scholarly journals Predicting Fatigue Life for Finite Line Contact under Starved Elastohydrodynamic Lubrication Condition

2020 ◽  
Vol 2020 ◽  
pp. 1-14
Author(s):  
Mingyong Liu ◽  
Haofeng Ku ◽  
Jinxi Zhang ◽  
Peidong Xu ◽  
Chenhui Wu
Keyword(s):  
Fatigue Life ◽  
Contact Fatigue ◽  
Elastohydrodynamic Lubrication ◽  
Operating Conditions ◽  
Line Contact ◽  
Finite Line Contact ◽  
Lubrication Performance ◽  
Finite Line ◽  
Lubrication Condition ◽  
Lubrication Characteristics

Surface contact fatigue is the main failure mode in many mechanical components, such as gears, bearings, and cam-followers. A fatigue life prediction model is proposed for finite line contact under starved thermal elastohydrodynamic lubrication (TEHL) condition in this paper. Then, the effects of inlet oil-supply thickness, slide-to-roll ratio (SRR), and operating conditions on the lubrication performance and fatigue life are investigated. The results show that the lubrication characteristics and fatigue life of finite line contact are obviously different from those of fully flooded situation by introducing the starved lubrication condition. For example, the severe starved conditions lead to a significant increase in friction coefficient and decreased fatigue life. The variation of SRR has an important influence on the fatigue life. With the increase of SRR, the fatigue life decreases firstly and then increases. The stress concentration occurs near the surface when speed is low. In addition, under the low-speed situation, rotation speed variation has little effect on the fatigue life.

scholarly journals A full numerical solution to the coupled cam–roller and roller–pin contact in heavily loaded cam–roller follower mechanisms

2017 ◽  
Vol 232 (10) ◽  
pp. 1273-1284 ◽  
Author(s):  
Shivam S Alakhramsing ◽  
Matthijn B de Rooij ◽  
Dirk J Schipper ◽  
Mark van Drogen
Keyword(s):  
Elastohydrodynamic Lubrication ◽  
Friction Model ◽  
Line Contact ◽  
Transient Effects ◽  
Power Losses ◽  
Lubricated Contacts ◽  
Finite Line Contact ◽  
Finite Line ◽  
Lubrication Characteristics ◽  
Lubrication Conditions

In cam–roller follower units two lubricated contacts may be distinguished, namely the cam–roller contact and roller–pin contact. The former is a nonconformal contact while the latter is conformal contact. In an earlier work a detailed transient finite line contact elastohydrodynamic lubrication model for the cam–roller contact was developed. In this work a detailed transient elastohydrodynamic lubrication model for the roller–pin contact is developed and coupled to the earlier developed cam–roller contact elastohydrodynamic lubrication model via a roller friction model. For the transient analysis a heavily loaded cam–roller follower unit is analyzed. It is shown that likewise the cam–roller contact, the roller–pin contact also inhibits typical finite line contact elastohydrodynamic lubrication characteristics at high loads. The importance of including elastic deformation for analyzing lubrication conditions in the roller–pin contact is highlighted here, as it significantly enhances the film thickness and friction coefficient. Other main findings are that for heavily loaded cam–roller follower units, as studied in this work, transient effects and roller slippage are negligible, and the roller–pin contact is associated with the highest power losses. Finally, due to the nontypical elastohydrodynamic lubrication characteristics of both cam–roller and roller–pin contact numerical analysis becomes inevitable for the evaluation of the film thicknesses, power losses, and maximum pressures.

A thermal EHL investigation on plate-pin hinge pairs in silent chains using a narrow finite line contact

2020 ◽  
Vol 72 (10) ◽  
pp. 1139-1145
Author(s):  
Mingyu Zhang ◽  
Jing Wang ◽  
Jinlei Cui ◽  
Peiran Yang
Keyword(s):  
Film Thickness ◽  
Temperature Rise ◽  
Elastohydrodynamic Lubrication ◽  
Radius Of Curvature ◽  
Line Contact ◽  
Equivalent Radius ◽  
Content Type ◽  
Finite Line Contact ◽  
Pressure Peak ◽  
Finite Line

Purpose The purpose of this paper is to numerically study the variations of oil film pressure, thickness and temperature rise in the contact zone of plate-pin pair in silent chains. Design/methodology/approach A steady-state thermal elastohydrodynamic lubrication (EHL) model is built using a Ree–Eyring fluid. The contact between the plate and the pin is simplified as a narrow finite line contact, and the lubrication state is examined by varying the geometry and the plate speed. Findings With increase in the equivalent radius of curvature, the pressure peak and the central film thickness increase. Because the plate is very thin, the temperature rise can be neglected. Even when the influence of the rounded corner region is less, a proper design can beneficially increase the minimum film thickness at both edges of the plate. Under a low entraining speed, strong stress concentration results in close-zero film thickness at both edges of the plate. Originality/value This study reveals the EHL feature of the narrow finite line contact in plate-pin pairs for silent chains and will support the future works considering transient effect, surface features and wear.

Mixed Elastohydrodynamic Lubrication With Three-Dimensional Machined Roughness in Spiral Bevel and Hypoid Gears

2015 ◽  
Vol 137 (4) ◽  
Author(s):  
Wei Pu ◽  
Jiaxu Wang ◽  
Rongsong Yang ◽  
Dong Zhu
Keyword(s):  
Three Dimensional ◽  
Elastohydrodynamic Lubrication ◽  
Operating Conditions ◽  
Strength Prediction ◽  
Flash Temperature ◽  
Hypoid Gears ◽  
Lubrication Performance ◽  
Lubrication Condition ◽  
Spiral Bevel ◽  
Film Lubrication

Spiral bevel and hypoid gears are key components widely used for transmitting significant power in various types of vehicles and engineering machineries. In reality, these gear surfaces are quite rough with three-dimensional (3D) topography that may significantly influence the lubrication formation and breakdown as well as components failures. Previous spiral bevel and hypoid gears lubrication studies, however, were limited mostly to cases under the full-film lubrication condition with smooth surfaces. In the present study, a comprehensive analysis for gearing geometry, kinematics, mixed lubrication performance, and friction and interfacial flash temperature in spiral bevel and hypoid gears is developed based on a recently developed mixed elastohydrodynamic lubrication (EHL) model that is capable of handling practical cases with 3D machined roughness under severe operating conditions and considering the effect of arbitrary entrainment angle. Obtained results from sample cases show that the simulation model developed can be used as an engineering tool for spiral bevel and hypoid gears design optimization and strength prediction.

Experimental Investigation for Finite Line Contact Edge Effect of Elastohydrodynamic Lubrication

2012 ◽  
Vol 538-541 ◽  
pp. 1945-1951 ◽  
Author(s):  
Yu Xue ◽  
Tong Shu Hua ◽  
Hao Yang Sun
Keyword(s):  
Experimental Investigation ◽  
Film Thickness ◽  
Contact Area ◽  
Elastohydrodynamic Lubrication ◽  
Line Contact ◽  
Heavy Load ◽  
Entrainment Velocity ◽  
Finite Line Contact ◽  
Finite Line ◽  
Lubricant Viscosity

To reveal the principle of the close effect about the EHL finite roller, contraposing the log-convex roller, the finite line contact EHL film shape and thickness were observed through self-made heavy-load optical EHL experimental device. Experiments were carried out under several different pressure and viscosity, and three groups of interference pictures were obtained under three different entrainment velocities. As the load increased, both the length and width of the roller contact area added, and the width of the contact zone in the end was larger than that in the centre, the close effect was more obvious; when the entrainment velocity and lubricant viscosity increased, the film thickness in the central roller became thicker while the increase in the roller end was little, the high film thickness difference enhanced the close effect. The entrainment velocity, load and lubricant viscosity all have great effect on the EHL characteristics of the finite roller.

Elastohydrodynamic Lubrication Analysis of Finite Line Contact Problem With Consideration of Two Free End Surfaces

2016 ◽  
Vol 139 (3) ◽  
Author(s):  
Haibo Zhang ◽  
Wenzhong Wang ◽  
Shengguang Zhang ◽  
Ziqiang Zhao
Keyword(s):  
Contact Problem ◽  
Finite Length ◽  
Elastohydrodynamic Lubrication ◽  
Line Contact ◽  
Free Boundaries ◽  
Finite Line Contact ◽  
Line Contacts ◽  
Speed Up ◽  
Finite Line ◽  
Overlapping Method

Elastohydrodynamic lubrication (EHL) analysis in finite line contacts is usually modeled by a finite-length roller contacting with a half-space, which ignores effect of the two free boundaries existing in many applications such as gears or roller bearings. This paper presents a semi-analytical method, involving the overlapping method and matrix formation, for EHL analysis in the finite line contact problem to consider the effect of two free end surfaces. Three half-spaces with mirrored loads to be solved are overlapped to cancel out the stresses at expected surfaces, and three matrices can be obtained and reused for the same finite-length space. The isothermal Reynolds equation is solved to obtain the pressure distribution and the fast Fourier transform (FFT) is used to speed up the elastic deformation and stress related calculation. Different line contact situations, including straight rollers, tapered rollers, and Lundberg profile rollers, are discussed to explore the effect of free end surfaces.

Effects of Working Conditions on TEHL Performance of a Helical Gear Pair With Non-Newtonian Fluids

2014 ◽  
Vol 136 (2) ◽  
Author(s):  
Mingyong Liu ◽  
Caichao Zhu ◽  
Huaiju Liu ◽  
Huafeng Ding ◽  
Zhangdong Sun
Keyword(s):  
Working Conditions ◽  
Power Law ◽  
Elastohydrodynamic Lubrication ◽  
Helical Gear ◽  
Gear Pair ◽  
Power Law Fluid ◽  
Finite Line Contact ◽  
Lubrication Performance ◽  
Finite Line ◽  
Helical Gear Pair

A thermal elastohydrodynamic lubrication (TEHL) finite line contact model is developed for a helical gear pair lubricated with an Eyring fluid or a power-law fluid in order to investigate the effects of the working conditions. A lubrication analysis within a meshing period shows that the differences between the Eyring and Newtonian solutions mainly lie in the film temperature and the shear stress. For the power-law fluid, the power index n has a significant effect on the film thickness. The effects of load and speed on lubrication performance along the line of action are discussed.

Elastohydrodynamic lubrication of coated finite line contacts

2017 ◽  
Vol 232 (9) ◽  
pp. 1077-1092 ◽  
Author(s):  
Shivam S Alakhramsing ◽  
Matthijn B de Rooij ◽  
Dirk J Schipper ◽  
Mark van Drogen
Keyword(s):  
Mechanical Properties ◽  
Film Thickness ◽  
Surface Profile ◽  
Elastohydrodynamic Lubrication ◽  
Operating Conditions ◽  
Maximum Pressure ◽  
Lubrication Performance ◽  
Line Contacts ◽  
Finite Line ◽  
Axial Surface

In this work, a finite element-based model is presented that simulates elastohydrodynamic lubrication in coated finite line contacts. Using this model, the film thickness and pressure distributions, between a straight roller with rounded edges on a plate, were analyzed. The model was successfully validated against representative results reported in literature. Parameter studies were conducted to study the influence of varying operating conditions, axial surface profile parameters and coating mechanical properties on the overall elastohydrodynamic lubrication behavior of the contact. It was found that in contrast with typical elastohydrodynamic lubrication behavior, the maximum pressure and minimum film thickness, which are located at the rear of the contact, are largely influenced by variations in load. Results also reveal that axial surface profile parameters and coating mechanical properties may act as amplifiers to the effect of load on pressure and film thickness distribution and can thus, if smartly chosen, significantly enhance lubrication performance.

Sign in / Sign up

Export Citation Format

Share Document