Comparison of monolithic and composite piezoelectric material–based energy harvesting devices

2014 ◽  
Vol 25 (14) ◽  
pp. 1825-1837 ◽  
Author(s):  
Hyun J Song ◽  
Young-Tai Choi ◽  
Norman M Wereley ◽  
Ashish Purekar
Keyword(s):  
Energy Harvesting ◽  
Piezoelectric Material ◽  
Energy Harvesting Devices

scholarly journals Power Consideration in a Piezoelectric Generator

2013 ◽  
Vol 2013 ◽  
pp. 1-7
Author(s):  
Rémi Tardiveau ◽  
Frédéric Giraud ◽  
Adrian Amanci ◽  
Francis Dawson ◽  
Christophe Giraud-Audine ◽  
...  
Keyword(s):  
Phase Shift ◽  
Energy Harvesting ◽  
Resonant Frequency ◽  
Piezoelectric Material ◽  
Power Flow ◽  
Mechanical Energy ◽  
Power Losses ◽  
Vibration Excitation ◽  
Piezoelectric Generator ◽  
Energy Harvesting Devices

A piezoelectric generator converts mechanical energy into electricity and is used in energy harvesting devices. In this paper, synchronisation conditions in regard to the excitation vibration are studied. We show that a phase shift of ninety degrees between the vibration excitation and the bender’s displacement provides the maximum power from the mechanical excitation. However, the piezoelectric material is prone to power losses; hence the bender’s displacement amplitude is optimised in order to increase the amount of power which is converted into electricity. In the paper, we use active energy harvesting to control the power flow, and all the results are achieved at a frequency of 200 Hz which is well below the generator’s resonant frequency.

scholarly journals Preliminary Study of Optimum Piezoelectric Cross-Ply Composites for Energy Harvesting

2012 ◽  
Vol 2012 ◽  
pp. 1-8 ◽  
Author(s):  
David N. Betts ◽  
H. Alicia Kim ◽  
Christopher R. Bowen
Keyword(s):  
Energy Harvesting ◽  
Numerical Investigation ◽  
Piezoelectric Material ◽  
Electrical Energy ◽  
State Change ◽  
Power Extraction ◽  
Wide Range ◽  
Preliminary Study ◽  
Rectangular Laminate ◽  
Energy Harvesting Devices

Energy harvesting devices based on a piezoelectric material attached to asymmetric bistable laminate plates have been shown to exhibit high levels of power extraction over a wide range of frequencies. This paper optimizes for the design of bistable composites combined with piezoelectrics for energy harvesting applications. The electrical energy generated during state-change, or “snap-through,” is maximized through variation in ply thicknesses and rectangular laminate edge lengths. The design is constrained by a bistability constraint and limits on both the magnitude of deflection and the force required for the reversible actuation. Optimum solutions are obtained for differing numbers of plies and the numerical investigation results are discussed.

Vibrational Energy Harvesting Devices

2010 ◽  
Vol 2 (2) ◽  
pp. 80-92
Author(s):  
Rupesh Patel ◽  
Atanas A. Popov ◽  
Stewart McWilliam
Keyword(s):  
Energy Harvesting ◽  
Vibrational Energy ◽  
Energy Harvesting Devices ◽  
Vibrational Energy Harvesting

scholarly journals Piezoelectric property comparison of two-dimensional ZnO nanostructures for energy harvesting devices

RSC Advances ◽  
2021 ◽  
Vol 11 (6) ◽  
pp. 3363-3370
Author(s):  
Ang Yang ◽  
Yu Qiu ◽  
Dechao Yang ◽  
Kehong Lin ◽  
Shiying Guo
Keyword(s):  
Energy Harvesting ◽  
Piezoelectric Property ◽  
Piezoelectric Effect ◽  
Theoretical Studies ◽  
Two Dimensional ◽  
Zno Nanostructures ◽  
Energy Harvesting Devices ◽  
Experimental And Theoretical Studies

In this paper, experimental and theoretical studies of the piezoelectric effect of two-dimensional ZnO nanostructures, including straight nanosheets (SNSs) and curved nanosheets (CNSs) are conducted.

scholarly journals Enhanced Power Extraction with Sediment Microbial Fuel Cells by Anode Alternation

Fuels ◽  
2021 ◽  
Vol 2 (2) ◽  
pp. 168-178
Author(s):  
Marzia Quaglio ◽  
Daniyal Ahmed ◽  
Giulia Massaglia ◽  
Adriano Sacco ◽  
Valentina Margaria ◽  
...  
Keyword(s):  
Fuel Cells ◽  
Energy Harvesting ◽  
Power Density ◽  
Microbial Fuel Cells ◽  
Average Power ◽  
Power Extraction ◽  
Harvesting Technique ◽  
Harvesting Method ◽  
Energy Harvesting Devices ◽  
Efficient Power

Sediment microbial fuel cells (SMFCs) are energy harvesting devices where the anode is buried inside marine sediment, while the cathode stays in an aerobic environment on the surface of the water. To apply this SCMFC as a power source, it is crucial to have an efficient power management system, leading to development of an effective energy harvesting technique suitable for such biological devices. In this work, we demonstrate an effective method to improve power extraction with SMFCs based on anodes alternation. We have altered the setup of a traditional SMFC to include two anodes working with the same cathode. This setup is compared with a traditional setup (control) and a setup that undergoes intermittent energy harvesting, establishing the improvement of energy collection using the anodes alternation technique. Control SMFC produced an average power density of 6.3 mW/m2 and SMFC operating intermittently produced 8.1 mW/m2. On the other hand, SMFC operating using the anodes alternation technique produced an average power density of 23.5 mW/m2. These results indicate the utility of the proposed anodes alternation method over both the control and intermittent energy harvesting techniques. The Anode Alternation can also be viewed as an advancement of the intermittent energy harvesting method.

scholarly journals Power-Generation Optimization Based on Piezoelectric Ceramic Deformation for Energy Harvesting Application with Renewable Energy

Energies ◽  
2021 ◽  
Vol 14 (8) ◽  
pp. 2171
Author(s):  
Hyeonsu Han ◽  
Junghyuk Ko
Keyword(s):  
Power Generation ◽  
Renewable Energy ◽  
Energy Harvesting ◽  
Piezoelectric Material ◽  
Lead Zirconate Titanate ◽  
Piezoelectric Ceramic ◽  
Piezoelectric Element ◽  
Piezoelectric Ceramics ◽  
Lead Zirconate ◽  
Piezoelectric Energy

Along with the increase in renewable energy, research on energy harvesting combined with piezoelectric energy is being conducted. However, it is difficult to predict the power generation of combined harvesting because there is no data on the power generation by a single piezoelectric material. Before predicting the corresponding power generation and efficiency, it is necessary to quantify the power generation by a single piezoelectric material alone. In this study, the generated power is measured based on three parameters (size of the piezoelectric ceramic, depth of compression, and speed of compression) that contribute to the deformation of a single PZT (Lead zirconate titanate)-based piezoelectric element. The generated power was analyzed by comparing with the corresponding parameters. The analysis results are as follows: (i) considering the difference between the size of the piezoelectric ceramic and the generated power, 20 mm was the most efficient piezoelectric ceramic size, (ii) considering the case of piezoelectric ceramics sized 14 mm, the generated power continued to increase with the increase in the compression depth of the piezoelectric ceramic, and (iii) For piezoelectric ceramics of all diameters, the longer the depth of deformation, the shorter the frequency, and depending on the depth of deformation, there is a specific frequency at which the charging power is maximum. Based on the findings of this study, PZT-based elements can be applied to cases that receive indirect force, including vibration energy and wave energy. In addition, the power generation of a PZT-based element can be predicted, and efficient conditions can be set for maximum power generation.

scholarly journals Design and Analysis of a While-Drilling Energy-Harvesting Device Based on Piezoelectric Effect

Energies ◽  
2021 ◽  
Vol 14 (5) ◽  
pp. 1266
Author(s):  
Jun Zheng ◽  
Bin Dou ◽  
Zilong Li ◽  
Tianyu Wu ◽  
Hong Tian ◽  
...  
Keyword(s):  
Energy Harvesting ◽  
Piezoelectric Material ◽  
Longitudinal Vibration ◽  
Coupling Model ◽  
Energy Harvest ◽  
Peak Voltage ◽  
Piezoelectric Patch ◽  
Theoretical Support ◽  
Piezoelectric Coupling ◽  
Continuous Power

A while-drilling energy harvesting device is designed in this paper to recovery energy along with the longitudinal vibration of the drill pipes, aiming to serve as a continuous power supply for downhole instruments during the drilling procedure. Radial size of the energy harvesting device is determined through the drilling engineering field experience and geological survey reports. A piezoelectric coupling model based on the selected piezoelectric material was established via COMSOL Multiphysics numerical simulation. The forced vibration was analyzed to determine the piezoelectric patch length range and their best installation positions. Modal analysis and frequency response research indicate that the natural frequency of the piezoelectric cantilever beam increased monotonously with the increase of the piezoelectric patch’ thickness before reaching an inflection point. Moreover, the simulation results imply that the peak voltage of the harvested energy varied in a regional manner with the increase of the piezoelectric patches. When the thickness of the piezoelectric patches was 1.2–1.4 mm, the designed device gained the best energy harvest performance with a peak voltage of 15–40 V. Works in this paper provide theoretical support and design reference for the application of the piezoelectric material in the drilling field.

Sign in / Sign up

Export Citation Format

Share Document