

Numerical Simulation of the Prestressed Laser Welding of 7075－T7451 Aluminum Alloy Sheet

2010 ◽  
Vol 431-432 ◽  
pp. 13-16 ◽  
Author(s):  
Hong Feng Wang ◽  
Dun Wen Zuo ◽  
Hong Miao ◽  
Hong Jun Wang
Keyword(s):  
Numerical Simulation ◽  
Residual Stress ◽  
Welding Process ◽  
Source Model ◽  
Alloy Sheet ◽  
Welding Residual Stress ◽  
Aluminum Alloy Sheet ◽  
Heat Source Model ◽  
Element Simulation ◽  
Input Model

The heat source model and the heat input model were built by analyzing welding process. The rationalities of model were verified by finite element simulation. The method of prestressed welding was employed in order to reduce welding residual stress. The welding residual stress would be widely impacted by imposed prestress of 90% yield strength welding. At the same time the propagation of welding heat cracking in the heat-affected zone was properly controlled by prestressed welding.

Sign in / Sign up

Export Citation Format

Share Document