Fabrication of FSW Tool Pins Through Turning of H13 Tool Steel: A Comparative Analysis for Residual Stresses

2021 ◽  
pp. 1-16
Author(s):  
Ravi Butola ◽  
Ravi Pratap Singh ◽  
Naman Choudhary ◽  
K. K. S. Mer ◽  
Jitendra Bhaskar ◽  
...  
Keyword(s):  
Residual Stress ◽  
Shear Stress ◽  
Tool Steel ◽  
Compressive Residual Stress ◽  
Stress Measurement ◽  
Positive Impact ◽  
Cnc Machine Tools ◽  
Friction Stir ◽  
H13 Tool Steel ◽  
Residual Shear Stress

In the present research, measurement of residual stress induced during turning and threading operations for the fabrication of two types of pin profiled friction stir processing/welding (FSP/FSW) tools, i.e. cylindrical profiled pin tool and cylindrical threaded profiled pin tool, is being dealt with. Workpiece was chosen to be H13 tool steel with a diameter of 22[Formula: see text]mm and 110[Formula: see text]mm length. Turning and threading was done on CNC machine tools using CNMG 12404-THM uncoated tungsten carbide cutting tool. For residual stress measurement of the workpieces, an XRD-based Pulsetec[Formula: see text]-X360n portable residual stress analyzer setup was used. The experimental results show that the cylindrical pin profile tool had a compressive residual stress of [Formula: see text][Formula: see text]MPa and compressive residual shear stress of [Formula: see text][Formula: see text]MPa, while the cylindrical threaded pin profile tool had a compressive residual stress of [Formula: see text][Formula: see text]MPa (51.8% more) and compressive residual shear stress of [Formula: see text][Formula: see text]MPa (40% less). It has been concluded that due to threading operation on the cylindrical threaded pin profile, the value of residual stress is more in it, and since the stress is compressive in nature, it would have a better positive impact while doing FSP/FSW than that of the cylindrical profiled pin tool.

Simulation of Residual Stress in Lens Deposited H13 Tool Steel on Copper Substrate

2011 ◽  
Author(s):  
Tushar K. Talukdar ◽  
Liang Wang ◽  
Sergio D. Felicelli
Keyword(s):  
Residual Stress ◽  
Tool Steel ◽  
Laser Power ◽  
Copper Substrate ◽  
Scanning Speed ◽  
Temperature History ◽  
H13 Tool Steel ◽  
Scanning Strategies ◽  
Stress Accumulation ◽  
Free Edges

Solidification cracking represents a significant scientific and technical challenge in the rapid fabrication of bimetallic parts involving Cu and H13 tool steel. The main cause of the cracking formation is attributed to the residual stress accumulation, which depends on the thermal history and phase transformation during the deposition. In this research, a thermomechanical three-dimensional finite element model is developed to determine the temperature history and residual stress in Cu-H13 samples deposited by the Laser Engineered Net Shaping (LENS) process. The development of the model was carried out using the SYSWELD software package. The metallurgical transformations are taken into account using the temperature dependent material properties and the continuous cooling transformation diagram. Two different scanning strategies — alternative and unidirectional — are studied. The same model is also applied to a H13-H13 sample to compare the results. The input laser power is optimized for each layer and three different scanning speeds to maintain a steady molten pool size. It is observed that for a constant scanning speed the required laser power decreases with addition of more layers, and with the increase of scanning speed the laser power needs to be increased. The residual stress is found to be compressive near the center of the deposited wall and tensile at the free edges, which is consistent with the published experimental results in the literature. Similar stress distributions are obtained for both scanning strategies with higher stress concentration at the free edges of the interface between the substrate and the first layer. In these regions, the use of H13 substrate results in a higher stress accumulation than the Cu substrate.

RESIDUAL STRESS MEASUREMENT IN FRICTION STIR WELDS USING LASER ULTRASONICS

2009 ◽  
Author(s):  
D. Lévesque ◽  
L. Dubourg ◽  
M. Lord ◽  
M. Jahazi ◽  
A. Blouin ◽  
...  
Keyword(s):  
Residual Stress ◽  
Stress Measurement ◽  
Residual Stress Measurement ◽  
Laser Ultrasonics ◽  
Friction Stir

scholarly journals Effect of Residual Stress on the Mechanical Properties of FSW Joints with SUS409L

2018 ◽  
Vol 2018 ◽  
pp. 1-8 ◽  
Author(s):  
Yeong-Seok Lim ◽  
Sang-Hyuk Kim ◽  
Kwang-Jin Lee
Keyword(s):  
Mechanical Properties ◽  
Residual Stress ◽  
Residual Stresses ◽  
Welded Joints ◽  
Stress Measurement ◽  
Charpy Impact ◽  
Stir Zone ◽  
Hole Drilling ◽  
Friction Stir ◽  
Compressive Residual Stresses

This study was performed to investigate both the residual stress distribution and the effect of the residual stress formed at the welding region on the mechanical properties of the friction stir welded joints with 409L stainless steel sheets. Residual stress measurement with hole-drilling method; mechanical property evaluation including tensile test, Charpy impact test, and fatigue test; and microstructure observation were conducted. It has got no residual stresses to speak of at the center region of the stir zone because the stored stresses are released in the process of the dynamic recrystallization, while a small quantity of compressive residual stresses is formed at the surface region of the stir zone because of strong compression reaction by the tool shoulder. A considerable amount of compressive residual stresses is formed at the thermomechanical affected zone because of the synergy between the thermal expansion due to the heat conduction from the stir zone and mechanical compression by the tool. The formation of residual stresses shows a similar tendency between the advancing side and the retreating side. Both the mitigation of residual stress in the stir zone and the formation of compressive residual stress in the thermomechanical affected zone contribute to the improvement of the mechanical properties of the friction stir welded joints.

Stress Measurement at Fatigue Crack Tip using PSPC

1983 ◽  
Vol 27 ◽  
pp. 191-196
Author(s):  
Yasuo Yoshioka
Keyword(s):  
Residual Stress ◽  
Fatigue Crack ◽  
Stress Intensity ◽  
Compressive Residual Stress ◽  
Stress Measurement ◽  
Crack Tip ◽  
Intensity Variation ◽  
Load Cycle ◽  
Stress Distributions ◽  
Lack Of Information

The growth of fatigue crack builds up the compressive residual stress with the plastic zone in front of the crack tip. The presence of this residual stress is one of the main causes for the crack closure. The consequence of residual stress is a reduction of the crack tip stress intensity variation during a load cycle. Although this effect is well understood in a qualitative manner, it has not been completely quantified because of a lack of information about the load and residual stress distributions at the crack tip.

Influence of Deep Rolling Process Parameters on Surface Residual Stress of AA7075-T651 Aluminum Alloy Friction Stir Welded Joint

2018 ◽  
Vol 939 ◽  
pp. 23-30 ◽  
Author(s):  
Adirek Baisukhan ◽  
Wasawat Nakkiew
Keyword(s):  
Residual Stress ◽  
Aluminum Alloy ◽  
Residual Stresses ◽  
Compressive Residual Stress ◽  
Welded Joint ◽  
Rolling Process ◽  
Rolling Speed ◽  
Deep Rolling ◽  
Friction Stir ◽  
Rolling Pressure

Friction stir welding is most commonly used for joining aluminum alloy parts. After welding, residual stresses occurred in the welded joint caused by non-uniform cooling rate. Friction stir welding usually generates tensile residual stress inside the workpiece which affects the strength in addition to the fatigue life of materials. Compressive residual stress usually is beneficial and it can be introduced by mechanical surface treatment methods such as deep rolling, shot peening, laser shock peening, etc. In this research, deep rolling was used for inducing compressive residual stress on surface of friction stir welded joint. The residual stresses values were obtained from X-ray diffraction machine. Influence of three deep rolling process parameters: rolling pressure, rolling speed and rolling offset on surface residual stresses at the welded joint were investigated. Each factor had 2 levels (23 full factorial design). The statistical analysis result showed that the rolling pressure, rolling speed, rolling offset, interaction between rolling pressure and rolling speed, interaction between rolling speed and rolling offset were statistically significant factors, with the most compressive residual stress value approximately -391.6 MPa. The appropriated deep rolling process parameters on surface residual stress of AA7075-T651 aluminum alloy friction stir welded joint were 1) rolling pressure about 150 bar 2) rolling speed about 1,400 mm/min 3) rolling offset about 0.1 mm.

Improvement of Fatigue Properties in a Cast Aluminum Alloy by Roller Burnishing and Friction Stir Processing

2014 ◽  
Vol 891-892 ◽  
pp. 662-667 ◽  
Author(s):  
Yuki Nakamura ◽  
Masaki Nakajima ◽  
Hiroaki Masuda ◽  
Toshifumi Kakiuchi ◽  
Yoshihiko Uematsu
Keyword(s):  
Residual Stress ◽  
Aluminum Alloy ◽  
Friction Stir Processing ◽  
Compressive Residual Stress ◽  
Fatigue Tests ◽  
Fatigue Properties ◽  
Cast Aluminum Alloy ◽  
Cast Aluminum ◽  
Bending Fatigue ◽  
Friction Stir

Roller burnishing (RB) and friction stir processing (FSP) were applied to a cast aluminum alloy, AC4CH-T6 (equivalent to A356-T6), to improve the fatigue properties. In roller burnished specimens, Vickers hardness was increased until the depth of 60μm compared with that of the as-cast specimens, resulting in work-hardening by RB. The compressive residual stress on the surface of the roller burnished specimens was also increased from 35MPa to 132MPa. In order to investigate the effect of RB on the fatigue properties, rotary bending fatigue tests have been performed using the roller burnished and the as-cast specimens. The roller burnished specimens exhibited higher fatigue strength than the untreated specimens. It is due to the increase in hardness and compressive residual stress by RB. In addition, plane bending fatigue tests have been performed using the friction stir processed and untreated specimens. Fatigue strengths of the friction stir processed specimens were highly improved compared with untreated specimens as the results of the elimination of casting defects by FSP. However, the crack growth rates of the friction stir processed specimens were faster than those of untreated specimens. It is due to the softening of the material by heat input during the FSP.

Influence of Microshot Peening on Surface Layer Characteristics of Cold Tool Steel

2007 ◽  
Vol 561-565 ◽  
pp. 897-900 ◽  
Author(s):  
Yasunori Harada ◽  
Kenzo Fukaura ◽  
Toshinori Aoki ◽  
Daien Yokoi ◽  
Yasushi Haruna
Keyword(s):  
Residual Stress ◽  
Surface Roughness ◽  
Surface Layer ◽  
Fatigue Strength ◽  
Tool Steel ◽  
Compressive Residual Stress ◽  
Heating Furnace ◽  
Cemented Carbide ◽  
Compressed Air ◽  
New Type

Shot peening is a surface treatment and improves the performance of engineering components. More recently, a new type of microshot has been developed to enhance peening effect. In the present study, the influence of microshot peening on the surface layer characteristics of cold tool steel was investigated. In the experiment, the microshot peening apparatus with a heating furnace was produced experimentally. The projective method of the microshot was a compressed air type. The peening microshots of 0.1mm diameter were cemented carbide and the workpiece was commercially cold tool steel SKD11. Surface roughness, compressive residual stress, and hardness in the peened workpiece were measured. The effect of microshot peening on the fatigue strength of cold tool steel was also examined. The use of hard microshot such as cemented carbide was found to cause a significantly enhanced peening effect for cold tool steel.

Residual Stress Measurement in 304 Stainless Steel Weld Overlay Pipes

1996 ◽  
Vol 118 (1) ◽  
pp. 135-142 ◽  
Author(s):  
Hung-Ju Yen ◽  
Mark Ching-Cheng Lin ◽  
Lih-Jin Chen
Keyword(s):  
Residual Stress ◽  
Compressive Residual Stress ◽  
Stress Measurement ◽  
Residual Stress Distribution ◽  
304 Stainless Steel ◽  
Steel Weld ◽  
Weld Overlay ◽  
Stainless Steel Weld ◽  
Inner Surface ◽  
Welded Pipe

Welding overlay repair (WOR) is commonly employed to rebuild piping systems suffering from intergranular stress corrosion cracking (IGSCC). To understand the effects of this repair, it is necessary to investigate the distribution of residual stresses in the welded pipe. The overlay welding technique must induce compressive residual stress at the inner surface of the welded pipe to prevent of IGSCC. To understand the bulk residual stress distribution, the stress profile as a function of location within wall is examined. In this study the full destructive residual stress measurement technique—a cutting and sectioning method—is used to determine the residual stress distribution. The sample is type 304 stainless steel weld overlay pipe with an outside diameter of 267 mm. A pipe segment is cut from the circular pipe; then a thin layer is removed axially from the inner to the outer surfaces until further sectioning is impractical. The total residual stress is calculated by adding the stress relieved by cutting the section away to the stress relieved by axially sectioning. The axial and hoop residual stresses are compressive at the inner surface of the weld overlay pipe. Compressive stress exists not only at the surface but is also distributed over most of the pipe’s cross section. On the one hand, the maximum compressive hoop residual stress appears at the pipe’s inner surface. The magnitude approaches the yield strength of the material; the compressive stress exists from the inner surface out to 7.6 mm (0.3 in.) radially. On the other hand, compressive axial residual stress begins at depths greater than 2.5 mm (0.1 in.); its maximum value is located at 10.7 mm (0.42 in.) with magnitude close to four-tenths of yield strength. The thermal-mechanical induced crack closure from significant compressive residual stress is discussed. This crack closure can thus prevent IGSCC very effectively.

Sign in / Sign up

Export Citation Format

Share Document