scholarly journals Modeling of 120W Monocrystalline Photovoltaic Module using MATLAB Simulink

2018 ◽  
Vol 11 (1) ◽  
pp. 74
Author(s):  
Siti Amely Jumaat ◽  
Adhwa Amsyar Syazwan Ab Majid ◽  
Mohd Noor Abdullah ◽  
Nur Hanis Radzi ◽  
Rohaiza Hamdan ◽  
...  
Keyword(s):  
Renewable Energy ◽  
Solar Irradiance ◽  
Standard Test ◽  
Photovoltaic Module ◽  
Solar Photovoltaic ◽  
Matlab Simulink ◽  
Pv Module ◽  
Input Parameters ◽  
And Performance

This project aims to model a solar Photovoltaic (PV) Module using MATLAB Simulink. In Renewable Energy (RE) field, many studies have been carried out to determine the level of efficiency and performance of a specific PV module. Therefore, this research will carry out the modeling of the 120W Monocrystalline Photovoltaic Module by Su-Kam Solar using MATLAB Simulink to determine the efficiency and performance. The input parameters that consists of Solar Irradiance (G) and Temperature (T) data will be collected at location 1.8635° N, 103.1089° E which is in Parit Raja, Batu Pahat, Johor. The results are shown in I-V curve and P-V curve and compared with the theory of I-V and P-V curve. Other than that, the PV module have different performance in different value of irradiance and temperature. Lastly, the PV Module is work efficiently and full performance at Standard Test Conditon (STC).

Modelling and Simulation of Solar Photovoltaic Cell for Different Insolation Values Based on MATLAB/Simulink Environment

2014 ◽  
Vol 550 ◽  
pp. 137-143 ◽  
Author(s):  
S. Narendiran ◽  
Sarat Kumar Sahoo
Keyword(s):  
Photovoltaic Cell ◽  
Photovoltaic Module ◽  
Solar Photovoltaic ◽  
Electrical Characteristics ◽  
Array Type ◽  
Matlab Simulink ◽  
Photovoltaic Modules ◽  
Pv Module ◽  
Current Input ◽  
In Series

The paper discuss about the modelling and electrical characteristics of photovoltaic cell and its array type of construction in matlab-simulink environment at different insolation levels. The photovoltaic module is modelled using the diode electrical characteristic equation. The photovoltaic cell is analysed by voltage input and current input modules, The voltage and current input photovoltaic modules are simulated with different insolation values by varying the construction of PV modules. The results conclude that the current input PV module is well suited for applications were it shares same current when connected in series and voltage input PV module, where it shares same voltage when connected in parallel.

scholarly journals Modeling and Simulation of a PV Module Based Power System Using MATLAB/Simulink

2015 ◽  
Vol 62 (2) ◽  
pp. 127-132 ◽  
Author(s):  
Protap Kumar Mahanta ◽  
Khokan Debnath ◽  
Md Habibur Rahman
Keyword(s):  
Solar Irradiance ◽  
Maximum Power ◽  
Solar Pv ◽  
Pv System ◽  
Matlab Simulink ◽  
Pv Module ◽  
Power Stage ◽  
In Series ◽  
Natural Variable ◽  
And Performance

Due to the variation of solar irradiance, temperature and shading conditions, the power generated by a photovoltaic (PV) module and hence the power delivered to the load changes drastically, which imposes the need for analysis of a complete PV system to get the maximum power under these natural variable conditions. In this paper, a complete off-grid PV module based power generation system has been designed and simulated using MATLAB/Simulink and performance has been scrutinized using the value of standard solar irradiance about 1 KW/m-2 for Bangladesh. The simulation model includes solar PV module, the converter power stage with MPPT control and charge controlling functions and here performance of each block has been examined conspicuously. Eventually, it has been found that the model is quite competent to simulate both the I-V and P-V characteristics of a PV module and based on the result it has been predicted that the performance of several modules or even PV array connected in series and/or in parallel with the delivery of maximum power can be tested under different solar irradiance and temperature conditions. DOI: http://dx.doi.org/10.3329/dujs.v62i2.21977 Dhaka Univ. J. Sci. 62(2): 127-132, 2014 (July)

scholarly journals Analysis of Power Generation for Solar Photovoltaic Module with Various Internal Cell Spacing

2021 ◽  
Vol 13 (11) ◽  
pp. 6364
Author(s):  
June Raymond L. Mariano ◽  
Yun-Chuan Lin ◽  
Mingyu Liao ◽  
Herchang Ay
Keyword(s):  
Power Output ◽  
Spacing Effect ◽  
Photovoltaic Cell ◽  
Standard Test ◽  
Photovoltaic Module ◽  
Solar Pv ◽  
Engineering Software ◽  
Internal Cell ◽  
Cell Spacing ◽  
Pv Module

Photovoltaic (PV) systems directly convert solar energy into electricity and researchers are taking into consideration the design of photovoltaic cell interconnections to form a photovoltaic module that maximizes solar irradiance. The purpose of this study is to evaluate the cell spacing effect of light diffusion on output power. In this work, the light absorption of solar PV cells in a module with three different cell spacings was studied. An optical engineering software program was used to analyze the reflecting light on the backsheet of the solar PV module towards the solar cell with varied internal cell spacing of 2 mm, 5 mm, and 8 mm. Then, assessments were performed under standard test conditions to investigate the power output of the PV modules. The results of the study show that the module with an internal cell spacing of 8 mm generated more power than 5 mm and 2 mm. Conversely, internal cell spacing from 2 mm to 5 mm revealed a greater increase of power output on the solar PV module compared to 5 mm to 8 mm. Furthermore, based on the simulation and experiment, internal cell spacing variation showed that the power output of a solar PV module can increase its potential to produce more power from the diffuse reflectance of light.

scholarly journals Modeling of Photovoltaic Module Using the MATLAB

2019 ◽  
Vol 9 ◽  
pp. 59-69
Author(s):  
Alok Dhaundiyal ◽  
Divine Atsu
Keyword(s):  
Standard Test ◽  
Electrical Performance ◽  
Photovoltaic Module ◽  
Solar Pv ◽  
Pv Module ◽  
Proposed Model ◽  
Current Voltage ◽  
Pv Modules ◽  
The Impact ◽  
The Mathematical Model

This paper presents the modeling and simulation of the characteristics and electrical performance of photovoltaic (PV) solar modules. Genetic coding is applied to obtain the optimized values of parameters within the constraint limit using the software MATLAB. A single diode model is proposed, considering the series and shunt resistances, to study the impact of solar irradiance and temperature on the power-voltage (P-V) and current-voltage (I-V) characteristics and predict the output of solar PV modules. The validation of the model under the standard test conditions (STC) and different values of temperature and insolation is performed, as well as an evaluation using experimentally obtained data from outdoor operating PV modules. The obtained results are also subjected to comply with the manufacturer’s data to ensure that the proposed model does not violate the prescribed tolerance range. The range of variation in current and voltage lies in the domain of 8.21 – 8.5 A and 22 – 23 V, respectively; while the predicted solutions for current and voltage vary from 8.28 – 8.68 A and 23.79 – 24.44 V, respectively. The measured experimental power of the PV module estimated to be 148 – 152 W is predicted from the mathematical model and the obtained values of simulated solution are in the domain of 149 – 157 W. The proposed scheme was found to be very effective at determining the influence of input factors on the modules, which is difficult to determine through experimental means.

scholarly journals Modeling and Relative Research of Solar Photovoltaic Array Topologies Under Partial Shading Conditions

2019 ◽  
Vol 8 (11) ◽  
pp. 340-346
Keyword(s):  
Fill Factor ◽  
Electrical Power ◽  
Solar Photovoltaic ◽  
Power Losses ◽  
Partial Shading ◽  
Photovoltaic Array ◽  
Pv Array ◽  
Pv Module ◽  
And Performance ◽  
Zigzag Type

The electrical power generation from solar photo voltaic arrays increases by reducing partial shading effect due to the deposition of dust in modules, shadow of nearby buildings, cloud coverage leads to mismatching power losses. This paper gives the detailed analysis of modeling, simulation and performance analysis of different 4x4 size PV array topologies under different irradiance levels and to extract output power of panels maximum by reducing the mismatching power losses. For this analysis, a comparative study of six PV array topologies are Series, Parallel, Series-Parallel, Total-Cross-Tied, Bridge Linked and Honey-Comb are considered under various shading conditions such as one module shading, one string shading, zigzag type partial shading and total PV array partially shaded cases. The performance of above six topologies are compare with mismatching power losses and fill-factor. For designing and simulation of different PV array configurations/topologies in MaTLab/Simulink, the LG Electronics LG215P1W PV module parameters are used in all PV modules.

scholarly journals Design Modeling and Simulation of 150 KW Solar Photovoltaic Systems: A Review

2020 ◽  
Vol 9 (2) ◽  
pp. 703-706
Keyword(s):  
Carbon Dioxide ◽  
Renewable Energy ◽  
The Other ◽  
Photovoltaic System ◽  
Photovoltaic Module ◽  
Solar Photovoltaic ◽  
Current Voltage ◽  
Effects Of Temperature ◽  
Solar Photovoltaic System ◽  
Design And Manufacture

Sun is the source of energy. Renewable energy is a clean eco-system free of harmful gasses such as carbon dioxide, and all the other harmful gases which are produced from the fossil. Many technologies have been used to design and manufacture the photovoltaic module. In this paper we have reviewed the design of solar photovoltaic system of using MatLab/Simulink. Characteristics of I-V and P-V are parameter of great importance in solar photovoltaic system. The effects of temperature and irradiation at the output of solar system that is current, voltage and output power have also been reviewed and studied.

scholarly journals Performance Analysis of Conventional, Hybrid and Optimal PV Array Configurations of Partially Shaded Modules

2019 ◽  
Vol 9 (1) ◽  
pp. 3061-3073
Keyword(s):  
Performance Analysis ◽  
Solar Pv ◽  
Partial Shading ◽  
Power Number ◽  
Matlab Simulink ◽  
Pv Array ◽  
Pv Module ◽  
And Performance

In this paper, modeling and performance analysis of conventional configurations are Series-Parallel (SP), BridgeLinked (BL), Honey-Comb (HC), Total-Cross-Tied(TCT) and proposed hybrid configurations are SP-TCT, BL-TCT, HC-TCT, BL-HC and modified BL(MBL), modified HC(MHC), proposed optimal interconnection type configurations of a 5x5 size solar PV array under ten different partial shading cases it causes shading losses and compare the best configuration with respect to array power, number of interconnections or ties required between shaded modules in the array. The proposed optimal interconnection method reduces the number of ties required between modules and these ties are based on the position of number of shaded modules in the entire solar PV array. For the performance analysis of above 11 configurations, total ten shading cases are considered and compare the result with one un-shaded case-U of an irradiance 1000 W/m2 . The PV module parameters of Vikram Solar ELDORA 270 are used for modeling of above 11 conventional and proposed PV array configurations and simulate the models in MATLAB/ Simulink software.

scholarly journals Mathematical Modeling of Solar Photovoltaic Module to generate Maximum Power Using Matlab/Simulink

2021 ◽  
Vol 2 (1) ◽  
pp. 1-11
Author(s):  
Amusat Ramoni Olawale ◽  
Sulaimon Shodiya ◽  
Yakubu H Ngadda
Keyword(s):  
System Simulation ◽  
Real Life ◽  
Maximum Power ◽  
Photovoltaic Module ◽  
Solar Photovoltaic ◽  
Basic Tool ◽  
Pv Module ◽  
Accurate Design ◽  
Proposed Model ◽  
Module Type

Modeling is a basic tool of the real system simulation in translating the Mathematical results into real life. In this study, the Modeling and simulation of photovoltaic Module type PS-P310-36 were developed, and maximum power was obtained. The output I – V and P – V curves of the model were studied and analyzed under different irradiance (200 W/m2, 400 W/m, 600 W/m2, 800 W/m, and 1000 W/m2) at a constant temperature of 25oC. The model attained maximum power of 308, 251.6, 191.4, 129.2, and 64.74 W at 1000, 800, 600, 400, and 200 W/m2 irradiance, respectively. The model results agreed with the characteristics curves of the PV module of previous similar PV studies. The proposed model will serve as quick tools for designers in obtaining the maximum power of PV at distinct irradiance. However, for a more accurate design, more information is needed.

Sign in / Sign up

Export Citation Format

Share Document