Performance evaluation and entropy generation of chevron-type plate-fin equipped with ribs and holes

2021 ◽  
pp. 095440622110127
Author(s):  
F Nejati Barzoki ◽  
M Khoshvaght-Aliabadi ◽  
GA Sheikhzadeh ◽  
AA Abbasian Arani ◽  
A Feizabadi
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Pressure Drop ◽  
Entropy Generation ◽  
Geometrical Parameters ◽  
Bejan Number ◽  
Entropy Generation Number ◽  
Generation Number ◽  
Performance Indexes ◽  
The Relationship

The complexity caused by an enhanced technique may significantly enhance the heat transfer along with a penalty in the pressure drop. Thus, it is needed to assess the counteracting effects between the enhanced heat transfer and the augmented pressure drop in practical applications. In order to comprehensively evaluate the hydrothermal performance of the chevron-type plate-fin (CTPF) equipped with ribs and holes, this study focuses on the relationship between hydraulic and thermal characteristics. Firstly, the relationship between the Colburn factor and the friction factor is presented, then two performance indexes are applied using these factors to evaluate the use of ribs and holes in the CTPIt F is found that the simultaneous use of ribs and holes shows better overall performances as compared with the use of ribs or holes individually. At the same geometrical parameters, the highest values of 1.52 and 1.07 are recorded for these performance indexes. In order to further improve the overall performance of the CTPF, the effects of geometrical parameters are also investigated. With the decrease of corrugation amplitude ( a) and the increase of corrugation length ( l), rib height ( h), and rib thickness ( t), the CTPF performs better overall performances. And, for the models with different levels of hole width ( w), the better performance is seen when this parameter is at the middle level. However, in the studied models, the best overall hydrothermal performance is detected for the model with a = 2.5 mm, l = 60 mm, h = 2.5 mm, t = 10 mm, and w = 10 mm, and highest performance indexes of 2.52 and 1.15 are reported for this model. Likewise, an entropy generation analysis is carried out, and the obtained results are discussed based on the Bejan number and entropy generation number. The results show that the increase of Reynolds number can lead to decrease of Bejan number and to increase of entropy generation number. For Reynolds number ranging from 4000 to 10000, the best model, which is described above, shows 17% decrease in the entropy generation number comparing with the reference model. Finally, two correlations are developed to predict the Bejan number and entropy generation number of the current study.

Thermodynamic optimization of nanofluid flow over a non-isothermal wedge with nonlinear radiation and activation energy

2021 ◽  
Author(s):  
M R Acharya ◽  
P Mishra ◽  
Satyananda Panda
Keyword(s):  
Heat Transfer ◽  
Activation Energy ◽  
Reynolds Number ◽  
Entropy Generation ◽  
Volume Fraction ◽  
Mathematical Formulation ◽  
Bejan Number ◽  
Nanofluid Flow ◽  
Entropy Generation Number ◽  
Generation Number

Abstract This paper analyses the augmentation entropy generation number for a viscous nanofluid flow over a non-isothermal wedge including the effects of non-linear radiation and activation energy. We discuss the influence of thermodynamically important parameters during the study, namely, the Bejan number, entropy generation number, and the augmentation entropy generation number. The mathematical formulation for thermal conductivity and viscosity of nanofluid for Al2O3 − EG mixture has been considered. The results were numerically computed using implicit Keller-Box method and depicted graphically. The important result is the change in augmentation entropy generation number with Reynolds number. We observed that adding nanoparticles (volume fraction) tend to enhance augmentation entropy generation number for Al2O3 − EG nanofluid. Further, the investigation on the thermodynamic performance of non-isothermal nanofluid flow over a wedge reveals that adding nanoparticles to the base fluid is effective only when the contribution of heat transfer irreversibility is more than fluid friction irreversibility. This work also discusses the physical interpretation of heat transfer irreversibility and pressure drop irreversibility. This dependency includes Reynolds number and volume fraction parameter. Other than these, the research looked at a variety of physical characteristics associated with the flow of fluid, heat and mass transfer.

scholarly journals Comprehensive performance investigation and optimization of a plate fin heat exchanger with wavy fins

2021 ◽  
pp. 322-322
Author(s):  
Mengmeng Cui ◽  
Rui Song
Keyword(s):  
Heat Transfer ◽  
Heat Exchanger ◽  
Pump Power ◽  
Pressure Drop ◽  
Objective Function ◽  
Entropy Generation ◽  
Entropy Generation Number ◽  
Generation Number ◽  
Comprehensive Performance ◽  
Modified Entropy

As the pressure drop and pump power increase with the enhancement of heat transfer, it is of great value to investigate the comprehensive performance of the heat exchanger based on common accurate correlations of heat transfer and flow friction. This paper adopts a generalized air-side thermal-hydraulic correlation to study the comprehensive performances of the plate fin heat exchanger with wavy fins. To better understand the fin characteristics, performance indexes under the same flow rate, pressure drop and pump power are employed to estimate the comprehensive flow and heat transfer performances. The nonlinear optimization problem is established in consideration of the multiple independent variables with the maximum effectiveness or the minimum modified entropy generation number as the optimization objective function, which is solved by the genetic algorithm. Comparative analysis is conducted for results obtained from the parametric analysis and heat exchanger optimization, indicating that the objective function of the modified entropy generation number is effective for the design optimization of the comprehensive performance.

scholarly journals Thermodynamical Analysis of the Flow and Heat Transfer over a Static and a Moving Wedge

2013 ◽  
Vol 2013 ◽  
pp. 1-6 ◽  
Author(s):  
Adnan Saeed Butt ◽  
Asif Ali
Keyword(s):  
Heat Transfer ◽  
Entropy Generation ◽  
Temperature Fields ◽  
Entropy Production Rate ◽  
Physical Parameters ◽  
Bejan Number ◽  
Entropy Generation Number ◽  
Flow And Heat Transfer ◽  
Generation Number ◽  
Moving Wedge

The first and second law characteristics of fluid flow and heat transfer over a static and a moving wedge are investigated. With the help of suitable similarity transformations, the governing boundary layer equations for the velocity and temperature fields are transformed into ordinary differential equations and are solved numerically. The velocity and the temperature profiles are obtained for various parameters and are utilized to compute the entropy generation number Ns and the Bejan number Be. The effects of various physical parameters on the entropy generation number and the Bejan number are depicted through graphs and are discussed qualitatively. It is observed that the entropy production rate is less in case of wedge moving in the opposite direction to flow as compared to static wedge.

scholarly journals Analytical study of parameters affecting entropy generation of nanofluid turbulent flow in channel and micro-channel

2016 ◽  
Vol 20 (6) ◽  
pp. 2037-2050 ◽  
Author(s):  
Ghanbarali Sheikhzadeh ◽  
Alireza Aghaei ◽  
Hamidreza Ehteram ◽  
Mahmoud Abbaszadeh
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Turbulent Flow ◽  
Tio2 Nanoparticles ◽  
Entropy Generation ◽  
Volume Fraction ◽  
Geometrical Parameters ◽  
Bejan Number ◽  
Micro Channel ◽  
Minimum Entropy

In this study, thermo-physical and geometrical parameters affecting entropy generation of nanofluid turbulent flow such as the volume fraction, Reynolds number and diameter of the channel and micro-channel with circular cross section under constant flux are examined analytically. Water is used as a base fluid of nanofluid with nanoparticles of Ag, Cu, CuO and TiO2. The study is conducted for Reynolds numbers of 20000, 40000 and 100000, volume fractions of 0, 0.01, 0.02, 0.03 and 0.04, channel diameters of 2, 4, 6 and 8 cm and micro-channel diameters of 20, 40, 60 and 80 micrometers. Based on the results, the most of the generated entropy in channel is due to heat transfer, and also, with increasing the diameter of the channel, Bejan number increases. The contribution of entropy generation due to heat transfer in the micro-channel is very poor and the major contribution of entropy generation is due to friction. The maximum amount of entropy generation in channel belongs to nanofluids with Ag, Cu, CuO and TiO2 nanoparticles, respectively, while in the micro-channel this behavior is reversed; and the minimum entropy generation happens in nanofluids with Ag, Cu, CuO and TiO2 nanoparticles, respectively. In channel and micro-channel, for all nanofluids except for the water-TiO2, with increasing volume fraction of nanoparticles, the entropy generation decreases. In channel and micro-channel, the total entropy generation increases as Reynolds number augments.

scholarly journals Entropy analysis in moving wavy surface boundary-layer

2019 ◽  
Vol 23 (1) ◽  
pp. 233-241 ◽  
Author(s):  
Ahmer Mehmood ◽  
Muhammad Iqbal ◽  
Sajid Khan ◽  
Sufian Munawar
Keyword(s):  
Heat Transfer ◽  
Entropy Generation ◽  
Wavy Surface ◽  
Bejan Number ◽  
Surface Boundary ◽  
Surface Boundary Layer ◽  
Entropy Generation Number ◽  
Keller Box Method ◽  
Generation Number ◽  
Group Parameter

It is a well-established fact that significant gain in the heat transfer rate can be obtained by altering that flat surface texture of the working body. The most convenient alteration, in view of mathematical handling, is the wavy one. Existing studies reveal that the convective heat transfer phenomenon is affected significantly due to the presence of a solid wavy surface. How does the phenomena of entropy generation is effected due to a wavy surface is the question investigated in this manuscript. The expressions for irreversibility distribution rate, Bejan number, and volumetric entropy generation number have been evaluated by Keller-Box method. The effect of important parameters of interest, such as wavy amplitude, Prandtl number, and group parameter on irreversibility distribution rate, Bejan number and entropy generation number, have been discussed in detail. The study reveals that entropy generation number decreases and irreversibility rate increases by increasing the amplitude of the wavy surface.

Entropy generation and heat transfer analysis for ferrofluid flow between two rotating disks with variable conductivity

2021 ◽  
pp. 095440622199118
Author(s):  
Anupam Bhandari
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Differential Equations ◽  
Entropy Generation ◽  
Heat Transfer Analysis ◽  
Entropy Generation Rate ◽  
Geometrical Parameters ◽  
Rotating Disks ◽  
Coupled Differential Equations ◽  
Lower Disk

Present model analyze the flow and heat transfer of water-based carbon nanotubes (CNTs) [Formula: see text] ferrofluid flow between two radially stretchable rotating disks in the presence of a uniform magnetic field. A study for entropy generation analysis is carried out to measure the irreversibility of the system. Using similarity transformation, the governing equations in the model are transformed into a set of nonlinear coupled differential equations in non-dimensional form. The nonlinear coupled differential equations are solved numerically through the finite element method. Variable viscosity, variable thermal conductivity, thermal radiation, and volume concentration have a crucial role in heat transfer enhancement. The results for the entropy generation rate, velocity distributions, and temperature distribution are graphically presented in the presence of physical and geometrical parameters of the flow. Increasing the values of ferromagnetic interaction number, Reynolds number, and temperature-dependent viscosity enhances the skin friction coefficients on the surface and wall of the lower disk. The local heat transfer rate near the lower disk is reduced in the presence of Harman number, Reynolds number, and Prandtl number. The ferrohydrodynamic flow between two rotating disks might be useful to optimize the use of hybrid nanofluid for liquid seals in rotating machinery.

scholarly journals Analytical Assessment of (Al2O3–Ag/H2O) Hybrid Nanofluid Influenced by Induced Magnetic Field for Second Law Analysis with Mixed Convection, Viscous Dissipation and Heat Generation

Coatings ◽  
2021 ◽  
Vol 11 (5) ◽  
pp. 498
Author(s):  
Wasim Ullah Khan ◽  
Muhammad Awais ◽  
Nabeela Parveen ◽  
Aamir Ali ◽  
Saeed Ehsan Awan ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Viscous Dissipation ◽  
Entropy Generation ◽  
Heat Generation ◽  
Transfer Rate ◽  
Second Law ◽  
Hybrid Nanofluid ◽  
Entropy Generation Number ◽  
Generation Number ◽  
Second Law Analysis

The current study is an attempt to analytically characterize the second law analysis and mixed convective rheology of the (Al2O3–Ag/H2O) hybrid nanofluid flow influenced by magnetic induction effects towards a stretching sheet. Viscous dissipation and internal heat generation effects are encountered in the analysis as well. The mathematical model of partial differential equations is fabricated by employing boundary-layer approximation. The transformed system of nonlinear ordinary differential equations is solved using the homotopy analysis method. The entropy generation number is formulated in terms of fluid friction, heat transfer and Joule heating. The effects of dimensionless parameters on flow variables and entropy generation number are examined using graphs and tables. Further, the convergence of HAM solutions is examined in terms of defined physical quantities up to 20th iterations, and confirmed. It is observed that large λ1 upgrades velocity, entropy generation and heat transfer rate, and drops the temperature. High values of δ enlarge velocity and temperature while reducing heat transport and entropy generation number. Viscous dissipation strongly influences an increase in flow and heat transfer rate caused by a no-slip condition on the sheet.

scholarly journals Optimal Design of Nanoparticle Enhanced Phan-Thien–Tanner Flow of a Viscoelastic Fluid in a Microchannel

Entropy ◽  
2018 ◽  
Vol 20 (12) ◽  
pp. 895
Author(s):  
Mohammad Abdollahzadeh Jamalabadi
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Entropy Generation ◽  
Volume Fraction ◽  
Circular Cross Section ◽  
Major Influence ◽  
Parameter Study ◽  
Bejan Number ◽  
Total Entropy ◽  
Minimum Entropy

The excellent thermal characteristics of nanoparticles have increased their application in the field of heat transfer. In this paper, a thermophysical and geometrical parameter study is performed to minimize the total entropy generation of the viscoelastic flow of nanofluid. Entropy generation with respect to volume fraction (<0.04), the Reynolds number (20,000–100,000), and the diameter of the microchannel (20–20,000 μm) with the circular cross-section under constant flux are calculated. As is shown, most of the entropy generation owes to heat transfer and by increasing the diameter of the channel, the Bejan number increases. The contribution of heat entropy generation in the microchannel is very poor and the major influence of entropy generation is attributable to friction. The maximum quantity of in-channel entropy generation happens in nanofluids with TiO2, CuO, Cu, and Ag nanoparticles, in turn, despite the fact in the microchannel this behavior is inverted, the minimum entropy generation occurs in nanofluids with CuO, Cu, Ag, and TiO2 nanoparticles, in turn. In the channel and microchannel for all nanofluids except water-TiO2, increasing the volume fraction of nanoparticles decreases entropy generation. In the channel and microchannel the total entropy generation increases by augmentation the Reynolds number.

Second law analysis of magneto-natural convection in a nanofluid filled wavy-hexagonal porous enclosure

2020 ◽  
Vol 30 (11) ◽  
pp. 4811-4836 ◽  
Author(s):  
Seyyed Masoud Seyyedi ◽  
A.S. Dogonchi ◽  
M. Hashemi-Tilehnoee ◽  
D.D. Ganji ◽  
Ali J. Chamkha
Keyword(s):  
Heat Transfer ◽  
Natural Convection ◽  
Entropy Generation ◽  
Average Nusselt Number ◽  
Convection Heat Transfer ◽  
Natural Convection Heat Transfer ◽  
Content Type ◽  
Entropy Generation Number ◽  
Maximum Value ◽  
Generation Number

Purpose Natural convection heat transfer analysis can be completed using entropy generation analysis. This study aims to accomplish both the natural convection heat transfer and entropy generation analyses for a hexagonal cavity loaded with Cu-H2O nanoliquid subjected to an oriented magnetic field. Design/methodology/approach Control volume-based finite element method is applied to solve the non-dimensional forms of governing equations and then, the entropy generation number is computed. Findings The results portray that both the average Nusselt and entropy generation numbers boost with increasing aspect ratio for each value of the undulation number, while both of them decrease with increasing the undulation number for each amplitude parameter. There is a maximum value for the entropy generation number at a specified value of Hartmann number. Also, there is a minimum value for the entropy generation number at a specified value of angle of the magnetic field. When the volume fraction of nanoparticles grows, the average Nusselt number increases and the entropy generation number declines. The entropy generation number attains to a maximum value at Ha = 14 for each value of aspect ratio. The average Nusselt number ascends 2.9 per cent and entropy generation number decreases 1.3 per cent for Ha = 0 when ϕ increases from 0 to 4 per cent. Originality/value A hexagonal enclosure (complex geometry), which has many industrial applications, is chosen in this study. Not only the characteristics of heat transfer are investigated but also entropy generation analysis is performed in this study. The ecological coefficient of performance for enclosures is calculated, too.

Numerical Investigation of Local Entropy Generation for Laminar Flow in Rotating-Disk Systems

2010 ◽  
Vol 132 (9) ◽  
Author(s):  
Mohammad Shanbghazani ◽  
Vahid Heidarpoor ◽  
Marc A. Rosen ◽  
Iraj Mirzaee
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Laminar Flow ◽  
Entropy Generation ◽  
Generation Rate ◽  
Entropy Generation Rate ◽  
Bejan Number ◽  
Local Entropy ◽  
Fluid Friction ◽  
Local Entropy Generation

The entropy generation is investigated numerically in axisymmetric, steady-state, and incompressible laminar flow in a rotating single free disk. The finite-volume method is used for solving the momentum and energy equations needed for the determination of the entropy generation due to heat transfer and fluid friction. The numerical model is validated by comparing it to previously reported analytical and experimental data for momentum and energy. Results are presented in terms of velocity distribution, temperature, local entropy generation rate, Bejan number, and irreversibility ratio distribution for various rotational Reynolds number and physical cases, using dimensionless parameters. It is demonstrated that increasing rotational Reynolds number increases the local entropy generation rate and irreversibility rate, and that the irreversibility is mainly due to heat transfer while the irreversibility associated with fluid friction is minor.

Sign in / Sign up

Export Citation Format

Share Document