Component mode synthesis methods for a body-in-white noise and vibration analysis

2016 ◽  
Vol 231 (2) ◽  
pp. 279-288 ◽  
Author(s):  
Simone Vizzini ◽  
Magnus Olsson ◽  
Alessandro Scattina
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Element Model ◽  
The Body ◽  
Component Mode Synthesis ◽  
Synthesis Methods ◽  
Dynamic Substructuring ◽  
Reduction Methods ◽  
Body In White ◽  
Noise Vibration

In this work the dynamic substructuring approach was applied to a noise, vibration and harshness problem within the automotive engineering field. In particular, a noise, vibration and harshness analysis was carried out on the body-in-white structure of a passenger car. The work focuses on the theory of component mode synthesis. Two component mode synthesis reduction methods, namely the Craig–Bampton method and the Craig–Chang method, were applied to the body-in-white structure of the Volvo V40. The influences of various parameters were investigated. In particular, the effect of the reduction basis on the response accuracy and on the reduction time was studied. Moreover, the effects of the connection properties between different parts of the model were examined. The simulation times of the reduced models and of the full finite element model were compared. The results showed that the Craig–Chang method performs better when the modes are retained for up to one and a half times the maximum frequency response studied. Additionally, the Craig–Chang method gives a very accurate representation of the system dynamics even when connections with a low stiffness are used. Finally, it is possible to reduce the simulation time by up to 90% if component mode synthesis methods are used instead of the full finite element model.

Model Analysis of Car’s Body-in-White Based on FEA

2011 ◽  
Vol 354-355 ◽  
pp. 454-457
Author(s):  
Yuan Wang ◽  
Li Xu ◽  
Xi Liang Dai ◽  
Sheng Hui Peng
Keyword(s):  
Finite Element ◽  
Optimal Design ◽  
Finite Element Model ◽  
Element Model ◽  
Model Analysis ◽  
The Body ◽  
Dynamic Parameters ◽  
Modal Test ◽  
Body In White ◽  
The Finite Element Model

In this paper, the finite element model of some car’s body-in-white is established in Hypermesh. The model analysis is executed based on the element model in ANSYS. Through the model analysis the dynamic parameters of the body-in-white are obtained. At the same time，the modal test of a real car body is implemented. The reliability of the finite element model is validated based on the modal test. The results show that the stiffness of the body-in-white is great enough and it can provide optimal design for future designers.

The Concept modeling method: An approach to optimize the structural dynamics of a vehicle body

2020 ◽  
Vol 234 (13) ◽  
pp. 2923-2932 ◽  
Author(s):  
Mohammad Fard ◽  
Jianchun Yao ◽  
Richard Taube ◽  
John Laurence Davy
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Structural Dynamics ◽  
Element Model ◽  
Modeling Method ◽  
The Body ◽  
Vehicle Body ◽  
Concept Model ◽  
Body In White ◽  
Concept Modeling

Although the concept modeling method has already been proposed in the literature, there is still very limited knowledge about the validation and the application of this method for vehicle body design. This paper substantially increases this limited knowledge by developing a concept model for predicting and optimizing the structural dynamics of a vehicle body-in-white and validating this concept model against a detailed finite element model. The geometry and parameters of the concept model are extracted from its detailed finite element model. The major members and panels of the detailed finite element model are replaced by their equivalent beam and shell elements models. The joints of the concept model are represented by stiffness and mass matrices extracted from the detailed finite element model using the Guyan Reduction Method. The developed concept model is validated by comparing its structural dynamics, including the resonant frequencies and the vibration mode shapes, with the original detailed finite element model and the experimental results. The simplicity and small size of the concept model enable it to easily enhance the structural dynamics of the body-in-white by optimizing the cross-sections of the load-carrying members of the structure. The optimization in this case increased the resonant frequencies of the body-in-white while reducing the total mass by about 6 kg. The results prove that the concept modeling method can significantly enhance the body-in-white structural dynamics by reducing the complexity of the model and allowing the focus for the optimization to be on the main members of the structure at the development stage when the final design parameters are not well known and have not been fixed.

scholarly journals Vibration-based Bayesian model updating of civil engineering structures applying Gaussian process metamodel

2019 ◽  
Vol 22 (16) ◽  
pp. 3487-3502
Author(s):  
Hossein Moravej ◽  
Tommy HT Chan ◽  
Khac-Duy Nguyen ◽  
Andre Jesus
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Bayesian Approach ◽  
Model Updating ◽  
Numerical Models ◽  
Element Model ◽  
The Body ◽  
Structural Safety ◽  
Discrepancy Function ◽  
The Finite Element Model

Structural health monitoring plays a significant role in providing information regarding the performance of structures throughout their life spans. However, information that is directly extracted from monitored data is usually susceptible to uncertainties and not reliable enough to be used for structural investigations. Finite element model updating is an accredited framework that reliably identifies structural behavior. Recently, the modular Bayesian approach has emerged as a probabilistic technique in calibrating the finite element model of structures and comprehensively addressing uncertainties. However, few studies have investigated its performance on real structures. In this article, modular Bayesian approach is applied to calibrate the finite element model of a lab-scaled concrete box girder bridge. This study is the first to use the modular Bayesian approach to update the initial finite element model of a real structure for two states—undamaged and damaged conditions—in which the damaged state represents changes in structural parameters as a result of aging or overloading. The application of the modular Bayesian approach in the two states provides an opportunity to examine the performance of the approach with observed evidence. A discrepancy function is used to identify the deviation between the outputs of the experimental and numerical models. To alleviate computational burden, the numerical model and the model discrepancy function are replaced by Gaussian processes. Results indicate a significant reduction in the stiffness of concrete in the damaged state, which is identical to cracks observed on the body of the structure. The discrepancy function reaches satisfying ranges in both states, which implies that the properties of the structure are predicted accurately. Consequently, the proposed methodology contributes to a more reliable judgment about structural safety.

Two-dimensional finite element model to study temperature distribution in peripheral regions of extended spherical human organs involving uniformly perfused tumors

2015 ◽  
Vol 08 (06) ◽  
pp. 1550074 ◽  
Author(s):  
Akshara Makrariya ◽  
Neeru Adlakha
Keyword(s):  
Finite Element ◽  
Temperature Distribution ◽  
Finite Element Model ◽  
Metabolic Activity ◽  
Element Model ◽  
The Body ◽  
Tissue Response ◽  
Two Dimensional ◽  
Human Breast ◽  
Peripheral Regions

Temperature as an indicator of tissue response is widely used in clinical applications. In view of above a problem of temperature distribution in peripheral regions of extended spherical organs of a human body like, human breast involving uniformly perfused tumor is investigated in this paper. The human breast is assumed to be spherical in shape with upper hemisphere projecting out from the trunk of the body and lower hemisphere is considered to be a part of the body core. The outer surface of the breast is assumed to be exposed to the environment from where the heat loss takes place by conduction, convection, radiation and evaporation. The heat transfer from core to the surface takes place by thermal conduction and blood perfusion. Also metabolic activity takes place at different rates in different layers of the breast. An elliptical-shaped tumor is assumed to be present in the dermis region of human breast. A finite element model is developed for a two-dimensional steady state case incorporating the important parameters like blood flow, metabolic activity and thermal conductivity. The triangular ring elements are employed to discretize the region. Appropriate boundary conditions are framed using biophysical conditions. The numerical results are used to study the effect of tumor on temperature distribution in the region.

Dynamic Analysis of Flexible Structures Using Component Mode Synthesis

1989 ◽  
Vol 56 (4) ◽  
pp. 874-880 ◽  
Author(s):  
M. De Smet ◽  
C. Liefooghe ◽  
P. Sas ◽  
R. Snoeys
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Degrees Of Freedom ◽  
Flexible Structures ◽  
Element Model ◽  
Component Mode Synthesis ◽  
Mode Shapes ◽  
Flexible Robot ◽  
Preliminary Calculation ◽  
Resonance Frequencies

In this paper a dynamic model of a flexible robot is built out of a finite element model of each of its links. The number of degrees-of-freedom of these models is strongly reduced by applying the Component Mode Synthesis technique which involves the preliminary calculation of a limited number of mode shapes of the separate links. As can be seen from examples, the type of boundary conditions thereby imposed in the nodes in which one link is connected to the others, strongly determines the accuracy of the calculated resonance frequencies of the robot. The method is applied to an industrial manipulator. The reduced finite element model of the robot is changed in order to match the numerically and experimentally (modal analysis) determined resonance data. Further, the influence of the position of the robot on its resonance frequencies is studied using the optimized numerical model.

UNCERTAINTIES OF IMPACT CONFIGURATION FOR NUMERICAL REPLICATIONS OF REAL-WORLD TRAUMA: A FE ANALYSIS

2016 ◽  
Vol 16 (08) ◽  
pp. 1640018 ◽  
Author(s):  
MICHÈLE BODO ◽  
SÉBASTIEN ROTH
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Real World ◽  
Injury Risk ◽  
Body Position ◽  
Free Fall ◽  
Experimental Tests ◽  
Element Model ◽  
The Body ◽  
Thoracic Injury

This study deals with free fall accident analysis involving adults, and their numerical replications using a finite element model of the human thorax. The main purpose is to determine the role of body position at impact in the thorax injury risk appearance. For this study, cases of real-world free-fall provided by an emergency department were selected and investigated. These cases involved both male and female with an age range of 20 to 63 years, who sustained accidental free-fall with both injured and uninjured cases. The examination of the patients' medical record provided helpful information to accurately perform numerical replications with the finite element model HUByx (Hermaphrodite Universal Biomechanical yx model) which was already validated for various experimental tests in the field of automobile, ballistic impacts and blast. The results of simulations at different impact location allowed highlighting the crucial influence of the body orientation in the risk of thoracic injury occurrence.

Ballistic Impact Analysis of the Human Thorax With a Protective Body Armor

2000 ◽  
Author(s):  
Y. W. Kwon ◽  
J. E. Jolly ◽  
T. A. Hughes
Keyword(s):  
Finite Element ◽  
Finite Element Model ◽  
Impact Analysis ◽  
Element Model ◽  
The Body ◽  
Body Armor ◽  
Element Analysis ◽  
Essential Components ◽  
Human Thorax ◽  
Armor System

Abstract The biomechanical response of a finite element model of the human thorax and a protective body armor system was studied under impact loading from a projectile. The objective of the study was to create a viable finite element model of the human thorax. The model was validated by comparing the results of tests of body armor systems conducted on cadavers to results obtained from finite element analysis. A parametric study was undertaken to determine the essential components of the model. The results from this investigation determined that the path of force propagation from a body armor system to the thorax upon bullet impact is directly through the vest to the sternum and then through the skeleton to the rest of the body. Thus, any parameters that affect the components in this pathway were essential to the model. This included the muscles, their geometries, material properties, and viscosity, as well as the Young’s modulus of the sternochondral cartilage and the bones themselves.

Additive manufacturing and topology optimization: A design strategy for a steering column mounting bracket considering overhang constraints

2020 ◽  
pp. 095440622091771
Author(s):  
Sara Mantovani ◽  
Giuseppe A Campo ◽  
Andrea Ferrari
Keyword(s):  
Finite Element ◽  
Topology Optimization ◽  
Additive Manufacturing ◽  
Isotropic Material ◽  
Element Model ◽  
The Body ◽  
Left Hand ◽  
Automotive Body ◽  
Body In White ◽  
Overhang Angle

In the present paper, the use of the topology optimization in a metal Additive Manufacturing application is discussed and applied to an automotive Body-in-White component called dash. The dash is in the front area of the Body-in-White, between the left-hand-side shock-tower and the Cross Car Beam, and its task is to support the steering column. The dash under investigation is an asymmetric rib-web aluminium casting part. The influence of Additive Manufacturing constraints together with modal and stiffness targets is investigated in view of mass reduction. The constraints drive the topology result towards a feasible and fully self-supporting Additive Manufacturing solution. A simplified finite element model of the steering column and of the Body-in-White front area is presented, and the limiting assumption of isotropic material for Additive Manufacturing is discussed. The optimization problem is solved with a gradient-based method relying on the Solid Isotropic Material with Penalization and on the RAtional Material with Penalization algorithms, considering the overhang angle constraint with given build directions. Three metals are tested: steel, aluminium and magnesium alloys. Topology optimization results with and without overhang angle constraints are discussed and compared. The aluminium solution, preferred for its lesser weight, has been preliminarily redesigned following the optimization results. The new dash concept has been validated by finite element considering stiffness, modal responses, and buckling resistance targets. The proposed dash design weighs 721 g compared to the 1537 g of the reference dash, with a weight reduction of 53%, for the same structural targets.

Sign in / Sign up

Export Citation Format

Share Document