Cutting force, tool life and surface integrity in milling of titanium alloy Ti-6Al-4V with coated carbide tools

2014 ◽  
Vol 230 (4) ◽  
pp. 694-700 ◽  
Author(s):  
Wilma Polini ◽  
Sandro Turchetta
Keyword(s):  
Titanium Alloy ◽  
Cutting Force ◽  
Tool Life ◽  
Surface Integrity ◽  
Coated Carbide ◽  
Coated Carbide Tools

Tool Wear and Surface Integrity in High Speed Milling of Forging and Cast TA15 Alloys with Coated Carbide Tools

2009 ◽  
Vol 626-627 ◽  
pp. 189-194
Author(s):  
P. Liu ◽  
Jiu Hua Xu ◽  
Yu Can Fu
Keyword(s):  
Titanium Alloy ◽  
Tool Life ◽  
Surface Integrity ◽  
High Speed ◽  
Cutting Tools ◽  
High Speed Milling ◽  
Alpha Titanium ◽  
Series Of Experiments ◽  
Coated Carbide ◽  
Coated Carbide Tools

TA15 (Ti-6.5Al-2Zr-1Mo-1V) is a close alpha titanium alloy strengthened by solid solution with Al and other component. A series of experiments were carried out on normal and high speed milling of TA15. The recommended tools for many years had been the uncoated tungsten carbide grade K. In this work, the tool life of coated carbide tools used in high speed milling of forging and cast titanium alloy was studied. Additionally, the wear mechanism of cutting tools was also discussed. Finally, surface integrity, including surface roughness, metallograph and work hardening, were examined and analyzed. The result shows that the surface quality of forging and cast machined by carbide cutter is similar, but the tool life of carbide in high speed milling of forging TA15 is longer than that in high speed milling of cast TA15.

Comparative assessment between AlTiN and AlTiSiN coated carbide tools towards machinability improvement of AISI D6 steel in dry hard turning

2021 ◽  
pp. 095440622110373
Author(s):  
Anshuman Das ◽  
Miyaz Kamal ◽  
Sudhansu Ranjan Das ◽  
Saroj Kumar Patel ◽  
Asutosh Panda ◽  
...  
Keyword(s):  
Cutting Force ◽  
Tool Life ◽  
Hard Turning ◽  
Flank Wear ◽  
Chip Morphology ◽  
Comparative Assessment ◽  
Carbide Tool ◽  
Crater Wear ◽  
Coated Carbide ◽  
Coated Carbide Tools

AISI D6 (hardness 65 HRC) is one of the hard-to-cut steel alloys and commonly used in mould and die making industries. In general, CBN and PCBN tools are used for machining hardened steel but its higher cost makes the use for limited applications. However, the usefulness of carbide tool with selective coatings is the best substitute having comparable tool life, and in terms of cost is approximately one-tenth of CBN tool. The present study highlights a detailed analysis on machinability investigation of hardened AISI D6 alloy die steel using newly developed SPPP-AlTiSiN coated carbide tools in finish dry turning operation. In addition, a comparative assessment has been performed based on the effectiveness of cutting tool performance of nanocomposite coating of AlTiN deposited by hyperlox PVD technique and a coating of AlTiSiN deposited by scalable pulsed power plasma (SPPP) technique. The required number of machining trials under varied cutting conditions (speed, depth of cut, feed) were based on L16 orthogonal array design which investigated the crater wear, flank wear, surface roughness, chip morphology, and cutting force in hard turning. Out of the two cutting tools, newly-developed nanocomposite (SPPP-AlTiSiN) coated carbide tool promises an improved surface finish, minimum cutting force, longer tool life due to lower value of crater & flank wears, and considerable improvement in tool life (i.e., by 47.83%). At higher cutting speeds, the crater wear length and flank wear increases whereas the surface roughness, crater wear width and cutting force decreases. Chip morphology confirmed the formation of serrated type saw tooth chips.

Study on the Tool Wear of Coated Carbide Tool in High Speed Milling Titanium Alloy

2014 ◽  
Vol 800-801 ◽  
pp. 526-530 ◽  
Author(s):  
Shu Cai Yang ◽  
Yu Hua Zhang ◽  
Quan Wan ◽  
Jian Jun Chen ◽  
Chuang Feng
Keyword(s):  
Titanium Alloy ◽  
Tool Wear ◽  
Tool Life ◽  
High Speed ◽  
Carbide Tool ◽  
High Speed Milling ◽  
Coated Carbide Tool ◽  
Fluid Environment ◽  
Coated Carbide ◽  
Coated Carbide Tools

The milling experiments were carried out using TiAlN and PCD coated carbide tools in high speed milling Ti6Al4V to compare and analyze tool wear and tool life of the two kinds of coating carbide tools. In addition, the effect of cooling and lubricating on tool wear is also studied. The results showed that fluid environment is not suitable for milling Ti6Al4V. PCD coating carbide tool can effectively increase the life of tool in high speed milling of Ti6Al4V.

Cutting Performance of Cemented Carbide Tool in High-Efficiency Turning Ti6Al4V

2012 ◽  
Vol 522 ◽  
pp. 231-235 ◽  
Author(s):  
Yi Hang Fan ◽  
Min Li Zheng ◽  
Zhe Li ◽  
Song Tao Wang ◽  
Ying Bin Li
Keyword(s):  
Titanium Alloy ◽  
Tool Wear ◽  
Cutting Force ◽  
Tool Life ◽  
Cutting Temperature ◽  
Cutting Performance ◽  
Cemented Carbide ◽  
Carbide Tool ◽  
Cemented Carbide Tool ◽  
Coated Carbide

The machining efficiency of titanium alloy Ti6Al4V is low and the tool wear is serious. In this paper, uncoated carbide tool and two kinds of coated cemented carbide tool were used for dry turning titanium alloy. The experiments used CCD Observing System and the EDAX analysis of SEM to study tool wear mechanism and analyze the cutting performance through tool life, cutting force and cutting temperature. The results show that the main wear reasons are adhesion, diffusion and oxidation wear. For coated tool, the coating peeled off first, and then tool substrate damaged. Compared with coated carbide tool, the uncoated carbide tool with fine grain has longer tool life and lower cutting force and cutting temperature. The changes of cutting force and cutting temperature with cutting speed are not obvious when using the ccomposite coating (TiAlN and AlCrN) carbide tool. The results can help to choose tool material reasonably and control tool wear.

scholarly journals Research on Cutting Force and Surface Integrity of TC18 Titanium Alloy by Longitudinal Ultrasonic Vibration Assisted Milling

2021 ◽  
Author(s):  
Weibo Xie ◽  
Xikui Wang ◽  
Erbo Liu ◽  
Jian Wang ◽  
Xiaobin Tang ◽  
...  
Keyword(s):  
Titanium Alloy ◽  
Cutting Force ◽  
Ultrasonic Vibration ◽  
Surface Integrity ◽  
Rotational Speed ◽  
Three Dimensional ◽  
Cutting Temperature ◽  
Surface Residual Stress ◽  
Deformation Layer ◽  
Vibration Milling

Abstract In order to study the influence of rotational speed and amplitude on the surface integrity, TC18 titanium alloy samples were milled by the process of conventional milling and longitudinal ultrasonic vibration assisted milling. The experimental data were obtained by dynamometer, thermometer, scanning electron microscope, X-ray diffractometer and three-dimensional surface topography instrument for observation and analysis. The results show that the rotational speed has a significant effect on the cutting force, cutting temperature, surface morphology and surface residual stress. Compared with ordinary milling, the surface micro-texture produced by ultrasonic vibration milling is more regular, , and with the increase of rotational speed, the influence of ultrasonic vibration on cutting force and cutting temperature decrease. There are adverse effects on surface roughness after ultrasonic vibration superposition. The influence of ultrasonic vibration on the surface residual compressive stress is also greatly reduced when the rotational speed is greater than 2400 rpm. In addition, a certain depth of plastic deformation layer can be formed under the surface of ultrasonic vibration machining, and the depth of deformation layer increases with the increase of vibration.

Comparative Experimental Research on Cutting Superalloy Used New Coated Carbide Tools

2010 ◽  
Vol 33 ◽  
pp. 173-176
Author(s):  
X.Y. Wang ◽  
S.Q. Pang ◽  
Q.X. Yu
Keyword(s):  
Tool Wear ◽  
Tool Life ◽  
Experimental Research ◽  
Cutting Tools ◽  
Cutting Speed ◽  
Life Testing ◽  
Processing Efficiency ◽  
Comparative Tests ◽  
Coated Carbide ◽  
Coated Carbide Tools

The aim of this work is to investigate the machinability of new coated carbide cutting tools that are named C7 plus coatings under turning of superalloy GH2132. This achieved by analysis of tool life at different cutting conditions .Investigations of tool wear and tool life testing are intended to establish T-V formulas, and then analyzed the characteristics of coating . Through a series of comparative tests, Using TiAlN coatings as the contrast materialthe results show that the new coating tools that are named C7 plus coatings are suitable for cutting superalloy GH2132. The cutting speed and processing efficiency can be increased effectively.

Cutting Performance and Failure Mechanisms of Coated Carbide Tools in Face Milling Powder Metallurgy Nickel-Based Superalloy

2012 ◽  
Vol 497 ◽  
pp. 94-98
Author(s):  
Yang Qiao ◽  
Xiu Li Fu ◽  
Xue Feng Yang
Keyword(s):  
Cutting Force ◽  
Feed Rate ◽  
Failure Mechanisms ◽  
Cutting Temperature ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Face Milling ◽  
Nickel Based Superalloy ◽  
Coated Carbide ◽  
Coated Carbide Tools

Powder metallurgy (PM) nickel-based superalloy is regarded as one of the most important aerospace industry materials, which has been widely used in advanced turbo-engines. This work presents an orthogonal design experiments to study the cutting force and cutting temperature variations in the face milling of PM nickel-based superalloy with PVD coated carbide tools. Experimental results show that with the increase of feed rate and depth of cut, there is a growing tendency in cutting force, with the increase of cutting speed, cutting force decreases. Among the cutting parameters, feed rate has the greatest influence on cutting force, especially when cutting speed exceeds 60m/min. With the increase of all the cutting parameters, cutting temperature increases. However the cutting temperature increases slightly as the increasing of feed rate. Tool failure mechanisms in face milling of PM nickel-based superalloy are analyzed. It is shown that the breakage and spalling on the cutting edge are the most dominate failure mechanisms, which dominates the deterioration and final failure of the coated carbide tools.

High-Quality End Milling of CFRP – Inclination Milling with High-Helix End Mill –

2016 ◽  
Vol 10 (3) ◽  
pp. 372-380 ◽  
Author(s):  
Akira Hosokawa ◽  
◽  
Naoya Hirose ◽  
Takashi Ueda ◽  
Tomohiro Koyano ◽  
...  
Keyword(s):  
Tool Wear ◽  
Cutting Force ◽  
Surface Integrity ◽  
Helix Angle ◽  
Surface Generation ◽  
End Mill ◽  
Side Milling ◽  
Pull Out ◽  
End Mills ◽  
Coated Carbide

Side milling tests of CFRP (carbon fiber reinforced plastics) containing thermosetting resin are carried out by TiAlN/AlCrN-coated, H2-free DLC (diamond-like carbon)-coated, and CVD diamond-coated carbide end mills without coolant. Two types of end mills having different helix angles of 30° and 60° are used. The film thickness and surface smoothness are varied for the DLC-coated end mills. The cutting characteristics are evaluated by tool wear and surface integrity (i.e., 3D profiles of the machined surface, generation of fluffing, delamination, and pull-out of the carbon fibers). The cutting force and tool flank temperature are also examined for the two types of CFRP composites and the helix angle of the end mill. “Inclination milling,”in which the end mill is tilted so that the resultant cutting force acts parallel to the work surface, is proposed as a novel technique to be used with a high-helix angle end mill. This unique approach enables the reduction of tool wear and improves the surface integrity of machined CFRP surfaces.

Sign in / Sign up

Export Citation Format

Share Document