scholarly journals Fracture Strength and Stress Distribution in Premolars Restored with Cast Post-and-Cores or Glass-Fiber Posts Considering the Influence of Ferule

2019 ◽  
Vol 2019 ◽  
pp. 1-7 ◽  
Author(s):  
Atais Bacchi ◽  
Ricardo Armini Caldas ◽  
Daniel Schmidt ◽  
Mauricio Detoni ◽  
Matheus Albino Souza ◽  
...  
Keyword(s):  
Stress Distribution ◽  
Glass Fiber ◽  
Fracture Strength ◽  
Lower Percentage ◽  
Element Analysis ◽  
Mean Values ◽  
Failure Patterns ◽  
Fiber Posts ◽  
Glass Fiber Posts ◽  
Post And Core

Objectives. The aim of this study was to evaluate the influence of ferule and the post type on the fracture strength and stress distribution in premolars. Materials and Methods. Forty human mandibular premolars were decoronated, allocated in four groups, and restored as follows: CPC-NF: cast post-and-core and absence of ferule; CPC-F: cast post-and-core and presence of ferule; FPC-NF: glass-fiber posts and absence of ferule; FPC-F: glass-fiber posts and presence of ferule. The fracture strength (FS) and failure patterns were evaluated. Finite element analysis (FEA) evaluated the stress distribution. Results. FS did not differ between CPCs and FPC either in presence or in absence of ferule. The presence of ferule increased FS with both post types. Mean values of FS for ferule groups were higher than functional or parafunctional loads reported in literature, which was not the case for FPC-NF when compared to parafunctional loads. FEA with a functional load showed slightly higher compressive stresses in dentin in the group CPC-NF, which was much lower than the compressive strength of dentin. Lower percentage of catastrophic failures was observed in nonferule groups irrespective of post type, which was explained by the stress concentration in the cervical root region when FEA with the FS load was simulated. Conclusion. Ferule effect was shown to be more important than post type in the analysis. Both posts showed potential to withstand functional loads irrespective of presence of ferule. However, the mean FS was lower than parafunctional loads for FPC in the absence of ferule.

Influence of Prefabricated Post Material on Restored Teeth: Fracture Strength and Stress Distribution

2006 ◽  
Vol 31 (1) ◽  
pp. 47-54 ◽  
Author(s):  
A. Barjau-Escribano ◽  
J. L. Sancho-Bru ◽  
L. Forner-Navarro ◽  
P. J. Rodríguez-Cervantes ◽  
A. Pérez-González ◽  
...  
Keyword(s):  
Elastic Modulus ◽  
Stress Distribution ◽  
Glass Fiber ◽  
Success Rate ◽  
Failure Mode ◽  
Fracture Strength ◽  
Clinical Relevance ◽  
Fiber Posts ◽  
Glass Fiber Posts

Clinical Relevance When restoring teeth, a higher restoring success rate can be achieved by using posts with an elastic modulus similar to that of dentin and a core, with equal or higher strength, such as glass fiber posts. Moreover, the failure mode for these post systems will allow for further repair.

Analysis of Dentinal Stress Distribution of Maxillary Central Incisors Subjected to Various Post-and-core Applications

2006 ◽  
Vol 31 (1) ◽  
pp. 89-96 ◽  
Author(s):  
S. Toksavul ◽  
M. Zor ◽  
M. Toman ◽  
M. A. Güngör ◽  
I. Nergiz ◽  
...  
Keyword(s):  
Stress Concentration ◽  
Stress Distribution ◽  
Glass Fiber ◽  
Clinical Relevance ◽  
Zirconia Ceramic ◽  
Fiber Posts ◽  
Glass Fiber Posts ◽  
Post And Core ◽  
Fea Analysis ◽  
Cervical Area

Clinical Relevance According to FEA analysis, under a simulated occlusal load, the cervical area of endodontically treated and crowned maxillary central incisors was the most stress concentrated area. Zirconia ceramic posts create slightly less dentinal stress concentration than titanium and glass-fiber posts.

CAD/CAM Milled Glass Fiber Posts: Adaptation and Mechanical Behavior in Flared Root Canals

2021 ◽  
Author(s):  
MER Gama ◽  
GS Balbinot ◽  
GC Ferreira ◽  
EG Mota ◽  
VCB Leitune ◽  
...  
Keyword(s):  
Bond Strength ◽  
Glass Fiber ◽  
Fiber Post ◽  
Root Canals ◽  
Fiber Posts ◽  
Cad Cam ◽  
Glass Fiber Posts ◽  
Glass Fiber Post ◽  
Post And Core ◽  
Push Out

SUMMARY This study aimed to evaluate the cementation and mechanical behavior of flared root canals restored with CAD/CAM milled glass fiber post-and-core systems. Sixty-six endodontically treated human canines with a flared root canal were divided into three different groups according to the type of post: GPF received prefabricated posts; GREL received relined glass fiber posts, and GMILLED received CAD/CAM milled glass fiber posts. Cementation was performed with self-adhesive resin cement. The samples were submitted to x-ray microcomputed tomography analysis for the analysis of voids and gaps. The roots were sectioned and submitted to the push-out bond strength test. The load-to-fracture was evaluated in post-and-core systems. GMILLED presented lower void and lower gap volumes when compared to GPF and GREL. On the load-to-fracture test, GREL presented statistically significant higher values than GMILLED. GPF values had no statistically significant difference from the two other groups. On the push-out bond strength test, GPF presented statistically significant lower values when compared to GREL and GMILLED. The most common failure pattern was between dentin and cement in all groups. CAD/CAM milled glass fiber post-and-core systems presented an enhanced adaptation of glass fiber posts to flared root canal systems. Their results were comparable to relined posts in bond strength, while load-to-fracture-results for GMILLED were lower than those for GPF.

The effect of glass fiber posts and ribbons on the fracture strength of teeth with flared root canals restored using composite resin post and cores

2018 ◽  
Vol 62 (1) ◽  
pp. 97-103 ◽  
Author(s):  
Mariko Kubo ◽  
Wataru Komada ◽  
Shiho Otake ◽  
Tasuku Inagaki ◽  
Satoshi Omori ◽  
...  
Keyword(s):  
Glass Fiber ◽  
Fracture Strength ◽  
Composite Resin ◽  
Root Canals ◽  
Fiber Posts ◽  
Glass Fiber Posts

Fatigue surviving, fracture resistance, shear stress and finite element analysis of glass fiber posts with different diameters

2015 ◽  
Vol 43 ◽  
pp. 69-77 ◽  
Author(s):  
Vinícius Felipe Wandscher ◽  
César Dalmolin Bergoli ◽  
Ariele Freitas de Oliveira ◽  
Osvaldo Bazzan Kaizer ◽  
Alexandre Luiz Souto Borges ◽  
...  
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Shear Stress ◽  
Glass Fiber ◽  
Fracture Resistance ◽  
Element Analysis ◽  
Fiber Posts ◽  
Glass Fiber Posts ◽  
Different Diameters

scholarly journals Stress Generated by Customized Glass Fiber Posts and Other Types by Photoelastic Analysis

2015 ◽  
Vol 26 (3) ◽  
pp. 222-227 ◽  
Author(s):  
Kátia Bosso ◽  
Alcides Gonini Júnior ◽  
Ricardo Danil Guiraldo ◽  
Sandrine Bittencourt Berger ◽  
Murilo Baena Lopes
Keyword(s):  
Glass Fiber ◽  
High Stress ◽  
Resin Cement ◽  
Fiber Post ◽  
Tooth Structure ◽  
Biomechanical Behavior ◽  
Fiber Posts ◽  
Glass Fiber Posts ◽  
Glass Fiber Post ◽  
Post And Core

Endodontic posts are necessary to provide adequate retention and support when no sufficient remaining structure is available to retain the core. There are different materials and techniques to construct post-and-core, but there is no consensus about which one promotes better stress distribution on the remaining tooth structure. This study aimed to quantify and evaluate the distribution of stress in the root produced by customized glass fiber posts compared to different endodontic posts. Twenty-five simulated roots from photoelastic resin were made and divided into 5 groups: CPC, cast post-and-core; SP, screw post; CF, carbon fiber post; GF, glass fiber post; and CGF, customized glass fiber post. After cementing CPC and SP posts with zinc phosphate cement, and CF, GF and CGF posts with resin cement, resin cores were made for groups 2-5. Specimens were evaluated with vertical or 45° oblique loading. To analyze the fringes, the root was divided into 6 parts: palatal cervical, palatal middle, palatal apical, vestibular cervical, vestibular middle, and vestibular apical. The formed fringes were photographed and quantified. Data were recorded and subjected to two-way ANOVA and Tukey's test (5%). SP (1.95±0.60) showed higher stress (p<0.05) compared to the others (CPC-0.52±0.74; CF-0.50±0.75, GF-0.23±0.48 and CGF-0.45±0.83). All posts showed high stress in apical third (CPC-1.40±0.65; SP-2.30±0.44, CF-1.80±0.45, GF-1.20±0.45, CGF-1.70±1.03) Low stress was found in cervical third (CPC-0.20±0.45; CF-0.00±0.00, GF-0.00±0.00, CGF-0.00±0.00), except by SP (1.90±0.65), which showed statistical difference (p<0.05). Customized post showed high stress concentration at the root and conventional glass fiber posts showed more favorable biomechanical behavior.

scholarly journals Three-Year Follow Up of Customized Glass Fiber Esthetic Posts

2011 ◽  
Vol 05 (01) ◽  
pp. 107-112 ◽  
Author(s):  
Rogério Goulart da Costa ◽  
Eduardo Christiano Caregnatto de Morais ◽  
Moira Pedroso Leão ◽  
Márcio José Fraxino Bindo ◽  
Edson Alves Campos ◽  
...  
Keyword(s):  
Glass Fiber ◽  
Root Canal ◽  
Fiber Glass ◽  
Endodontically Treated Teeth ◽  
Core System ◽  
Fiber Posts ◽  
Suitable Treatment ◽  
Glass Fiber Posts ◽  
Post And Core

ABSTRACTCustomized glass fiber posts that is well adjusted into the root canal and have mechanical properties similar to those of dentin may be a suitable treatment for severely compromised endodontically treated teeth. This article reports a 3-year follow up of severely damaged endodontically treated teeth restored with unidirectional fiber glass customized post and core system instead of a conventional fiber post. The fabrication of this glass fiber customized post is a simple technique, providing an increased volume of fibers into the root canal, and an adequate polymerization of the post-core system. Over a three-year period, the treatments demonstrated good clinical and radiographic characteristics, with no fracture or loss of the post and/or crown. This technique can be considered effective, less invasive, and suitable for restore endodontically treated teeth. (Eur J Dent 2011;5:107-112)

scholarly journals Fracture Resistance of Simulated Immature Teeth after Different Intra-radicular Treatments

2015 ◽  
Vol 26 (3) ◽  
pp. 211-215 ◽  
Author(s):  
Gustavo Sivieri-Araujo ◽  
Mario Tanomaru-Filho ◽  
Juliane Maria Guerreiro-Tanomaru ◽  
Eduardo Antunes Bortoluzzi ◽  
Érica Gouveia Jorge ◽  
...  
Keyword(s):  
Glass Fiber ◽  
Fracture Strength ◽  
Root Canal ◽  
Fracture Resistance ◽  
Testing Machine ◽  
Fiber Post ◽  
Immature Teeth ◽  
Fiber Posts ◽  
Glass Fiber Posts ◽  
Glass Fiber Post

The aim of this study was to evaluate the fracture resistance of simulated immature teeth after different intra-radicular treatments. Crowns and roots of bovine incisors were cut transversally and removed to simulate immature teeth. Root canal preparation and flaring were performed using a bur in crown-apex and apex-crown direction. The samples were distributed into 5 groups (n=10): Positive control (PoC) - no root canal flaring or filling; Negative control (NeC) - teeth were sectioned and their root canals were flared; Direct anatomical glass fiber post (RaP) - #2 Reforpost main glass fiber post relined with composite resin; Double tapered conical glass fiber posts (ExP) - #3 Exacto glass fiber post; and #2 Reforpost main glass fiber + Reforpin accessory glass fiber posts (RrP). In RaP, ExP and RrP, 4.0-mm apical plugs were done with MTA Angelus. The specimens were embedded in polystyrene resin inside cylinders and the periodontal ligament was simulated with a polyether-based impression material. The specimens were submitted to compressive fracture strength test (0.5 mm/min at 135° relative to the long axis of the tooth) in a servo-hydraulic mechanical testing machine MTS 810. Data were subjected to one-way ANOVA and Dunnett's C or Tukey's tests (α=0.05). The control groups (PoC and NeC) showed lower fracture strength than the experimental groups. NeC presented the lowest resistance and ExP presented the highest resistance among the experimental groups. The flaring procedures produced a detrimental effect on the fracture resistance of the bovine teeth. Glass fiber intra-radicular posts increased significantly the fracture resistance of simulated immature teeth.

Fracture Resistance and Failure Patterns of Endodontically Treated Mandibular Molars Restored Using Resin Composite With or Without Translucent Glass Fiber Posts

2006 ◽  
Vol 32 (8) ◽  
pp. 752-755 ◽  
Author(s):  
Ziad Salameh ◽  
Roberto Sorrentino ◽  
Federica Papacchini ◽  
Hani F. Ounsi ◽  
Esam Tashkandi ◽  
...  
Keyword(s):  
Glass Fiber ◽  
Fracture Resistance ◽  
Resin Composite ◽  
Failure Patterns ◽  
Mandibular Molars ◽  
Fiber Posts ◽  
Glass Fiber Posts
Sign in / Sign up

Export Citation Format

Share Document