scholarly journals Leakage Characteristic Identification of Labyrinth Seals on Reciprocating Piston through Transient Simulations

2019 ◽  
Vol 2019 ◽  
pp. 1-12
Author(s):  
Lingzi Wang ◽  
Jianmei Feng ◽  
Mingfeng Wang ◽  
Zenghui Ma ◽  
Xueyuan Peng
Keyword(s):  
Flow Rate ◽  
Pressure Ratio ◽  
Piston Compressor ◽  
Pressure Change ◽  
Labyrinth Seal ◽  
Relative Molecular Mass ◽  
Geometrical Parameters ◽  
Leakage Flow ◽  
Reciprocating Motion ◽  
Leakage Flow Rate

In the reciprocating labyrinth piston compressor, the characteristic of the internal leakage is crucial for the leakage management and performance improvement of the compressor. However, most of the published studies investigated the rotor-stator system, and those who study the reciprocating piston-cylinder system basically focus on the effects of the geometrical parameters. These conclusions could not directly be applied to predict the real-time leakage flow rate through the labyrinth seal because of the fast reciprocating motion of the piston, which will cause continually pressure change in two compression chambers, and then the pressure fluctuation will affect the flow through the labyrinth seal. A transient simulation model employing the multiscale dynamic mesh, which considers the effect of the reciprocating motion of the piston in the cylinder, is established to identify the characteristics of the internal leakage. This model was verified by a specially designed compressor, and the influence of various parameters was analyzed in detail. The sealing performance decreased linearly with the increase in the pressure ratio, and higher pressure inlet leads to higher leakage flow under the same pressure ratio. The labyrinth seal performance positively correlated to the increase of the rotational speed. Leakage characteristics of five working mediums were carried out, and the results indicated that the relative leakage decreased with an increase in the relative molecular mass. From this study, the realistic internal leakage flow rate under different operating parameters in the reciprocating labyrinth piston compressor could be predicated.

Effects of Pressure Ratio and Fin Pitch on Leakage Flow Characteristics in High Rotating Labyrinth Seals

2006 ◽  
Author(s):  
Jun Li ◽  
Xin Yan ◽  
Zhenping Feng
Keyword(s):  
Flow Rate ◽  
Geometrical Structure ◽  
Pressure Ratio ◽  
Flow Characteristics ◽  
Labyrinth Seal ◽  
Leakage Flow ◽  
Rotational Axis ◽  
Labyrinth Seals ◽  
Sealing Performance ◽  
Leakage Flow Rate

Labyrinth seals represent an important flow element in the sealing equipment of modern turbomachinery industries. The straight-through and stepped labyrinth seal are widely used in modern steam turbine due to their comparable simple structure and low manufactured costs. The influence of pressure ratio and fin pitch on the leakage flow characteristics of the straight-through and stepped labyrinth seals is numerically determined. The pressure ratio is defined as the outlet static pressure divided by the inlet total pressure. The fin pitch varied in the fixed axial distance of the labyrinth seal. The geometries investigated represent designs of the straight-through and stepped labyrinth seal typical for modern steam turbines. The leakage flow fields in the high rotating straight-through and stepped labyrinth seals are obtained by the Reynolds-Averaged Navier-Stokes solution using the commercial software FLUENT with the fixed seal clearance and fins geometrical structure. The effect of the rotational axis is also taken into account in numerical computations. Numerical simulations covered a range of pressure ratio and fin pitch for the straight-through and stepped labyrinth seals. Dimensionless discharge coefficients, describing the sealing performance, are calculated from the simulation results. The numerical results show that pressure ratio and fin pitch both affects the sealing performance with the fixed seal clearance and fin geometrical structure. The leakage flow rate decreases with the decreasing fin pitch for both the straight-through and stepped labyrinth seal at the fixed pressure ratio. Furthermore, the leakage flow rate decreases with the increasing pressure ratio at the fixed fin pitch for two kinds of labyrinth seals in the present study. This research provides technical support for improved design of labyrinth seals in turbomachinery.

Numerical Investigations on the Leakage Flow Characteristics of Pocket Damper Seals

2011 ◽  
Author(s):  
Zhigang Li ◽  
Jun Li ◽  
Zhenping Feng ◽  
Jiandao Yang ◽  
Rui Yang ◽  
...  
Keyword(s):  
Flow Rate ◽  
Rotational Speed ◽  
Pressure Ratio ◽  
Flow Characteristics ◽  
Labyrinth Seal ◽  
Leakage Rate ◽  
Numerical Results ◽  
Flow Coefficient ◽  
Leakage Flow ◽  
Leakage Flow Rate

The effects of pressure ratios, rotational speeds and sealing clearances on the leakage flow characteristics of pocket damper seals (PDS) were numerically investigated using Reynolds-Averaged Navier-Stokes (RANS) solutions. The leakage flow rate of the experimental PDS with the eight-bladed and eight-pocket was conducted at three different pressure drops and three different rotational speeds. The numerical results were in agreement with the experimental data. Six pressure ratios, four rotational speeds and four sealing clearances were utilized to study the effects of theses factors on the leakage flow characteristics of the PDS. Numerical results show that the leakage rate of the PDS increases with decreased pressure ratio. The leakage rate decreases with the increasing rotational speed, and this phenomenon is more pronounced at higher rotational speed. At the highest rotational speed 20200rpm, the flow coefficient is up to 4.4% less than that of the non-rotating case. The leakage rate increases linearly with sealing clearance increasing. The comparison of the leakage flow rate shows that the PDS leaks slightly less than that of the labyrinth seal at the same pressure ratio, rotational speed and sealing clearance, especially at the higher rotational speed case. Furthermore, the circumferential partition wall can significantly decrease the circumferential flow in the PDS cavity. At the highest rotational speed with 20200rpm, the swirl ratio in the active and inactive cavity of the PDS is reduced by 94.5% and 46% compared to the labyrinth seal, respectively.

Numerical Investigations on the Leakage and Rotordynamic Characteristics of Pocket Damper Seals—Part II: Effects of Partition Wall Type, Partition Wall Number, and Cavity Depth

2014 ◽  
Vol 137 (3) ◽  
Author(s):  
Zhigang Li ◽  
Jun Li ◽  
Zhenping Feng
Keyword(s):  
Flow Rate ◽  
Labyrinth Seal ◽  
Leakage Flow ◽  
Cavity Depth ◽  
Partition Wall ◽  
Leakage Flow Rate ◽  
Direct Stiffness ◽  
Cfd Method ◽  
Positive Direct ◽  
Orbit Model

Effects of partition wall type, partition wall number and cavity depth on the leakage and rotordynamic characteristics of the pocket damper seal (PDS) were numerically investigated using a presented 3D transient computational fluid dynamics (CFD) method based on the multifrequency elliptical whirling orbit model. The accuracy and availability of this transient CFD method and the multifrequency elliptical whirling orbit model were demonstrated with the experimental data of the experimental eight-bladed fully partitioned pocket damper seal (FPDS). The leakage flow rates and frequency-dependent rotordynamic coefficients of PDS were computed for two types of partition wall (namely conventional PDS and fully partitioned PDS), four partition wall numbers including the labyrinth seal (no partition wall) and six cavity depths including the plain smooth seal (zero cavity depth) at operational conditions with or without inlet preswirl and 15,000 rpm rotational speed. The numerical results show that the FPDS has the similar leakage performance and more superior stability capacity than the conventional PDS. The FPDS possesses slightly larger leakage flow rate (∼2.6–4.0% larger) compared to the labyrinth seal. Eight is a preferable value for the partition wall number to gain the best leakage performance of the FPDS with the least manufacturing cost. The FPDS possesses significantly larger stiffness and damping than the labyrinth seal. Increasing partition wall number results in a significant increase in the direct stiffness but limited desirable effect on the effective damping. The FPDS possesses the lowest leakage flow rate when the cavity depth is about 2.0 mm. Compared to the plain smooth seal, the FPDS possesses larger positive direct stiffness and significantly less direct damping and effective damping. Increasing cavity depth results in a significant decrease in the stabilizing direct damping and the magnitude of the destabilizing cross-coupling stiffness. H= 3.175 mm is a preferable value of the cavity depth for which the effective damping of the FPDS is largest, especially for the concerned frequencies (80–120 Hz) where most multistage high-pressure centrifugal compressors have stability problem.

scholarly journals Optimizing the Geometric Parameters of a Straight-Through Labyrinth Seal to Minimize the Leakage Flow Rate and the Discharge Coefficient

Energies ◽  
2021 ◽  
Vol 14 (3) ◽  
pp. 705
Author(s):  
Seung Il Baek ◽  
Joon Ahn
Keyword(s):  
Flow Rate ◽  
Axial Length ◽  
Discharge Coefficient ◽  
Labyrinth Seal ◽  
Geometric Parameters ◽  
Navier Stokes ◽  
Leakage Flow ◽  
Leakage Flow Rate ◽  
Tooth Width ◽  
Cavity Width

A straight-through labyrinth seal is one of the most popular non-contacting annular seals through which energy dissipation by turbulence viscosity interaction is achieved with a series of teeth and cavities. The geometric parameters of the straight-through labyrinth seal, such as clearance, tooth width, tooth height, cavity width, and tooth inclination angle, affect its performance. The space for installing a labyrinth seal in turbomachinery is limited, and so it is important to optimize its geometry for a fixed axial length in order to minimize the leakage flow rate and the discharge coefficient. The objective of the current study is to understand the effects of changing the geometric parameters of the seal on the leakage flow rate and the discharge coefficient, and to determine the optimized geometry for a fixed axial length. When the whole axial length is fixed, the most effective way to decrease the discharge coefficient is to reduce the cavity width by increasing the number of cavities. However, if the number of cavities is too high, the beneficial effect of more cavities can be reversed. The results of this study will help turbomachinery manufacturers to design a more efficient labyrinth seal. Numerical simulations of leakage flow for the straight-through labyrinth seal were carried out using Reynolds-Averaged Navier–Stokes (RANS) models, and the results for their discharge coefficients and pressure distributions were compared to previously published experimental data.

Effects of Pressure Ratio and Sealing Clearance on Leakage Flow Characteristics in the Rotating Honeycomb Labyrinth Seal

2007 ◽  
Author(s):  
Jun Li ◽  
Xin Yan ◽  
Guojun Li ◽  
Zhenping Feng
Keyword(s):  
Pressure Ratio ◽  
Flow Characteristics ◽  
Labyrinth Seal ◽  
Navier Stokes ◽  
Leakage Flow ◽  
Labyrinth Seals ◽  
Aerodynamic Efficiency ◽  
Flow Losses ◽  
Leakage Flow Rate ◽  
Swirl Velocity

Honeycomb stepped labyrinth seals in turbomachinery enhance aerodynamic efficiency by reducing leakage flow losses through the clearance between rotating and stationary components. The influence of pressure ratio and sealing clearance on the leakage flow characteristics in the honeycomb stepped labyrinth seal is numerically determined. The geometries investigated represent designs of the honeycomb labyrinth seal typical for modern turbomachinery. The leakage flow fields in the honeycomb and smooth stepped labyrinth seals are obtained by the Reynolds-Averaged Navier-Stokes solution using the commercial software FLUENT. Numerical simulations covered a range of pressure ratio and three sizes of sealing clearance for the honeycomb and smooth stepped labyrinth seals. The numerical discharge coefficients of the non-rotating honeycomb and smooth stepped labyrinth seals are in good agreement with previous experimental data. In addition rotational effects are also taken into account in numerical computations. The numerical results show that the leakage flow rate increases with the increasing pressure ratio at the fixed sealing clearance for the rotating and non-rotating honeycomb labyrinth seal. The influence of the sealing clearance on the leakage flow pattern for the rotating and non-rotating honeycomb labyrinth seal are observed. Moreover, the similar leakage flow rates are obtained at the same flow condition between the rotating and non-rotating honeycomb labyrinth seal due to the honeycomb acts to kill swirl velocity development for the rotating honeycomb labyrinth seal.

Performance Analysis of a Rotating Labyrinth Seal With Radial Growth

2013 ◽  
Author(s):  
Sivakumar Subramanian ◽  
A. S. Sekhar ◽  
B. V. S. S. S. Prasad
Keyword(s):  
Flow Rate ◽  
Radial Growth ◽  
Labyrinth Seal ◽  
Leakage Flow ◽  
Leakage Flow Rate ◽  
Wide Range ◽  
Structural Deformations ◽  
Angular Velocities ◽  
Computational Methodology ◽  
Initial Clearance

A computational methodology is proposed to predict the running clearance of a six-tooth straight-through rotating labyrinth seal numerically by taking into account both the centrifugal and thermal growths. Four different angular velocities ranging from 0 to 3000 rad/s are chosen to study the influence of rotation on the leakage flow rate. The detailed leakage flow fields and the structural deformations are presented. Further, different pressure ratios in the range of 1.1 to 2.5 have been investigated for a wide range of initial clearances. The methodology is validated against the available data in the literature. It is found out that there is a significant reduction in leakage flow rate by incorporating the radial growth for a particular operating condition. However, for a given initial clearance, the rotation has negligible effect on the reduction in the leakage flow rate, except at pressure ratios lower than 1.7. Further; the rotation has more prominent effect for smaller clearance values.

Numerical Investigations on the Leakage and Rotordynamic Characteristics of Pocket Damper Seals: Part II — Effects of Partition Wall Type, Partition Wall Number and Cavity Depth

2014 ◽  
Author(s):  
Zhigang Li ◽  
Jun Li ◽  
Zhenping Feng
Keyword(s):  
Flow Rate ◽  
Labyrinth Seal ◽  
Leakage Flow ◽  
Cavity Depth ◽  
Partition Wall ◽  
Leakage Flow Rate ◽  
Direct Stiffness ◽  
Cfd Method ◽  
Positive Direct ◽  
Orbit Model

Effects of partition wall type, partition wall number and cavity depth on the leakage and rotordynamic characteristics of the pocket damper seal (PDS) were numerically investigated using a presented 3D transient CFD method based on the multi-frequency elliptical whirling orbit model. The accuracy and availability of this transient CFD method and the multi-frequency elliptical whirling orbit model were demonstrated with the experimental data of the experimental eight-bladed fully-partitioned pocket damper seal (FPDS). The leakage flow rates and frequency-dependent rotordynamic coefficients of PDS were computed for two types of partition wall (namely conventional PDS and fully-partitioned PDS), four partition wall numbers including the labyrinth seal (no partition wall) and six cavity depths including the plain smooth seal (zero cavity depth) at operational conditions with or without inlet preswirl and 15000rpm rotational speed. The numerical results show that the FPDS has the similar leakage performance and more superior stability capacity than the conventional PDS. The FPDS possesses slightly larger leakage flow rate (∼2.6–4.0% larger) compared to the labyrinth seal. Eight is a preferable value for the partition wall number to gain the best leakage performance of the FPDS with the least manufacturing cost. The FPDS possesses significantly larger stiffness and damping than the labyrinth seal. Increasing partition wall number results in a significant increase in the direct stiffness but limited desirable effect on the effective damping. The FPDS possesses the lowest leakage flow rate when the cavity depth is about 2.0mm. Compared to the plain smooth seal, the FPDS possesses larger positive direct stiffness and significantly less direct damping and effective damping. Increasing cavity depth results in a significant decrease in the stabilizing direct damping and the magnitude of the destabilizing cross-coupling stiffness. H = 3.175mm is a preferable value of the cavity depth for which the effective damping of the FPDS is largest, especially for the concerned frequencies (80–120Hz) where most multistage high-pressure centrifugal compressors have stability problem.

On the choice of initial clearance and prediction of leakage flow rate for a rotating gas turbine seal

2015 ◽  
Vol 230 (10) ◽  
pp. 1586-1601 ◽  
Author(s):  
Sivakumar Subramanian ◽  
AS Sekhar ◽  
BVSSS Prasad
Keyword(s):  
Gas Turbine ◽  
Flow Rate ◽  
Pressure Ratio ◽  
Design Procedure ◽  
Leakage Flow ◽  
Clearance Ratio ◽  
Growth Ratio ◽  
Thermal Growth ◽  
Leakage Flow Rate ◽  
Initial Clearance

The present work proposes a design procedure along with guidelines for the choice of initial clearance of a typical rotating gas turbine seal in a secondary air system. The basis for the design is to prevent seal rubbing against stator, by ensuring that the centrifugal and thermal growths of the seal are within the safe operating limits. As a case study, a six-tooth straight-through rotating labyrinth seal configuration is considered with wide ranging seal parameters, namely the seal inner radius (25–700 mm), speed (1000–5000 rad/s), temperature (200–650 ℃) and pressure ratio (1.1–2.5). By means of an iterative process, which involves computational fluid dynamics and finite element analysis techniques, and with a choice of initial clearance, an extensive database is generated. The results are presented in terms of non-dimensional variables, namely seal clearance ratio, centrifugal growth ratio, thermal growth ratio, operating clearance ratio due to centrifugal growth and operating clearance ratio due to thermal growth. It is found that the value of clearance ratio depends significantly on the dimensionless radial position. For a seal clearance ratio of 0.01, at 3000 rad/s, the leakage flow rate gets reduced by 18 and 4%, respectively for pressure ratios of 1.1 and 2.5, when the centrifugal growth alone is considered. When both centrifugal and thermal growths are considered, the percentage reduction becomes about 70% for the same seal operating at 3000 rad/s and 204 ℃, and it is as high as 95% at 426 ℃.

Numerical Investigations on the Leakage Flow Characteristics of Brush Seal Based on the 3D Staggered Tube Bundle Model

2020 ◽  
Author(s):  
Dengqian Ma ◽  
Yuanqiao Zhang ◽  
Zhigang Li ◽  
Jun Li ◽  
Xin Yan
Keyword(s):  
Flow Rate ◽  
Tube Bundle ◽  
Pressure Ratio ◽  
Aerodynamic Resistance ◽  
Flow Characteristics ◽  
Leakage Flow ◽  
Rate Reduction ◽  
Brush Seal ◽  
Leakage Flow Rate ◽  
Rotational Components

Abstract Brush seals are widely applied in turbomachinery to control leakage flow between the stationary and rotational components due to the high sealing performance. In consideration of the axial compression of the bristle pack posing a challenge to accurately predict the leakage flow rate at the practical operating condition, the 3D staggered tube bundle model is established based on the multi-block structured mesh. The mesh motion technique is used to obtain the leakage flow pattern and aerodynamic resistance performance of the brush seal. The effects of pressure ratio Rp, sealing clearance c and axial pitch reduction ΔSx,i on leakage flow characteristics as well as Eu of the brush seal were investigated. The numerical results were in good agreement with the experimental data. Thus the accuracy of the presented numerical method was validated. For the contacting brush seal, ΔSx,i has a significant effect on the leakage flow rate reduction. As the ΔSx,i increases from 0 mm to 0.004 mm, the leakage flow rate is reduced by 39.63% when Rp equals to 1.5. For the clearance brush seal, ΔSx,i has little effect on the leakage flow rate reduction. As the ΔSx,i increases from 0 mm to 0.004 mm, the leakage flow rate is reduced by 3.44% when Rp equals to 1.5 and c equals to 0.2 mm. As for the aerodynamic resistance, the presence of the sealing clearance could effectively convert the pressure energy of the leakage flow into kinetic energy. This causes that the leakage flow velocity exiting the bristle pack of the clearance brush seal is 1.5 to 2.0 times than that of the contacting brush seal. Although the existence of the sealing clearance obviously increases the leakage flow rate, it effectively reduces the aerodynamic forces acting on the bristles. This research would provide technical support for the analysis of the leakage flow characteristics of the brush seal.

Sign in / Sign up

Export Citation Format

Share Document