scholarly journals Effects of Hydrostatic Pocket Shape on the Flow Pattern and Pressure Distribution

1995 ◽  
Vol 1 (3-4) ◽  
pp. 225-235 ◽  
Author(s):  
M. J. Braun ◽  
M. Dzodzo
Keyword(s):  
Numerical Simulation ◽  
Pressure Distribution ◽  
Flow Pattern ◽  
Stokes Equations ◽  
The Other ◽  
Navier Stokes ◽  
Navier Stokes Equations ◽  
Hydrostatic Bearing ◽  
Collocated Grid ◽  
Dimensionless Formulation

The flow in a hydrostatic pocket is numerically simulated using a dimensionless formulation of the 2-D Navier-Stokes equations written in primitive variables, for a body fitted coordinates system, and applied through a collocated grid. In essence, we continue the work of Braun et al. 1993a, 1993b] and extend it to the study of the effects of the pocket geometric format on the flow pattern and pressure distribution. The model includes the coupling between the pocket flow and a finite length feedline flow, on one hand, and the pocket and its adjacent lands on the other hand. In this context we shall present, on a comparative basis, the flow and the pressure patterns at the runner surface for square, ramped-Rayleigh step, and arc of circle pockets. Geometrically all pockets have the same footprint, same lands length, and same capillary feedline. The numerical simulation uses the Reynolds number based on the lid(runner) velocity and the inlet jet strengthFas the dynamic similarity parameters. The study aims at establishing criteria for the optimization of the pocket geometry in the larger context of the performance of a hydrostatic bearing.

Influences of Recess Geometry and Restrictor Dimension on Flow Patterns and Pressure Distribution of Hydrostatic Bearings

2007 ◽  
Author(s):  
Cheng-Hsien Chen ◽  
Yuan Kang ◽  
Yeon-Pun Chang ◽  
De-Xing Peng ◽  
Ding-Wen Yang
Keyword(s):  
Pressure Distribution ◽  
Stokes Equations ◽  
Flow Patterns ◽  
Lubricant Film ◽  
Navier Stokes ◽  
Width Ratio ◽  
Navier Stokes Equations ◽  
Hydrostatic Bearing ◽  
Lubricant Flow ◽  
Land Width

This paper studies the influences of recess geometry and restrictor dimensions on the flow patterns and pressure distribution of lubricant film, which are coupled effects of hybrid characteristics of a hydrostatic bearing. The lubricant flow is described by using the Navier-Stokes equations. The Galerkin weighted residual finite element method is applied to determine the lubricant velocities and pressure in the bearing clearance. The numerical simulations will evaluate the effects of the land-width ratio and restriction parameter as well as the influence of modified Reynolds number and the jet-strength coefficient on the flow patterns in the recess and pressure distribution in lubricant film. On the basis of the simulation drawn from this study, the simulated results are expected to help engineers make better use of the design of hydrostatic bearing and its restrictors.

On Direct Numerical Simulation of Turbulent Flows

2011 ◽  
Vol 64 (2) ◽  
Author(s):  
Giancarlo Alfonsi
Keyword(s):  
Numerical Simulation ◽  
Direct Numerical Simulation ◽  
High Performance Computing ◽  
Turbulent Flows ◽  
High Performance ◽  
Stokes Equations ◽  
Navier Stokes ◽  
Turbulent Shear ◽  
Navier Stokes Equations ◽  
Performance Computing

The direct numerical simulation of turbulence (DNS) has become a method of outmost importance for the investigation of turbulence physics, and its relevance is constantly growing due to the increasing popularity of high-performance-computing techniques. In the present work, the DNS approach is discussed mainly with regard to turbulent shear flows of incompressible fluids with constant properties. A body of literature is reviewed, dealing with the numerical integration of the Navier-Stokes equations, results obtained from the simulations, and appropriate use of the numerical databases for a better understanding of turbulence physics. Overall, it appears that high-performance computing is the only way to advance in turbulence research through the front of the direct numerical simulation.

scholarly journals Numerical stability analysis of a vortex ring with swirl

2019 ◽  
Vol 878 ◽  
pp. 5-36 ◽  
Author(s):  
Yuji Hattori ◽  
Francisco J. Blanco-Rodríguez ◽  
Stéphane Le Dizès
Keyword(s):  
Numerical Simulation ◽  
Growth Rate ◽  
Direct Numerical Simulation ◽  
Vortex Ring ◽  
Stokes Equations ◽  
Base Flow ◽  
Critical Layer ◽  
Navier Stokes ◽  
Instability Mode ◽  
Navier Stokes Equations

The linear instability of a vortex ring with swirl with Gaussian distributions of azimuthal vorticity and velocity in its core is studied by direct numerical simulation. The numerical study is carried out in two steps: first, an axisymmetric simulation of the Navier–Stokes equations is performed to obtain the quasi-steady state that forms a base flow; then, the equations are linearized around this base flow and integrated for a sufficiently long time to obtain the characteristics of the most unstable mode. It is shown that the vortex rings are subjected to curvature instability as predicted analytically by Blanco-Rodríguez & Le Dizès (J. Fluid Mech., vol. 814, 2017, pp. 397–415). Both the structure and the growth rate of the unstable modes obtained numerically are in good agreement with the analytical results. However, a small overestimation (e.g. 22 % for a curvature instability mode) by the theory of the numerical growth rate is found for some instability modes. This is most likely due to evaluation of the critical layer damping which is performed for the waves on axisymmetric line vortices in the analysis. The actual position of the critical layer is affected by deformation of the core due to the curvature effect; as a result, the damping rate changes since it is sensitive to the position of the critical layer. Competition between the curvature and elliptic instabilities is also investigated. Without swirl, only the elliptic instability is observed in agreement with previous numerical and experimental results. In the presence of swirl, sharp bands of both curvature and elliptic instabilities are obtained for $\unicode[STIX]{x1D700}=a/R=0.1$, where $a$ is the vortex core radius and $R$ the ring radius, while the elliptic instability dominates for $\unicode[STIX]{x1D700}=0.18$. New types of instability mode are also obtained: a special curvature mode composed of three waves is observed and spiral modes that do not seem to be related to any wave resonance. The curvature instability is also confirmed by direct numerical simulation of the full Navier–Stokes equations. Weakly nonlinear saturation and subsequent decay of the curvature instability are also observed.

scholarly journals Mixing of Particles in Micromixers under Different Angles and Velocities of the Incoming Water

Proceedings ◽  
2018 ◽  
Vol 2 (11) ◽  
pp. 577 ◽  
Author(s):  
Evangelos Karvelas ◽  
Christos Liosis ◽  
Theodoros Karakasidis ◽  
Ioannis Sarris
Keyword(s):  
Stokes Equations ◽  
Velocity Ratio ◽  
The Other ◽  
Navier Stokes ◽  
Contaminated Water ◽  
Solution Flow ◽  
Navier Stokes Equations ◽  
Inlet Velocity ◽  
Metal Capture ◽  
Discrete Motion

A possible solution for water purification from heavy metals is to capture them by using nanoparticles in microfluidic ducts. In this technique, heavy metal capture is achieved by effectively mixing two streams, a nanoparticle solution and the contaminated water. In the present work, particles and water mixing is numerically studied for various inlet velocity ratios and inflow angles of the two streams. The Navier-Stokes equations are solved for the water flow while the discrete motion of particles is evaluated by a Lagrangian method. Results showed that as the velocity ratio between the inlet streams increases, by increasing the particles solution flow, the mixing of particles with the contaminated water is increased. Thus, nanoparticles are more uniformly distributed in the duct. On the other hand, angle increase between the inflow streams ducts is found to be less significant.

scholarly journals Propagation of Solitary Waves over a Submerged Slotted Barrier

2020 ◽  
Vol 8 (6) ◽  
pp. 419 ◽  
Author(s):  
Yun-Ta Wu ◽  
Shih-Chun Hsiao
Keyword(s):  
Flow Pattern ◽  
Solitary Waves ◽  
Vortex Shedding ◽  
Stokes Equations ◽  
Navier Stokes ◽  
Model Data ◽  
Free Surface Elevation ◽  
Complex Flow ◽  
Laboratory Observation ◽  
Navier Stokes Equations

In this article, the interaction of solitary waves and a submerged slotted barrier is investigated in which the slotted barrier consists of three impermeable elements and its porosity can be determined by the distance between the two neighboring elements. A new experiment is conducted to measure free surface elevation, velocity, and turbulent kinetic energy. Numerical simulation is performed using a two-dimensional model based on the Reynolds-Averaged Navier-Stokes equations and the non-linear k-ɛ turbulence model. A detailed flow pattern is illustrated by a flow visualization technique. A laboratory observation indicates that flow separations occur at each element of the slotted barrier and the vortex shedding process is then triggered due to the complicated interaction of those induced vortices that further create a complex flow pattern. During the vortex shedding process, seeding particles that are initially accumulated near the seafloor are suspended by an upward jet formed by vortices interacting. Model-data comparisons are carried out to examine the accuracy of the model. Overall model-data comparisons are in satisfactory agreement, but modeled results sometimes fail to predict the positions of the induced vortices. Since the measured data is unique in terms of velocity and turbulence, the dataset can be used for further improvement of numerical modeling.

Sign in / Sign up

Export Citation Format

Share Document