A nonlinear robust optimal controller for an active transfemoral prosthesis: An estimator-based state-dependent Riccati equation approach

Author(s):  
Anna Bavarsad ◽  
Ahmad Fakharian ◽  
Mohammad Bagher Menhaj

This article presents an estimator-based nonlinear robust optimal controller for an active prosthetic leg for transfemoral amputees. The proposed controller is derived from a combination of the state-dependent Riccati equation technique to optimize the energy consumption of the robot/prosthesis system and the sliding mode control to reduce the effects of the model parametric uncertainties and ground reaction forces as nonparametric uncertainties. In addition, the integral state control technique is employed to improve tracking; also, to have a compromise between tracking performance and control signal chattering, the boundary layer is then used. In this study, the performance of both the controller and estimator in the presence of noise and disturbance is assessed for nominal system while ±40% parametric uncertainty with respect to saturation bounds of control signals is considered. The results of the simulation in this research with ±40% parametric uncertainty compared to a robust adaptive impedance control approach with the only variation of ±30% on the system parameters, show high performance of the proposed controllers in reducing energy consumption, good robustness, improved position tracking performance, and good performance in estimating state variables, even in the presence of large initial errors compared to the extended Kalman filter.

Author(s):  
Eming Chen

Abstract In the flexible robot force control situations, if there exists a discontinuity between the robot tip sensor and the work-piece, the robot contact process becomes a nonlinear system control problem. The control tasks require the robot hand to switch from free motion control to contact motion control. The inevitable high impact force tends to let the system become unstable. The purpose of this paper is to investigate the control of the manipulator during this process. In this paper, dynamic models of the flexible link manipulator in both non-contacted and contacted modes are first derived. Due to the fact that the arm vibration shape functions are changed between the two modes, a transform matrix will be used to transform the controlled state variables, such as generalized position and velocity. A nonlinear sliding mode control technique has been implemented in an attempt to extinguish the chatter phenomenon and settle quickly to the desired setpoint.


Author(s):  
Siddharth Sridhar ◽  
Rumit Kumar ◽  
Kelly Cohen ◽  
Manish Kumar

Tilt-rotor quadcopters are a novel class of quadcopters with a servo motor attached on each arm that assist the quadcopter’s rotors to tilt to a desired angle thereby enabling thrust vectoring. Using these additional tilt angles, this type of a quadcopter can be used to achieve desired trajectories with faster maneuvering and can handle external disturbances better than a conventional quadcopter. In this paper, a non-linear controller has been designed using sliding mode technique for the pitch, roll, yaw motions and the servo motor tilt angles of the quadcopter. The dynamic model of the tilt-rotor quadcopter is presented, based on which sliding surfaces were designed to minimize the tracking errors. Using the control inputs derived from these sliding surfaces, the state variables converge to their desired values in finite-time. Further, the non-linear sliding surface coefficients are obtained by stability analysis. The robustness of this proposed sliding mode control technique is shown when a faulty motor scenario is introduced. The quadcopter transforms into a T-copter design upon motor failure thereby abetting the UAV to cope up with the instabilities experienced in yaw, pitch and roll axes and still completing the flight mission. The dynamics of the T-copter design and the derivation of the switching surface coefficients for this reconfigurable system are also presented.


2021 ◽  
Author(s):  
Weiqiu Pan ◽  
Tianzeng Li ◽  
Yu Wang

Abstract This paper deals with the issue of the multi-switching sliding mode combination synchronization (MSSMCS) of fractional order (FO) chaotic systems with different structures and unknown parameters under double stochastic disturbances (SD) utilizing the multi-switching synchronization method. The stochastic disturbances are considered as nonlinear uncertainties and external disturbances. Our theoretical part is divided into two cases, namely, the dimension of the drive-response system are different (or same). Firstly, a FO sliding surface was established in term of fractional calculus. Secondly, depended on the FO Lyapunov stability theory, the adaptive control technology and sliding mode control technique, the multi-switching adaptive controllers (MSAC) and some suitable multi-switching adaptive updating laws (MSAUL) are designed, so that the state variables of the drive systems are synchronized with the different state variables of the response systems. Simultaneously, the unknown parameters are assessed and the upper bound of stochastic disturbances are examined. Selecting the suitable scale matrices, the multi-switching projection synchronization, multi-switching complete synchronization, and multi-switching anti-synchronization will become special cases of MSSMCS. Finally, examples are displayed to certify the usefulness and validity of the demonstrated scheme via MATLAB.


Author(s):  
Osamu Ohnuki ◽  
Kenzo Nonami

Abstract In this paper, a method to realize the motion and vibration control without sensors is proposed. Sensorless control is generally realized by estimating the state of the system from the measured current in the actuator by means of an observer. It is possible to estimate all state variables because of dynamic interaction in the controlled object. Then we realize nonlinear robust control system based on the observer. In this paper, first we formulate sensorless control system. As controlled objects we deal with a multi-degree-of-freedom structure as a vibration control problem and a single link robot arm as a motion control problem, respectively, and we carry out numerical simulations. Moreover, we also verify the possibility of realization of sensorless control by experiments.


Sign in / Sign up

Export Citation Format

Share Document