Dye-Sensitized Solar Cells Based on Nanocrystalline Titania Electrodes Made at Various Sintering Temperatures

2007 ◽  
Vol 7 (2) ◽  
pp. 555-559 ◽  
Author(s):  
Elias Stathatos ◽  
Panagiotis Lianos
Keyword(s):  
Solar Cells ◽  
Short Circuit ◽  
Sol Gel ◽  
Dye Sensitized Solar Cells ◽  
Reaction Medium ◽  
Short Circuit Current ◽  
Open Circuit ◽  
Nanocrystalline Titania ◽  
Dye Sensitized ◽  
Sensitized Solar Cells

Dye-sensitized solar cells were made by using nanocrystalline titania deposited on Fluorine-doped SnO2 (FTO) electrodes. Nanocrystalline titania deposition was made by the sol–gel method using reverse micelles of bis(2-ethylhexyl) sulfosuccinate sodium salt (AOT) in cyclohexane as reaction medium. This surfactant could be easily removed from the deposited nanocomposite organic-inorganic film by simple rinsing with distilled water, without affecting titania adherence on FTO electrode. These nanocrystalline titania electrodes were used to make solar cells either without sintering or after sintering at various temperatures. Sintering extensively affected short circuit current but had small effect on device open-circuit voltage. Thus satisfactory photovoltaic response could be obtained even with devices made of non-sintered (room-temperature) titania.

scholarly journals Prunus domestica dye extraction for fabrication of zinc oxide based dye-sensitized solar cells

BIBECHANA ◽  
2015 ◽  
Vol 13 ◽  
pp. 23-28
Author(s):  
Leela Pradhan Joshi
Keyword(s):  
Zinc Oxide ◽  
Solar Cells ◽  
Short Circuit ◽  
Dye Sensitized Solar Cells ◽  
Short Circuit Current ◽  
Zinc Nitrate ◽  
Open Circuit ◽  
Dye Sensitized ◽  
Dye Extraction ◽  
Sensitized Solar Cells

Aluminium doped Zinc Oxide (AZO) seed layers were deposited on Fluorine doped Tin Oxide (FTO) substrates using a spin coating technique. These were then immersed in growth solutions of zinc nitrate, hexamethylenetetramine and distilled water to develop nanoplates of Zinc Oxide (ZnO). The nanostructures of ZnO grown on FTO were studied using x-ray diffraction techniques. Dye-sensitized solar cells (DSSC) were fabricated using two prepared electrodes, one of dye-loaded zinc oxide and another that was platinum coated. The electrolyte used was potassium iodide iodine solution. The performance of the assembled DSCCs was tested by drawing an IV curve. The results showed that the short circuit current and open circuit voltages were about 10 microamperes and 270 millivolts respectively.BIBECHANA 13 (2016) 23-28

scholarly journals There Is a Future for N-Heterocyclic Carbene Iron(II) Dyes in Dye-Sensitized Solar Cells: Improving Performance through Changes in the Electrolyte

Materials ◽  
2019 ◽  
Vol 12 (24) ◽  
pp. 4181 ◽  
Author(s):  
Mariia Karpacheva ◽  
Vanessa Wyss ◽  
Catherine E. Housecroft ◽  
Edwin C. Constable
Keyword(s):  
Solar Cells ◽  
Alkyl Chain ◽  
Electrochemical Impedance ◽  
Short Circuit ◽  
Dye Sensitized Solar Cells ◽  
Short Circuit Current ◽  
Open Circuit ◽  
Ion Concentration ◽  
Dye Sensitized ◽  
Sensitized Solar Cells

By systematic tuning of the components of the electrolyte, the performances of dye-sensitized solar cells (DSCs) with an N-heterocyclic carbene iron(II) dye have been significantly improved. The beneficial effects of an increased Li+ ion concentration in the electrolyte lead to photoconversion efficiencies (PCEs) up to 0.66% for fully masked cells (representing 11.8% relative to 100% set for N719) and an external quantum efficiency maximum (EQEmax) up to approximately 25% due to an increased short-circuit current density (JSC). A study of the effects of varying the length of the alkyl chain in 1-alkyl-3-methylimidazolium iodide ionic liquids (ILs) shows that a longer chain results in an increase in JSC with an overall efficiency up to 0.61% (10.9% relative to N719 set at 100%) on going from n-methyl to n-butyl chain, although an n-hexyl chain leads to no further gain in PCE. The results of electrochemical impedance spectroscopy (EIS) support the trends in JSC and open-circuit voltage (VOC) parameters. A change in the counterion from I− to [BF4]− for 1-propyl-3-methylimidazolium iodide ionic liquid leads to DSCs with a remarkably high JSC value for an N-heterocyclic carbene iron(II) dye of 4.90 mA cm−2, but a low VOC of 244 mV. Our investigations have shown that an increased concentration of Li+ in combination with an optimized alkyl chain length in the 1-alkyl-3-methylimidazolium iodide IL in the electrolyte leads to iron(II)-sensitized DSC performances comparable with those of containing some copper(I)-based dyes.

Fabrication of Core-Shell Structured TiO2/MgO Electrodes for Dye-Sensitized Solar Cells

2015 ◽  
Vol 787 ◽  
pp. 3-7 ◽  
Author(s):  
S. Karuppuchamy ◽  
C. Brundha
Keyword(s):  
Solar Cells ◽  
Short Circuit ◽  
Photovoltaic Performance ◽  
Dye Sensitized Solar Cells ◽  
Short Circuit Current ◽  
Open Circuit ◽  
Core Shell ◽  
Dye Sensitized ◽  
The Core ◽  
Sensitized Solar Cells

We demonstrated the construction and performance of dye-sensitized solar cells (DSCs) based on nanoparticles of TiO2coated with thin shells of MgO by simple solution growth technique. The XRD patterns confirm the presence of both TiO2and MgO in the core-shell structure. The effect of varied shell thickness on the photovoltaic performance of the core-shell structured electrode is also investigated. We found that MgO shells of all thicknesses perform as barriers that improve open-circuit voltage (Voc) of the DSCs only at the expense of a larger decrease in short-circuit current density (Jsc). The energy conversion efficiency was greatly dependent on the thickness of MgO on TiO2film, and the highest efficiency of 4.1% was achieved at the optimum MgO shell layer.

scholarly journals Model Dye-Sensitized Solar Cell dan Aplikasinya Berdasarkan Data Temperatur Harian: Studi Kasus Pangkalpinang

2021 ◽  
Vol 6 (2) ◽  
Author(s):  
Aliefia Noor ◽  
Meri Hamdini ◽  
Salsabila Ramadina ◽  
Yuant Tiandho
Keyword(s):  
Solar Cells ◽  
Short Circuit ◽  
Dye Sensitized Solar Cells ◽  
Short Circuit Current ◽  
Open Circuit ◽  
Effect Of Temperature ◽  
Synthesis Process ◽  
Dye Sensitized ◽  
Proposed Model ◽  
Sensitized Solar Cells

<p>Dye-Sensitized Solar Cells (DSSC) is photovoltaic with a dye that functions as an acceptor of sunlight. The great potential of using DSSC lies in the ease of the synthesis process, and the dyes used can come from plants. However, like most other solar cells, increasing the operating temperature can degrade the DSSC performance and thus decrease the efficiency. This article presents a model of the relationship between the effect of temperature on DSSC performance. The model proposed is derived from the DSSC equivalence with a diode circuit. By confirming the experimental research results, it is known that the model presented in this study has excellent accuracy on various DSSC performance parameters (R2&gt; 0.99). The performance studied includes the I-V curve's shape, the value of the short-circuit current, the diode leakage current, and the open-circuit voltage. Based on daily temperature data in Pangkalpinang City, the potential performance of the DSSC could also be determined when it was developed in Kep. Bangka Belitung. The short-circuit current value obtained is in the range of 14 A with a voltage of 0.6 V. It is hoped that this proposed model can be information for the development of DSSC because of its enormous potential application in Indonesia.</p>

Preparation and Photovoltaic Properties of Flexible Dye-Sensitized Solar Cells

2011 ◽  
Vol 306-307 ◽  
pp. 112-115 ◽  
Author(s):  
You Zeng ◽  
Li Jia Zhao ◽  
Ying Zhen ◽  
Fang Xiao Shi ◽  
Yu Tong
Keyword(s):  
Solar Cells ◽  
Short Circuit ◽  
Dye Sensitized Solar Cells ◽  
Short Circuit Current ◽  
Open Circuit ◽  
Treatment Temperature ◽  
Photovoltaic Properties ◽  
Dye Sensitized ◽  
Conductive Glass ◽  
Sensitized Solar Cells

Flexible dye-sensitized solar cells (DSCs) were prepared by using carbon nanotube transparent conductive films (CNT-TCFs) as flexible substrates, and their photovoltaic properties were investigated as well. The flexible DSCs show typical photovoltaic characteristics with short-circuit current of 0.78 μA and open-circuit voltage of 1.48 mV, which was strongly influenced by heat-treatment temperature, type of dyes, and electrical resistivity. In light of their lighter weight and higher flexibility than conventional DSCs based on conductive glass substrates, the flexible DSCs have great potential as functional photoelectric components in many fields.

Dye-Sensitized Solar Cells Based on Novel Mixed Dyes

2011 ◽  
Vol 383-390 ◽  
pp. 5510-5515
Author(s):  
Tien Tsan Hung
Keyword(s):  
Solar Cells ◽  
Electrochemical Impedance ◽  
Short Circuit ◽  
Sol Gel ◽  
Dye Sensitized Solar Cells ◽  
Open Circuit ◽  
Membrane Electrode ◽  
Dye Sensitized ◽  
Phthalocyanine Derivative ◽  
Sensitized Solar Cells

Novel phthalocyanine derivative and azo derivative have been synthesized as photosensitizers for the dye-sensitized solar cells (DSSCs). We used sol-gel method to prepare the titanium oxide (TiO2) membrane electrode of the DSSCs. The crystalline phase and surface morphology of TiO2 were characterized by using X-ray diffraction (XRD), and field emission scanning electron microscopy (FE-SEM) to investigate the effects of processing parameters on the films characteristic, microstructure and thickness. The performance of DSSCs was characterized by using electrochemical impedance spectroscopy (EIS) and current-voltage curve analysis. The sensitizing properties of phthalocyanine derivative, azo derivative and mixed dyes were studied, and it was found that the cell consisted of mixed dyes generated the highest power conversion efficiency () of 2.3 %, short circuit photocurrent density (Jsc) of 13.6 mA cm-2, open circuit photovoltage (Voc) of 0.46 V and fill factor (FF) of 0.37 under simulated AM 1.5 irradiation (100 mW cm-2) with a active area of 0.25 cm2.

The Preparation of ZnO Nanopowders and Dye Sensitized Solar Cells By Sol-Gel Method

2012 ◽  
Vol 512-515 ◽  
pp. 1533-1536
Author(s):  
Yan Xiang Wang ◽  
Sun Jian ◽  
Bing Xin Zhao
Keyword(s):  
Solar Cells ◽  
Zno Nanoparticles ◽  
Raw Materials ◽  
Short Circuit ◽  
Sol Gel ◽  
Dye Sensitized Solar Cells ◽  
Open Circuit ◽  
Molar Concentration ◽  
Dye Sensitized ◽  
Sensitized Solar Cells

In this paper, ZnO nanopowders and dye sensitized solar cells were prepared by sol-gel and screen printing method, respectively. First, ZnO nanopowders were synthesized by using zinc acetate, ethanol and diethanolamined as raw materials. The effects of Zn2+ molar concentration on the microstructure and photocatalytic efficiency of ZnO nanopowders were investigated. When Zn2+molar concentration were 0.4M, 0.6M, 0.8M and 1.2M, ZnO nanoparticles with diameter of about 80~100nm were obtained. When Zn2+ molar concentration reached 2.4M, ZnO nanobowls consisted of nanoparticles with diameter about 80~100nm were synthesized. When Zn2+molar concentration reached 3.6M, ZnO nanoparticles were obtained, and particle size distribution of obtained ZnO nanoparticles became broader. Methyl orange degradation rate of ZnO nanopowders prepared with 0.4M, after treated by ultraviolet radiation for 8 hours, were up to 88.5%. ZnO nanopowders prepared with 1.2M and 3.6M were assembled into solar cells. The properties of the solar cell prepared with 1.2M were optimal. The short-circuit photocurrent, open-circuit photovoltage, fill factor and efficiency were 14.72 mA/cm2, 0.649V, 0.332 and 0.914%, respectively.

scholarly journals Cobalt and Carbon Complex as Counter Electrodes in Dye-Sensitized Solar Cells

Photonics ◽  
2021 ◽  
Vol 8 (5) ◽  
pp. 166
Author(s):  
Chi-Feng Lin ◽  
Ting-Hsuan Hsieh ◽  
Yu-Chen Chou ◽  
Pin-Hung Chen ◽  
Ci-Wun Chen ◽  
...  
Keyword(s):  
Electrical Conductivity ◽  
Solar Cells ◽  
Short Circuit ◽  
Dye Sensitized Solar Cells ◽  
Short Circuit Current ◽  
Open Circuit ◽  
Counter Electrodes ◽  
Dye Sensitized ◽  
Thermal Sintering ◽  
Sensitized Solar Cells

We developed cobalt and carbon complex materials as counter electrodes (CEs) for dye-sensitized solar cells (DSSCs) to replace conventional platinum (Pt) CEs. Co12 and Co15, both of which are basic cobalt derivatives, showed good redox potential with a suitable open-circuit voltage (VOC); however, their poor electrical conductivity engendered a low short-circuit current (JSC) and fill factor (FF). Mixing them with carbon black (CB) improved the electrical conductivity of the CE; in particular, JSC and FF were considerably improved. Further improvement was achieved by combining cobalt derivatives and CB through thermal sintering to produce a novel CoCB material as a CE. CoCB had good electrical conductivity and electrocatalytic capability, and this further enhanced both JSC and VOC. The optimized device exhibited a power conversion efficiency (PCE) of 7.44%, which was higher than the value of 7.16% for a device with a conventional Pt CE. The conductivity of CoCB could be further increased by mixing it with PEDOT:PSS, a conducting polymer. The device’s JSC increased to 18.65 mA/cm2, which was considerably higher than the value of 14.24 mA/cm2 for the device with Pt CEs. The results demonstrate the potential of the cobalt and carbon complex as a CE for DSSCs.

scholarly journals Direct Growth of Flower-Shaped ZnO Nanostructures on FTO Substrate for Dye-Sensitized Solar Cells

Crystals ◽  
2019 ◽  
Vol 9 (8) ◽  
pp. 405 ◽  
Author(s):  
Ahmad Umar ◽  
Mohammad Akhtar ◽  
Tubia Almas ◽  
Ahmed Ibrahim ◽  
Mohammed Al-Assiri ◽  
...  
Keyword(s):  
Solar Cells ◽  
Short Circuit ◽  
Dye Sensitized Solar Cells ◽  
Solution Process ◽  
Morphological Characteristics ◽  
Short Circuit Current ◽  
Open Circuit ◽  
Zno Nanostructures ◽  
Dye Sensitized ◽  
Sensitized Solar Cells

The proposed work reports that ZnO nanoflowers were grown on fluorine-doped tin oxide (FTO) substrates via a solution process at low temperature. The high purity and well-crystalline behavior of ZnO nanoflowers were established by X-ray diffraction. The morphological characteristics of ZnO nanoflowers were clearly revealed that the grown flower structures were in high density with 3D floral structure comprising of small rods assembled as petals. Using UV absorption and Raman spectroscopy, the optical and structural properties of the ZnO nanoflowers were studied. The photoelectrochemical properties of the ZnO nanoflowers were studied by utilizing as a photoanode for the manufacture of dye-sensitized solar cells (DSSCs). The fabricated DSSC with ZnO nanoflowers photoanode attained reasonable overall conversion efficiency of ~1.40% and a short-circuit current density (JSC) of ~4.22 mA cm−2 with an open circuit voltage (VOC) of 0.615 V and a fill factor (FF) of ~0.54. ZnO nanostructures have given rise to possible utilization as an inexpensive and efficient photoanode materials for DSSCs.

scholarly journals Schiff Base Ancillary Ligands in Bis(diimine) Copper(I) Dye-Sensitized Solar Cells

2020 ◽  
Vol 21 (5) ◽  
pp. 1735
Author(s):  
Elias Lüthi ◽  
Paola Andrea Forero Cortés ◽  
Alessandro Prescimone ◽  
Edwin C. Constable ◽  
Catherine E. Housecroft
Keyword(s):  
Schiff Base ◽  
Solar Cells ◽  
Short Circuit ◽  
Dye Sensitized Solar Cells ◽  
Short Circuit Current ◽  
Open Circuit ◽  
Significant Loss ◽  
Aryl Group ◽  
Dye Sensitized ◽  
Sensitized Solar Cells

Five 6,6′-dimethyl-2,2′-bipyridine ligands bearing N-arylmethaniminyl substituents in the 4- and 4′-positions were prepared by Schiff base condensation in which the aryl group is Ph (1), 4-tolyl (2), 4-tBuC6H4 (3), 4-MeOC6H4 (4), and 4-Me2NC6H4 (5). The homoleptic copper(I) complexes [CuL2][PF6] (L = 1–5) were synthesized and characterized, and the single crystal structure of [Cu(1)2][PF6]·Et2O was determined. By using the “surfaces-as-ligands, surfaces-as-complexes” (SALSAC) approach, the heteroleptic complexes [Cu(6)(Lancillary)]+ in which 6 is the anchoring ligand ((6,6′-dimethyl-[2,2′-bipyridine]-4,4′-diyl)bis(4,1-phenylene))bis(phosphonic acid)) and Lancillary = 1–5 were assembled on FTO-TiO2 electrodes and incorporated as dyes into n-type dye-sensitized solar cells (DSCs). Data from triplicate, fully-masked DSCs for each dye revealed that the best-performing sensitizer is [Cu(6)(1)]+, which exhibits photoconversion efficiencies (η) of up to 1.51% compared to 5.74% for the standard reference dye N719. The introduction of the electron-donating MeO and Me2N groups (Lancillary = 4 and 5) is detrimental, leading to a decrease in the short-circuit current densities and external quantum efficiencies of the solar cells. In addition, a significant loss in open-circuit voltage is observed for DSCs sensitized with [Cu(6)(5)]+, which contributes to low values of η for this dye. Comparisons between performances of DSCs containing [Cu(6)(1)]+ and [Cu(6)(4)]+ with those sensitized by analogous dyes lacking the imine bond indicate that the latter prevents efficient electron transfer across the dye.

Sign in / Sign up

Export Citation Format

Share Document