Investigation of vertical axis wind turbine airfoil performance in rain

2017 ◽  
Vol 232 (2) ◽  
pp. 181-194 ◽  
Author(s):  
Zhenlong Wu ◽  
Yihua Cao
Keyword(s):  
Wind Turbine ◽  
Wind Turbines ◽  
Meteorological Condition ◽  
Vertical Axis ◽  
Vertical Axis Wind Turbine ◽  
Vertical Axis Wind Turbines ◽  
Turbine Performance ◽  
Practical Design ◽  
Wind Turbine Airfoil ◽  
Naca 0015

Rainfall is a common meteorological condition that wind turbines may encounter and by which their performance may be affected. This paper comprehensively investigates the effects of rainfall on a NACA 0015 airfoil which is commonly used in vertical axis wind turbines. A CFD-based Eulerian–Lagrangian multiphase approach is proposed to study the static, rotating, and oscillating performances of the NACA 0015 airfoil in rainy conditions. It is found that for the different airfoil movements, the airfoil performance can seriously be deteriorated in the rain condition. Rain also causes premature boundary layer separations and more severe flow recirculations than in the dry condition. These findings seem to be the first open reports on rain effects on wind turbine performance and should be of some significance to practical design.

Investigation of Self-Starting Capability of Vertical Axis Wind Turbines Using a Computational Fluid Dynamics Approach

2011 ◽  
Vol 133 (4) ◽  
Author(s):  
Alexandrina Untaroiu ◽  
Houston G. Wood ◽  
Paul E. Allaire ◽  
Robert J. Ribando
Keyword(s):  
Fluid Dynamics ◽  
Computational Fluid Dynamics ◽  
Wind Turbine ◽  
Wind Turbines ◽  
Vertical Axis ◽  
Mesh Deformation ◽  
Operating Speed ◽  
Vertical Axis Wind Turbine ◽  
Vertical Axis Wind Turbines ◽  
Turbine Performance

Vertical axis wind turbines have always been a controversial technology; claims regarding their benefits and drawbacks have been debated since the initial patent in 1931. Despite this contention, very little systematic vertical axis wind turbine research has been accomplished. Experimental assessments remain prohibitively expensive, while analytical analyses are limited by the complexity of the system. Numerical methods can address both concerns, but inadequate computing power hampered this field. Instead, approximating models were developed which provided some basis for study; but all these exhibited high error margins when compared with actual turbine performance data and were only useful in some operating regimes. Modern computers are capable of more accurate computational fluid dynamics analysis, but most research has focused on horizontal axis configurations or modeling of single blades rather than full geometries. In order to address this research gap, a systematic review of vertical axis wind-power turbine (VAWT) was undertaken, starting with establishment of a methodology for vertical axis wind turbine simulation that is presented in this paper. Replicating the experimental prototype, both 2D and 3D models of a three-bladed vertical axis wind turbine were generated. Full transient computational fluid dynamics (CFD) simulations using mesh deformation capability available in ansys-CFX were run from turbine start-up to operating speed and compared with the experimental data in order to validate the technique. A circular inner domain, containing the blades and the rotor, was allowed to undergo mesh deformation with a rotational velocity that varied with torque generated by the incoming wind. Results have demonstrated that a transient CFD simulation using a two-dimensional computational model can accurately predict vertical axis wind turbine operating speed within 12% error, with the caveat that intermediate turbine performance is not accurately captured.

Vertical axis wind turbine operation in icing conditions: A review study

2021 ◽  
pp. 0309524X2110618
Author(s):  
Syed Abdur Rahman Tahir ◽  
Muhammad Shakeel Virk
Keyword(s):  
Wind Turbine ◽  
Wind Turbines ◽  
Vertical Axis ◽  
Electricity Production ◽  
Vertical Axis Wind Turbine ◽  
Vertical Axis Wind Turbines ◽  
Horizontal Axis Wind Turbines ◽  
Promising Solution ◽  
Review Study ◽  
Accretion Physics

Vertical Axis Wind Turbine (VAWT) can be a promising solution for electricity production in remote ice prone territories of high north, where good wind resources are available, but icing is a challenge that can affect its optimum operation. A lot of research has been made to study the icing effects on the conventional horizontal axis wind turbines, but the literature about vertical axis wind turbines operating in icing conditions is still scarce, despite the importance of this topic. This paper presents a review study about existing knowledge of VAWT operation in icing condition. Focus has been made in better understanding of ice accretion physics along VAWT blades and methods to detect and mitigate icing effects.

scholarly journals Aerodynamic improvement of Darrieus wind turbine

2021 ◽  
Vol 897 (1) ◽  
pp. 012001
Author(s):  
Oleg Goman ◽  
Andrii Dreus ◽  
Anton Rozhkevych ◽  
Krystyna Heti
Keyword(s):  
Reynolds Number ◽  
Wind Turbine ◽  
Wind Turbines ◽  
Structural Reliability ◽  
Vertical Axis ◽  
Vertical Wind ◽  
Integral Approach ◽  
Vertical Axis Wind Turbine ◽  
Calculation Algorithm ◽  
Vertical Axis Wind Turbines

Abstract Until recently, vertical-axis wind turbines are less extensively developed in wind energetics. At the same time, there are a number of advantages in turbines of such type like their independence from the change of wind direction, lower levels of aerodynamic and infrasound noises, higher structural reliability (compared to horizontal engines), etc. With these advantages, vertical-axis wind turbines demonstrate promising capacities. Inter alia, the productiveness of such turbines can be refined through the aerodynamic improvement of the structure and comprehensive optimization of the rotor geometry. The main purpose of the presented paper is to aerodynamically improve vertical wind turbine in order to increase the efficiency of wind energy conversion into electricity. Within the framework of the classical theory of impulses, this article presents a study of the effect of variation in Reynolds number on the general energy characteristics of a vertical-axis wind turbine with two blades. The integral approach makes it possible to use a single-disk impulse model to determine the main specific indicators of the system. The power factor was calculated based on the obtained value of the shaft torque factor, which in turn was determined by numerically integrating the total torque generated by the wind turbine. To calculate the test problem, we used the classic NACA airfoils: 0012, 0015, 0018 and 0021. The proposed calculation algorithm makes it possible not to indicate the Reynolds number and corresponding aerodynamic coefficients at the beginning of the calculation, but to recalculate it depending on the relative speed, position of the airfoil and the linear speed of the airfoil around the circumference. Proposed modern design techniques can be helpful for optimization of vertical wind turbines.

scholarly journals On mooring line tension and fatigue prediction for offshore vertical axis wind turbines: A comparison of lumped mass and quasi-static approaches

2018 ◽  
Vol 42 (2) ◽  
pp. 97-107 ◽  
Author(s):  
D Cevasco ◽  
M Collu ◽  
CM Rizzo ◽  
M Hall
Keyword(s):  
Wind Turbine ◽  
Wind Turbines ◽  
Line Tension ◽  
Vertical Axis ◽  
Offshore Wind ◽  
Mooring Line ◽  
Offshore Wind Turbine ◽  
Vertical Axis Wind Turbine ◽  
Lumped Mass ◽  
Vertical Axis Wind Turbines

Despite several potential advantages, relatively few studies and design support tools have been developed for floating vertical axis wind turbines. Due to the substantial aerodynamics differences, the analyses of vertical axis wind turbine on floating structures cannot be easily extended from what have been already done for horizontal axis wind turbines. Therefore, the main aim of the present work is to compare the dynamic response of the floating offshore wind turbine system adopting two different mooring dynamics approaches. Two versions of the in-house aero-hydro-mooring coupled model of dynamics for floating vertical axis wind turbine (FloVAWT) have been used, employing a mooring quasi-static model, which solves the equations using an energetic approach, and a modified version of floating vertical axis wind turbine, which instead couples with the lumped mass mooring line model MoorDyn. The results, in terms of mooring line tension, fatigue and response in frequency have been obtained and analysed, based on a 5 MW Darrieus type rotor supported by the OC4-DeepCwind semisubmersible.

scholarly journals An experimental study of the optimal design parameters of a wind power tower used to improve the performance of vertical axis wind turbines

2018 ◽  
Vol 10 (9) ◽  
pp. 168781401879954
Author(s):  
Soo-Yong Cho ◽  
Sang-Kyu Choi ◽  
Jin-Gyun Kim ◽  
Chong-Hyun Cho
Keyword(s):  
Experimental Study ◽  
Optimal Design ◽  
Wind Turbine ◽  
Wind Power ◽  
Wind Turbines ◽  
Vertical Axis ◽  
Power Coefficient ◽  
Design Parameters ◽  
Vertical Axis Wind Turbine ◽  
Vertical Axis Wind Turbines

In order to augment the performance of vertical axis wind turbines, wind power towers have been used because they increase the frontal area. Typically, the wind power tower is installed as a circular column around a vertical axis wind turbine because the vertical axis wind turbine should be operated in an omnidirectional wind. As a result, the performance of the vertical axis wind turbine depends on the design parameters of the wind power tower. An experimental study was conducted in a wind tunnel to investigate the optimal design parameters of the wind power tower. Three different sizes of guide walls were applied to test with various wind power tower design parameters. The tested vertical axis wind turbine consisted of three blades of the NACA0018 profile and its solidity was 0.5. In order to simulate the operation in omnidirectional winds, the wind power tower was fabricated to be rotated. The performance of the vertical axis wind turbine was severely varied depending on the azimuthal location of the wind power tower. Comparison of the performance of the vertical axis wind turbine was performed based on the power coefficient obtained by averaging for the one periodic azimuth angle. The optimal design parameters were estimated using the results obtained under equal experimental conditions. When the non-dimensional inner gap was 0.3, the performance of the vertical axis wind turbine was better than any other gaps.

Aerodynamic Measurements on a Vertical Axis Wind Turbine in a Large Scale Wind Tunnel

2010 ◽  
Author(s):  
L. Battisti ◽  
L. Zanne ◽  
S. Dell’Anna ◽  
V. Dossena ◽  
B. Paradiso ◽  
...  
Keyword(s):  
Wind Tunnel ◽  
Flow Field ◽  
Wind Turbine ◽  
Wind Turbines ◽  
Large Scale ◽  
Fluid Dynamic ◽  
Vertical Axis ◽  
Vertical Axis Wind Turbine ◽  
Aerodynamic Optimization ◽  
Vertical Axis Wind Turbines

This paper presents the first results of a wide experimental investigation on the aerodynamics of a vertical axis wind turbine. Vertical axis wind turbines have recently received particular attention, as interesting alternative for small and micro generation applications. However, the complex fluid dynamic mechanisms occurring in these machines make the aerodynamic optimization of the rotors still an open issue and detailed experimental analyses are now highly recommended to convert improved flow field comprehensions into novel design techniques. The experiments were performed in the large-scale wind tunnel of the Politecnico di Milano (Italy), where real-scale wind turbines for micro generation can be tested in full similarity conditions. Open and closed wind tunnel configurations are considered in such a way to quantify the influence of model blockage for several operational conditions. Integral torque and thrust measurements, as well as detailed aerodynamic measurements were applied to characterize the 3D flow field downstream of the turbine. The local unsteady flow field and the streamwise turbulent component, both resolved in phase with the rotor position, were derived by hot wire measurements. The paper critically analyses the models and the correlations usually applied to correct the wind tunnel blockage effects. Results evidence that the presently available theoretical correction models does not provide accurate estimates of the blockage effect in the case of vertical axis wind turbines. The tip aerodynamic phenomena, in particular, seem to play a key role for the prediction of the turbine performance; large-scale unsteadiness is observed in that region and a simple flow model is used to explain the different flow features with respect to horizontal axis wind turbines.

scholarly journals Fabrication and Performance Evaluation of Savonious Vertical Axis Wind Turbine for Uncertain Speed Regions

2017 ◽  
Vol 13 (2) ◽  
Keyword(s):  
Performance Evaluation ◽  
Wind Turbine ◽  
Wind Turbines ◽  
Urban Areas ◽  
Vertical Axis ◽  
Design Parameters ◽  
Vertical Axis Wind Turbine ◽  
Horizontal Axis Wind Turbine ◽  
Vertical Axis Wind Turbines ◽  
And Performance

The consumption of electricity in urban as well as rural is increasing every day and became an essential commodity for household and industrial purposes. Unfortunately the availability of electrical energy in India is not sufficient to the required demand and it is essential to discover and generate energy from non-conventional sources with cheap cost. On the same time it is necessary to reduce the consumption of conventional sources and to save fuel. Among all the renewable resources, wind is one of the best resources available all the time at free of cost. Especially vertical axis wind turbines (VAWT) are self-starting, omni directional. They require no yaw mechanism to continuously orient towards the wind direction and provide a more reliable energy conversion technology, as compared to horizontal axis wind turbine. Particularly savonius vertical axis wind turbines (SVAWT) are suitable and practically possible at low or uncertain wind speed regimes. They can be fitted on rooftops and also suitable for the urban areas where electricity is not available properly. This project deals with the fabrication and performance evaluation of savonius vertical axis wind turbine using two blade rotor. The amount of power developed by the wind turbine is calculated under theoretical and practical conditions and aerodynamics coefficients are also estimated. And various design parameters of savonious rotor are identified and determined.

scholarly journals Dynamic stall in vertical axis wind turbines: scaling and topological considerations

2018 ◽  
Vol 841 ◽  
pp. 746-766 ◽  
Author(s):  
Abel-John Buchner ◽  
Julio Soria ◽  
Damon Honnery ◽  
Alexander J. Smits
Keyword(s):  
Wind Turbine ◽  
Wind Turbines ◽  
Vortex Shedding ◽  
Turbine Blades ◽  
Vertical Axis ◽  
Dynamic Stall ◽  
Speed Ratio ◽  
Vertical Axis Wind Turbine ◽  
Wind Turbine Blades ◽  
Vertical Axis Wind Turbines

Vertical axis wind turbine blades are subject to rapid, cyclical variations in angle of attack and relative airspeed which can induce dynamic stall. This phenomenon poses an obstacle to the greater implementation of vertical axis wind turbines because dynamic stall can reduce turbine efficiency and induce structural vibrations and noise. This study seeks to provide a more comprehensive description of dynamic stall in vertical axis wind turbines, with an emphasis on understanding its parametric dependence and scaling behaviour. This problem is of practical relevance to vertical axis wind turbine design but the inherent coupling of the pitching and velocity scales in the blade kinematics makes this problem of more broad fundamental interest as well. Experiments are performed using particle image velocimetry in the vicinity of the blades of a straight-bladed gyromill-type vertical axis wind turbine at blade Reynolds numbers of between 50 000 and 140 000, tip speed ratios between $\unicode[STIX]{x1D706}=1$ to $\unicode[STIX]{x1D706}=5$, and dimensionless pitch rates of $0.10\leqslant K_{c}\leqslant 0.20$. The effect of these factors on the evolution, strength and timing of vortex shedding from the turbine blades is determined. It is found that tip speed ratio alone is insufficient to describe the circulation production and vortex shedding behaviour from vertical axis wind turbine blades, and a scaling incorporating the dimensionless pitch rate is proposed.

Iterative Approach in Design and Development of Vertical Axis Wind Turbines

2015 ◽  
Vol 792 ◽  
pp. 582-589 ◽  
Author(s):  
Evgeny Solomin ◽  
Irina Kirpichnikova ◽  
Andrey Martyanov
Keyword(s):  
Wind Turbine ◽  
Wind Turbines ◽  
Vertical Axis ◽  
Iterative Approach ◽  
Vertical Axis Wind Turbine ◽  
Design And Development ◽  
Step Method ◽  
Vertical Axis Wind Turbines ◽  
Scientific Approach ◽  
Method Of Design

Universal step-by-step method of design and development of multi-tier H-Darrieus Vertical-Axis Wind Turbine is described. The method is based on the systemic scientific approach of component-wise optimizing of the Turbine including the design of air foils, rotor outline configuration, alternator calculation and the development of power takeoff algorithm.

scholarly journals Wind Booster Optimization for On-Site Energy Generation Using Vertical-Axis Wind Turbines

Sensors ◽  
2021 ◽  
Vol 21 (14) ◽  
pp. 4775
Author(s):  
Marco A. Moreno-Armendáriz ◽  
Carlos A. Duchanoy ◽  
Hiram Calvo ◽  
Eddy Ibarra-Ontiveros ◽  
Jesua S. Salcedo-Castañeda ◽  
...  
Keyword(s):  
Wind Turbine ◽  
Wind Turbines ◽  
Energy Generation ◽  
Vertical Axis ◽  
Vertical Axis Wind Turbine ◽  
Large Cities ◽  
Wind Speeds ◽  
Vertical Axis Wind Turbines ◽  
Significant Area ◽  
Main Components

Large cities have a significant area of buildings with roofs that are not used most of the time. Vertical-axis wind turbines are suitable for this kind of on-site renewable energy generation. Since wind speeds are not high in these cities, a suitable solution to improve energy generation is to add a Wind Booster. This paper presents a methodology useful for selecting and optimizing the main components of a Wind Booster. As a case of study, we present this methodology in a Wind Booster for a Vertical Axis Wind Turbine (VAWT) that considers the wind flow’s specific behavior in a particular city. The final Wind Booster design is state of the art and makes use of Computational Fluid Dynamics (CFD) and Design of Experiments (DOE) techniques. We experimented with the conditions of Mexico City, obtaining a 35.23% increase in torque with the optimized Wind Booster configuration. The results obtained show the potential of this methodology to improve the performance of this kind of system. Moreover, since wind behavior is very different in each city, our proposal could be beneficial for researchers looking to implement the best possible wind turbine in their locality.

Sign in / Sign up

Export Citation Format

Share Document