scholarly journals Experimental and numerical investigations of tip clearance flow and loss in a variable geometry turbine cascade

2017 ◽  
Vol 232 (2) ◽  
pp. 157-169 ◽  
Author(s):  
Jie Gao ◽  
Weiliang Fu ◽  
Fukai Wang ◽  
Qun Zheng ◽  
Guoqiang Yue ◽  
...  
Keyword(s):  
Vortex Core ◽  
Three Dimensional ◽  
Tip Clearance ◽  
Leakage Flow ◽  
Variable Geometry ◽  
Numerical Predictions ◽  
Rear Part ◽  
Clearance Flow ◽  
Variable Geometry Turbine ◽  
Vane Tip

Variable geometry turbines are widely employed to improve the off-design performance of gas turbine engines; however, there is a performance penalty associated with the vane-end partial gap required for the movement of variable vanes. This paper is a continuation of the previous work and aims to understand the leakage flow and loss mechanisms under the influence of the pivoting axis. Experimental investigations with a variable geometry turbine linear cascade have been conducted for tip gap heights of 1.1% and 2.2% blade spans as well as setting angles of −6°, 0°, and 6°, so as to reveal the three-dimensional clearance flow characteristics associated with partial gaps. Besides, numerical predictions are also carried out to better understand the experimental results. Pressure measurements were performed on the tip endwall as well as on the vane surface, and three-dimensional clearance flow fields downstream of the variable cascade were measured with a five-hole probe. The results show that as the vane setting angle is changed from design to closed, the vane loading increases and tends to be more aft-loaded, thus increasing the tip leakage loss, and vice versa. There are strong interactions between the flow around the pivoting axis and the leakage flow in the vane tip rear part, which leads to a low-pressure region on the tip endwall. The leakage vortex core is made up of the leakage flow in the vane tip rear part at both two tip gap heights, and the leakage vortex core formation process is different from the one in the rotor blade. The present results can provide useful references for the vane-end clearance design of variable geometry turbines.

Physics of Tip Clearance Flow in Turbomachinery (Keynote Paper)

2002 ◽  
Author(s):  
Masahiro Inoue ◽  
Masato Furukawa
Keyword(s):  
Flow Field ◽  
Physical Interpretation ◽  
Vortex Core ◽  
Vortical Structure ◽  
Three Dimensional ◽  
Axial Flow ◽  
Tip Clearance ◽  
Tip Clearance Flow ◽  
Clearance Flow ◽  
Flow Phenomena

In a recent advanced aerodynamic design of turbomachinery, the physical interpretation of three-dimensional flow field obtained by a numerical simulation is important for iterative modifications of the blade or impeller geometry. This paper describes an approach to the physical interpretation of the tip clearance flow in turbomachinery. First, typical flow phenomena of the tip clearance flow are outlined for axial and radial compressors, pumps and turbines to help comprehensive understanding of the tip clearance flow. Then, a vortex-core identification method which enables to extract the vortical structure from the complicated flow field is introduced, since elucidation of the vortical structure is essential to the physical interpretation of the tip clearance flow. By use of the vortex-core identification, some interesting phenomena of the tip clearance flows are interpreted, especially focussing on axial flow compressors.

Tip Leakage Flow in Radial Inflow Rotor of a Microturbine With Varying Blade-Shroud Clearance

2007 ◽  
Author(s):  
Qinghua Deng ◽  
Jiufang Niu ◽  
Zhenping Feng
Keyword(s):  
Three Dimensional ◽  
Flow Simulation ◽  
Turbine Rotor ◽  
Tip Clearance ◽  
Transverse Mass ◽  
Leakage Flow ◽  
Tip Leakage Flow ◽  
Tip Clearance Flow ◽  
Tip Leakage ◽  
Clearance Flow

In this paper, tip clearance flow in a radial inflow turbine rotor under the stage environment is investigated using a three-dimensional viscous flow simulation with three different blade-shroud gap heights of 1%, 2% and 3% of the local span. The results indicate that more relative casing motion increases the scraping effect on tip leakage flow at the rotor entrance. Also, the scraping flow can dominate the whole tip clearance at the rotor entrance when the velocity is high enough at the rotor tip diameter. Regardless of the transverse mass flow rates of the three tip clearances, the results strongly exhibit the characteristics of linearity when the relative meridional length S is greater than 40%. According to the analysis of leakage flow fields in the tip clearance, measures such as a circumference slot, axial slot, or honeycomb are proposed to be applied and placed at the shroud surface over the exducer of the rotor for effectively reducing the transverse flow.

Interaction of Tip Clearance Flow and Three-Dimensional Separations in Axial Compressors

2006 ◽  
Author(s):  
Semiu A. Gbadebo ◽  
Nicholas A. Cumpsty ◽  
Tom P. Hynes
Keyword(s):  
Three Dimensional ◽  
Leading Edge ◽  
Horseshoe Vortex ◽  
Tip Clearance ◽  
Compressor Cascade ◽  
Suction Surface ◽  
Tip Clearance Flow ◽  
Separation Line ◽  
Numerical Predictions ◽  
Clearance Flow

This paper considers the interaction of tip clearance flow with three-dimensional (3D) separations in the corner region of a compressor cascade. Three-dimensional numerical computations were carried out using ten levels of tip clearance, ranging from zero to 2.18% of blade chord. The 3D separations on the blade suction surface were largely removed by the clearance flow for clearance about 0.58% of chord. For this cascade, experimental results at zero and 1.7% chord tip clearance were used to assess the validity of the numerical predictions. The removal mechanism was associated with the suppression of the leading edge horseshoe vortex and the interaction of tip clearance flow with the endwall boundary layer, which develops into a secondary flow as it is drifted towards the blade suction surface. Such interaction leads to the formation of a new 3D separation line on the endwall. The separation line forms the base of a separated stream surface which rolls up into the clearance vortex.

Effects of the Inlet Flow Conditions on the Tip Clearance Flow of an Isolated Compressor Rotor

2002 ◽  
Author(s):  
Holger Brandt ◽  
Leonhard Fottner ◽  
Horst Saathoff ◽  
Udo Stark
Keyword(s):  
Boundary Layer ◽  
Tip Clearance ◽  
Leakage Flow ◽  
Tip Leakage Flow ◽  
Inlet Flow ◽  
Tip Clearance Flow ◽  
Compressor Rotor ◽  
Numerical Predictions ◽  
Clearance Flow ◽  
Inflow Conditions

Numerical investigations on the effects of varying inflow conditions on the tip leakage flow field of an isolated low–speed compressor rotor and the respective rotor tip section cascade were performed at corresponding operation points. Inlet flow variations at each flow rate were obtained by means of varying the boundary layer thickness in such a manner that the non-dimensional integral parameters of the simulated inflow boundary layers were identical for the rotor and cascade. In order to describe the flowfield through the tip gap and its interactions with the incoming flow accurately, a fully–gridded tip gap region was employed. The numerical predictions for comparable inflow conditions agree well with experimental results from previous investigations on the endwall boundary layer separation due to tip clearance flow. It is demonstrated by the simulations that thickening the inflow boundary layer forces the roll-up point of the clearance vortex to move towards the leading edge. By its effects upon leakage flow, varying the incoming boundary layer has a deleterious effect on stall mass flow similar to increasing the tip clearance height. The investigations further reveal a great deal of similarity between the steady state clearance flow in the cascade and the rotor overtip leakage flow.

Interaction of Tip Clearance Flow and Three-Dimensional Separations in Axial Compressors

2006 ◽  
Vol 129 (4) ◽  
pp. 679-685 ◽  
Author(s):  
Semiu A. Gbadebo ◽  
Nicholas A. Cumpsty ◽  
Tom P. Hynes
Keyword(s):  
Three Dimensional ◽  
Leading Edge ◽  
Horseshoe Vortex ◽  
Tip Clearance ◽  
Compressor Cascade ◽  
Suction Surface ◽  
Tip Clearance Flow ◽  
Separation Line ◽  
Numerical Predictions ◽  
Clearance Flow

This paper considers the interaction of tip clearance flow with three-dimensional (3D) separations in the corner region of a compressor cascade. Three-dimensional numerical computations were carried out using ten levels of tip clearance, ranging from zero to 2.18% of blade chord. The 3D separations on the blade suction surface were largely removed by the clearance flow for clearance about 0.58% of chord. For this cascade, experimental results at zero and 1.7% chord tip clearance were used to assess the validity of the numerical predictions. The removal mechanism was associated with the suppression of the leading edge horseshoe vortex and the interaction of tip clearance flow with the endwall boundary layer, which develops into a secondary flow as it is driven towards the blade suction surface. Such interaction leads to the formation of a new 3D separation line on the endwall. The separation line forms the base of a separated stream surface which rolls up into the clearance vortex.

Effect of Upstream Unsteady Flow Conditions on Rotor Tip Leakage Flow

2002 ◽  
Author(s):  
Borislav T. Sirakov ◽  
Choon S. Tan
Keyword(s):  
Three Dimensional ◽  
Pressure Rise ◽  
Tip Clearance ◽  
High Loading ◽  
Causal Mechanism ◽  
Leakage Flow ◽  
Tip Leakage Flow ◽  
Tip Clearance Flow ◽  
Clearance Flow ◽  
The Impact

A study has been conducted, using unsteady three-dimensional Reynolds-averaged Navier-Stokes simulations to determine the impact on rotor performance of the interaction between the stator wakes and rotor tip clearance flow. The key effects of the interaction are: (1) a decrease in loss and blockage associated with tip clearance flow; (2) an increase in passage static pressure rise. Performance benefit is seen in the whole operability range of interest, from near design to high loading. The benefit is modest near design and increases with loading. Significant beneficial changes occur when the phenomenon of tip clearance flow double-leakage is present. Double-leakage occurs when the tip clearance flow passes through the tip gap of the neighboring blade. Double-leakage typically takes place at high loading but can be present at design condition, as well. A benefit due to unsteady interaction is also observed in the operability range of the rotor. A new generic causal mechanism is proposed to explain the observed changes in performance. It identifies the interaction between the tip clearance flow and the pressure pulses, induced on the rotor blade pressure surface by the upstream wakes, as the cause for the observed effects. The direct effect of the interaction is a decrease in the time-average double-leakage flow through the tip clearance gap so that the stream-wise defect of the exiting tip flow is lower with respect to the main flow. A lower defect leads to a decrease in loss and blockage generation and hence an enhanced performance compared to that in the steady situation. The performance benefits increase monotonically with loading and scale linearly with upstream wake velocity defect.

scholarly journals Numerical Calculation of Flow for Cascade With Tip Clearance

1994 ◽  
Author(s):  
Shimpei Mizuki ◽  
Hoshio Tsujita
Keyword(s):  
Three Dimensional ◽  
Tip Clearance ◽  
Turbine Cascade ◽  
Governing Equations ◽  
Tensor Form ◽  
Pressure Surface ◽  
Rear Part ◽  
Blade Tip ◽  
Flow Through ◽  
Blade Tip Geometry

Three-dimensional incompressible turbulent flow within a linear turbine cascade with tip clearance is analyzed numerically. The governing equations involving the standard k-ε model are solved in the physical component tensor form with a boundary-fitted coordinate system. In the analysis, the blade tip geometry is treated accurately in order to predict the flow through the tip clearance in detail when the blades have large thicknesses. Although the number of grids employed in the present study is not enough because of the limitation of computer storage memory, the computed results show good agreements with the experimental results. Moreover, the results clearly exhibit the locus of minimum pressure on the rear part of the pressure surface at the blade tip.

Numerical Simulation of Tip Clearance Control in Axial Turbine Rotor: Part 2—Passive Control of Five Different Tip Platforms

2008 ◽  
Author(s):  
Wei Li ◽  
Wei-Yang Qiao ◽  
Kai-Fu Xu ◽  
Hua-Ling Luo
Keyword(s):  
Flow Control ◽  
Passive Control ◽  
Suction Side ◽  
Turbine Rotor ◽  
Tip Clearance ◽  
Leakage Flow ◽  
Tip Leakage Flow ◽  
Tip Clearance Flow ◽  
Tip Leakage ◽  
Clearance Flow

The tip leakage flow has significant effects on turbine in loss production, aerodynamic efficiency, etc. Then it’s important to minimize these effects for a better performance by adopting corresponding flow control. The active turbine tip clearance flow control with injection from the tip platform is given in Part-1 of this paper. This paper is Part-2 of the two-part papers focusing on the effect of five different passive turbine tip clearance flow control methods on the tip clearance flow physics, which consists of a partial suction side squealer tip (Partial SS Squealer), a double squealer tip (Double Side Squealer), a pressure side tip shelf with inclined squealer tip on a double squealer tip (Improved PS Squealer), a tip platform extension edge in pressure side (PS Extension) and in suction side (SS Extension) respectively. Combined with the turbine rotor and the numerical method mentioned in Part 1, the effects of passive turbine tip clearance flow controls on the tip clearance flow were sequentially simulated. The detailed tip clearance flow fields with different squealer rims were described with the streamline and the velocity vector in various planes parallel to the tip platform or normal to the tip leakage vortex core. Accordingly, the mechanisms of five passive controls were put in evidence; the effects of the passive controls on the turbine efficiency and the tip clearance flow field were highlighted. The results show that the secondary flow loss near the outer casing including the tip leakage flow and the casing boundary layer can be reduced in all the five passive control methods. Comparing the active control with the passive control, the effect brought by the active injection control on the tip leakage flow is evident. The turbine rotor efficiency could be increased via the rational passive turbine tip clearance flow control. The Improved PS Squealer had the best effect on turbine rotor efficiency, and it increased by 0.215%.

Sign in / Sign up

Export Citation Format

Share Document