scholarly journals Late-Age Properties of Concrete with Different Binders Cured under 45°C at Early Ages

2017 ◽  
Vol 2017 ◽  
pp. 1-13 ◽  
Author(s):  
Hu Jin
Keyword(s):  
High Temperature ◽  
Fly Ash ◽  
Blast Furnace Slag ◽  
Reference Sample ◽  
Chloride Ions ◽  
Curing Temperature ◽  
Cement Concrete ◽  
Fly Ash Concrete ◽  
Granulate Blast Furnace Slag ◽  
Furnace Slag

It is commonly accepted that high curing temperature (near 60°C or above) results in reduced mechanical properties and durability of concrete compared to normal curing temperature. The internal temperature of concrete structures at early ages is not so high as 60°C in many circumstances. In this paper, concretes were cured at 45°C at early ages and their late-age properties were studied. The concrete cured at 20°C was employed as the reference sample. Four different concretes were used: plain cement concrete, concrete containing fly ash, concrete containing ground granulate blast furnace slag (GGBS), and concrete containing silica fume. The results show that, for each concrete, high-temperature curing after precuring does not have any adverse effect on the nonevaporable water content, compressive strength, permeability to chloride ions, and the connected porosity of concrete at late ages compared with standard curing. Additionally, high-temperature curing improves the late-age properties of concrete containing fly ash and GGBS.

scholarly journals Influence of Curing Time on the Drying Shrinkage of Concretes with Different Binders and Water-to-Binder Ratios

2017 ◽  
Vol 2017 ◽  
pp. 1-10 ◽  
Author(s):  
Jun Yang ◽  
Qiang Wang ◽  
Yuqi Zhou
Keyword(s):  
Blast Furnace ◽  
Fly Ash ◽  
Blast Furnace Slag ◽  
Drying Shrinkage ◽  
Mineral Admixture ◽  
Curing Time ◽  
Cement Concrete ◽  
Fly Ash Concrete ◽  
Granulated Blast Furnace Slag ◽  
Furnace Slag

Plain cement concrete, ground granulated blast furnace slag (GGBS) concrete, and fly ash concrete were designed. Three wet curing periods were employed, which were 2, 5, and 8 days. The drying shrinkage values of the concretes were measured within 1 year after wet curing. The results show that the increasing rate of the drying shrinkage of concrete containing a mineral admixture at late age is higher than that of plain cement concrete regardless of the wet curing time. With the reduction of wet curing time, the increment of total drying shrinkage of concrete decreases with the decrease of the W/B ratio. The negative effects on the drying shrinkage of fly ash concrete due to the reduction of the wet curing time are much more obvious than those of GGBS concrete and plain cement concrete. Superfine ground granulated blast furnace slag (SGGBS) can reduce the drying shrinkage of GGBS concrete and fly ash concrete when the wet curing time is insufficient.

Resistance Performance of Concrete Using both Blast Furnace Slag Cement and Fly Ash against Chloride Attack and Carbonation

2015 ◽  
Vol 1110 ◽  
pp. 271-276
Author(s):  
Kenta Miura ◽  
Takao Ueda ◽  
Masayuki Tsukagoshi
Keyword(s):  
Blast Furnace ◽  
Fly Ash ◽  
Pore Structure ◽  
Blast Furnace Slag ◽  
Chloride Ions ◽  
Slag Cement ◽  
Fly Ash Concrete ◽  
Chloride Attack ◽  
Resistance Performance ◽  
Furnace Slag

From the viewpoint of effective utilization of industrial wastes and reduction of CO2 emission, the use of concrete mixed with blast furnace slag and fly ash has been promoted. However, the durability of fly ash concrete using blast furnace slag cement has not been clarified enough. About chloride attack, the resistance against the penetration of chloride ions could be improved due to the dense pore structure formed by the synegetic effect of mixing both ground granulated blast-furnace slag and fly ash into concrete. In this study, resistance performance of concrete using both blast furnace slag cement and fly ash against chloride attack and carbonation was experimentally investigated. The relationship between such resistance performance and pore structure of the concrete was also examined. As a result, the combination of blast furnace slag cement and fly ash type II resulted in the decrease of pore volume over 50 nm in the diameter and reduction of the apparent diffusion coefficient of chloride ion, but the resistance performance against carbonation of the concrete was lower than the case of the normal fly ash concrete.

Reviews on the Geopolymer Materials for Coating Application

2012 ◽  
Vol 626 ◽  
pp. 958-962 ◽  
Author(s):  
Yahya Zarina ◽  
Mohd Mustafa Al Bakri Abdullah ◽  
H. Kamarudin ◽  
I. Khairul Nizar ◽  
Rafiza Abd Razak
Keyword(s):  
Blast Furnace ◽  
High Temperature ◽  
Fly Ash ◽  
Blast Furnace Slag ◽  
Coating Application ◽  
Existing Structures ◽  
Granulated Blast Furnace Slag ◽  
Temperature Exposure ◽  
New Applications ◽  
Furnace Slag

The application of geopolymer has been expand in many areas where before this it only used for the production of cement and concrete. One of the new applications of geopolymer is for coating. Metakaolin, fly ash and granulated blast furnace slag has been used as source for the production of geopolymer coating. The result for the geopolymer coating showed that it can prevent corrosion in seawater structure, high bonding strength between existing structures (OPC concrete), lower water permeability and also stable during high temperature exposure.

Chloride Ions Penetration Resistance of New-Old Concrete

2011 ◽  
Vol 366 ◽  
pp. 518-521
Author(s):  
Zhi Min He ◽  
Jun Zhe Liu
Keyword(s):  
Blast Furnace ◽  
Fly Ash ◽  
Beneficial Effect ◽  
Blast Furnace Slag ◽  
Penetration Resistance ◽  
Chloride Ions ◽  
Mineral Admixtures ◽  
Compound System ◽  
Astm C1202 ◽  
Furnace Slag

By use of ASTM C1202, this paper studied the influence of mineral admixtures on the chloride ions penetration resistance of the new-old concrete compound system. The results indicate that the performance of new-old concrete exert significant influence on the new-old concrete compound system. The addition of mineral admixtures improve the permeability properties of new-old concrete. Adding fly ash(FA) require a relatively longer time to get its beneficial effect. When 30% weight of cement is replaced by 10% FA and 20% ground blast furnace slag(GGBFS), the inclusion of 30% mineral admixtures significantly improve the chloride ions penetration resistance properties of the new-old concrete compound system at 28 days and 180 days.

Effect of Mineral Admixtures and Water/Binder Ratios on the Resistance to the Chloride Ions Penetration into Concrete

2011 ◽  
Vol 99-100 ◽  
pp. 758-761
Author(s):  
Yan Jun Hu ◽  
Yan Liang Du
Keyword(s):  
Blast Furnace ◽  
Fly Ash ◽  
Silica Fume ◽  
Blast Furnace Slag ◽  
Chloride Ion ◽  
Test Methods ◽  
Chloride Ions ◽  
Mineral Admixtures ◽  
Chloride Permeability ◽  
Furnace Slag

In this study, concrete prisms were made with three mineral admixtures: fly ash, blast furnace slag or silica fume and with three water-to-binder ratios(w/b). Chloride penetration was measured by the rapid chloride permeability test (RCPT)-ASTM C1202, 150-days ponding test and alternate wetting and drying test by cyclic loading with salt solution and oven drying, and the results by the three test methods were compared. This paper discussed the effects of mineral admixtures and w/b on the concrete chloride permeability. Blending concrete with blast furnace slag, fly ash or silica fume was beneficial with regard to the resistance against chloride ion penetration. Concrete specimens with lower w/b showed lower chloride permeability.

scholarly journals Utilization of Industrial By-Products/Waste to Manufacture Geopolymer Cement/Concrete

2021 ◽  
Vol 13 (2) ◽  
pp. 873
Author(s):  
Numanuddin M. Azad ◽  
S.M. Samindi M.K. Samarakoon
Keyword(s):  
Mechanical Properties ◽  
Blast Furnace ◽  
Fly Ash ◽  
Blast Furnace Slag ◽  
Industrial Waste ◽  
Cement Concrete ◽  
Granulated Blast Furnace Slag ◽  
Geopolymer Cement ◽  
Furnace Slag ◽  
By Products

There has been a significant movement in the past decades to develop alternative sustainable building material such as geopolymer cement/concrete to control CO2 emission. Industrial waste contains pozzolanic minerals that fulfil requirements to develop the sustainable material such as alumino-silicate based geopolymer. For example, industrial waste such as red mud, fly ash, GBFS/GGBS (granulated blast furnace slag/ground granulated blast furnace slag), rice husk ash (RHA), and bagasse ash consist of minerals that contribute to the manufacturing of geopolymer cement/concrete. A literature review was carried out to study the different industrial waste/by-products and their chemical composition, which is vital for producing geopolymer cement, and to discuss the mechanical properties of geopolymer cement/concrete manufactured using different industrial waste/by-products. The durability, financial benefits and sustainability aspects of geopolymer cement/concrete have been highlighted. As per the experimental results from the literature, the cited industrial waste has been successfully utilized for the synthesis of dry or wet geopolymers. The review revealed that that the use of fly ash, GBFS/GGBS and RHA in geopolymer concrete resulted high compressive strength (i.e., 50 MPa–70 MPa). For high strength (>70 MPa) achievement, most of the slag and ash-based geopolymer cement/concrete in synergy with nano processed waste have shown good mechanical properties and environmental resistant. The alkali-activated geopolymer slag, red mud and fly ash based geopolymer binders give a better durability performance compared with other industrial waste. Based on the sustainability indicators, most of the geopolymers developed using the industrial waste have a positive impact on the environment, society and economy.

Sign in / Sign up

Export Citation Format

Share Document