Experimental Investigation and Optimization of Process Parameter for Inconel 718 Using Wire Electrical Discharge Machining

2019 ◽  
Vol 18 (03) ◽  
pp. 339-362 ◽  
Author(s):  
Anshuman Kumar ◽  
K. Vivekananda ◽  
Kumar Abhishek
Keyword(s):  
Experimental Investigation ◽  
Inconel 718 ◽  
Electrical Discharge ◽  
Electrical Discharge Machining ◽  
Process Parameter ◽  
Pareto Optimal ◽  
Wire Electrical Discharge Machining ◽  
Nsga Ii ◽  
Pulse On Time ◽  
Optimal Set

Inconel 718 is a nickel-based superalloy having high strength and low thermal conductivity. Due to its properties, wire electrical discharge machining has been selected. The paper reports an experimental investigation of Inconel 718 using zinc-coated brass wire electrode. Based on [Formula: see text], Box-Behnken design of response surface methodology has been adopted to estimate the effect of process parameter on the machining responses. Four controllable process parameters (viz., wire tension, wire speed, discharge current and pulse-on time) vary, each at three discrete levels, between parametric domains. The following machining responses, in terms of material removal rate (MRR), surface roughness ([Formula: see text]) and corner deviation ([Formula: see text]), have been investigated. Finally, an evolutionary computation method has been used based on non-dominated sorting genetic algorithm (NSGA-II) in order to find out the optimal set of solutions for rough-cutting. Experimental data have been used to develop regression models to optimize the process. The adequacy of the developed mathematical model has also been tested by the analysis of variance results. Pareto-optimal settings obtained through NSGA-II have been ranked by gray relation analysis to identify the best optimal set of solutions to avoid lengthiness and impreciseness in the judgment. Confirmation tests have been conducted for optimum machining parameter from the set of Pareto-optimal solutions for proving betterment.

Studies of kerf width and surface roughness using the response surface methodology in AA 4032–TiC composites

2021 ◽  
pp. 095440892110414
Author(s):  
TS Senthilkumar ◽  
R Muralikannan ◽  
T Ramkumar ◽  
S Senthil Kumar
Keyword(s):  
Surface Roughness ◽  
Response Surface Methodology ◽  
Response Surface ◽  
Metal Matrix ◽  
Electrical Discharge ◽  
Electrical Discharge Machining ◽  
Kerf Width ◽  
Wire Electrical Discharge Machining ◽  
Box Behnken Design ◽  
Pulse On Time

A substantially developed machining process, namely wire electrical discharge machining (WEDM), is used to machine complex shapes with high accuracy. This existent work investigates the optimization of the process parameters of wire electrical discharge machining, such as pulse on time ( Ton), peak current ( I), and gap voltage ( V), to analyze the output performance, such as kerf width and surface roughness, of AA 4032–TiC metal matrix composite using response surface methodology. The metal matrix composite was developed by handling the stir casting system. Response surface methodology is implemented through the Box–Behnken design to reduce experiments and design a mathematical model for the responses. The Box–Behnken design was conducted at a confident level of 99.5%, and a mathematical model was established for the responses, especially kerf width and surface roughness. Analysis of variance table was demarcated to check the cogency of the established model and determine the significant process. Surface roughness attains a maximum value at a high peak current value because high thermal energy was released, leading to poor surface finish. A validation test was directed between the predicted value and the actual value; however, the deviation is insignificant. Moreover, a confirmation test was handled for predicted and experimental values, and a minimal error was 2.3% and 2.12% for kerf width and surface roughness, respectively. Furthermore, the size of the crater, globules, microvoids, and microcracks were increased by amplifying the pulse on time.

Surface Roughness at Wire Electrical Discharge Machining

2015 ◽  
Vol 760 ◽  
pp. 551-556 ◽  
Author(s):  
Oana Dodun ◽  
Laurenţiu Slătineanu ◽  
Margareta Coteaţă ◽  
Vasile Merticaru ◽  
Gheorghe Nagîţ
Keyword(s):  
Surface Roughness ◽  
Empirical Model ◽  
Electrical Discharge ◽  
Electrical Discharge Machining ◽  
Roughness Parameter ◽  
Wire Electrical Discharge Machining ◽  
Power Type ◽  
Surface Roughness Parameter ◽  
Pulse On Time ◽  
Pulse Off Time

Wire electrical discharge machining is a machining method by which parts having various contours could be detached from plate workpieces. The method uses the electrical discharges developed between the workpiece and the wire tool electrode found in an axial motion, when in the work zone a dielectric fluid is recirculated. In order to highlight the influence exerted by some input process factors on the surface roughness parameter Ra in case of a workpiece made of an alloyed steel, a factorial experiment with six independent variables at two variation levels was designed and materialized. As input factors, one used the workpiece thickness, pulse on time, pulse off-time, wire axial tensile force, current intensity average amplitude defined by setting button position and travelling wire electrode speed. By mathematical processing of the experimental results, empirical models were established. Om the base of a power type empirical model, graphical representations aiming to highlight the influence of some input factors on the surface roughness parameter Ra were achieved. The power type empirical model facilitated establishing of order of factors able to exert influence on the surface roughness parameter Ra at wire electrical discharge machining.

scholarly journals Multi-Objective Optimization of Wire Electrical Discharge Machining of AL 2124/SIC Composite

2019 ◽  
Vol 9 (1) ◽  
pp. 2155-2163
Keyword(s):  
Electrical Discharge ◽  
Electrical Discharge Machining ◽  
Removal Rate ◽  
High Strength ◽  
Wire Electrical Discharge Machining ◽  
Multi Objective Optimization ◽  
Multi Objective ◽  
Predicted Values ◽  
Pulse On Time ◽  
Pulse Off Time

The growing demand for the use of high strength to weight alloys in industries for manufacturing complex structures challenges the machinability of such advanced materials. In the present investigation, the machinability of SiC particle reinforced Al 2124 composite was studied on Wire electrical discharge machining (WEDM). The process parameters namely pulse on-time (Ton), pulse off time (Toff), peak current (IP), and servo voltage (SV) were optimized by utilizing the central composite design layout. The output responses such as kerf and material removal rate (MRR) were studied in detail. The single and multi-objective optimization was studied for a combination effect using Derringer’s desirability approach and Genetic Algorithm (GA). The experimental and predicted values for each response were validated at the optimized condition. The experimental results were found in line with the predicted values. Multi objective optimization of kerf and MRR by GA showing better result compared to RSM.

Microstructural Characterization of Thermal Damage on Silicon Wafers Sliced Using Wire-Electrical Discharge Machining

2018 ◽  
Vol 140 (9) ◽  
Author(s):  
Kamlesh Joshi ◽  
Upendra Bhandarkar ◽  
Indradev Samajdar ◽  
Suhas S. Joshi
Keyword(s):  
Raman Spectroscopy ◽  
Electrical Discharge ◽  
Thermal Damage ◽  
Electrical Discharge Machining ◽  
Wafer Surface ◽  
Wire Electrical Discharge Machining ◽  
Wire Edm ◽  
Material Loss ◽  
Pulse On Time

Slicing of Si wafers through abrasive processes generates various surface defects on wafers such as cracks and surface contaminations. Also, the processes cause a significant material loss during slicing and subsequent polishing. Recently, efforts are being made to slice very thin wafers, and at the same time understand the thermal and microstructural damage caused due to sparking during wire-electrical discharge machining (wire-EDM). Wire-EDM has shown potential for slicing ultra-thin Si wafers of thickness < 200 μm. This work, therefore, presents an extensive experimental work on characterization of the thermal damage due to sparking during wire-EDM on ultra-thin wafers. The experiments were performed using Response surface methodology (RSM)-based central composite design (CCD). The damage was mainly characterized by scanning electron microscope (SEM), transmission electron microscopy (TEM), and Raman spectroscopy. The average thickness of thermal damage on the wafers was observed to be ∼16 μm. The damage was highly influenced by exposure time of wafer surface with EDM plasma spark. Also, with an increase in diameter of plasma spark, the surface roughness was found to increase. TEM micrographs have confirmed the formation of amorphous Si along with a region of fine grained Si entrapped inside the amorphous matrix. However, there were no signs of other defects like microcracks, twin boundaries, or fracture on the surfaces. Micro-Raman spectroscopy revealed that in order to slice a wafer with minimum residual stresses and very low presence of amorphous phases, it should be sliced at the lowest value of pulse on-time and at the highest value of open voltage (OV).

Analysis of Dimensional Accuracy (Over Cut) and Surface Quality (Roughness) in Electrical Discharge Machining of Inconel-718 Alloy

2019 ◽  
Vol 969 ◽  
pp. 644-649
Author(s):  
Rakesh Kumar ◽  
Anand Pandey ◽  
Pooja Sharma
Keyword(s):  
Inconel 718 ◽  
Electrical Discharge ◽  
Electrical Discharge Machining ◽  
Dimensional Accuracy ◽  
Work Piece ◽  
Tool Electrode ◽  
Affecting Factors ◽  
Inconel 718 Alloy ◽  
Electrical Discharge Drilling ◽  
Pulse On Time

Inconel-718 is a nickel based super alloy (difficult-to-cut material) used in aerospace industry. Analysis of machining performances viz. Over Cut (OC) & Surface Roughness (SR) for Inconel-718 through rotary Cu-pin tool electrode have been carried out. Peak current (Ip), pulse-on time (Ton), tool rotation (Nt) & hole depth (h) were used as input factors in Electrical Discharge Drilling (EDD) of Inconel-718 work-piece. Effect of input parameters on performance characteristics like OC & SR were found by Taguchi’s L9 (34) orthogonal array. It is reveals that Ip & h are most affecting factors that affects OC & SR. The Scanning Electron Microscope image was used to measure diameter of hole on work-piece after machining.

scholarly journals Response Surface Methodology and Artificial Neural Network-Based Models for Predicting Performance of Wire Electrical Discharge Machining of Inconel 718 Alloy

2020 ◽  
Vol 4 (2) ◽  
pp. 44
Author(s):  
Vishal Lalwani ◽  
Priyaranjan Sharma ◽  
Catalin Iulian Pruncu ◽  
Deepak Rajendra Unune
Keyword(s):  
Neural Network ◽  
Artificial Neural Network ◽  
Response Surface Methodology ◽  
Response Surface ◽  
Inconel 718 ◽  
Electrical Discharge ◽  
Electrical Discharge Machining ◽  
Wire Electrical Discharge Machining ◽  
Ann Model ◽  
Control Factors

This paper deals with the development and comparison of prediction models established using response surface methodology (RSM) and artificial neural network (ANN) for a wire electrical discharge machining (WEDM) process. The WEDM experiments were designed using central composite design (CCD) for machining of Inconel 718 superalloy. During experimentation, the pulse-on-time (TON), pulse-off-time (TOFF), servo-voltage (SV), peak current (IP), and wire tension (WT) were chosen as control factors, whereas, the kerf width (Kf), surface roughness (Ra), and materials removal rate (MRR) were selected as performance attributes. The analysis of variance tests was performed to identify the control factors that significantly affect the performance attributes. The double hidden layer ANN model was developed using a back-propagation ANN algorithm, trained by the experimental results. The prediction accuracy of the established ANN model was found to be superior to the RSM model. Finally, the Non-Dominated Sorting Genetic Algorithm-II (NSGA- II) was implemented to determine the optimum WEDM conditions from multiple objectives.

Influence of Pulse-on-Time on the Performance of Wire Electrical Discharge Machining of Ti-6Al-4V Using Zinc Coated Brass Wire

2014 ◽  
Vol 592-594 ◽  
pp. 416-420 ◽  
Author(s):  
Singaravelu D. Lenin ◽  
A. Uthirapathi ◽  
Ramana Reddy P.S. Venkata ◽  
Muthukannan Durai Selvam
Keyword(s):  
Surface Roughness ◽  
Electrical Discharge ◽  
Metal Removal ◽  
Electrical Discharge Machining ◽  
Kerf Width ◽  
Dielectric Fluid ◽  
Wire Electrical Discharge Machining ◽  
Pulse On Time ◽  
Pulse Off Time ◽  
Brass Wire

The present paper describes the influence of pulse-on-time on performance features such as Metal Removal Rate (MRR), Kerf width, Surface Roughness (SR) on cutting Titanium alloy (Ti-6Al-4V) in wire electrical discharge machining (WEDM) using zinc coated brass wire. The deionised water is used as dielectric fluid. The process parameters such as wire tension, wire speed, flushing pressure, discharge current, sparking voltage and pulse off time have kept constant at appropriate values throughout the experiment and the pulse on time is varied at nine different intervals. It was found that pulse-on-time is the most significant factor which greatly influences MRR, kerf width, and SR. It was also observed that taper at the end of cutting zone which is unavoidable occurrence for the machined part. This is due to the erosion of wire material. The surface roughness increases with increase in pulse on time also with higher rate of MRR.

Sign in / Sign up

Export Citation Format

Share Document