scholarly journals Micro-scale numerical study of fiber/matrix debonding in steel fiber composites

2020 ◽  
Vol 15 ◽  
pp. 155892502091072 ◽  
Author(s):  
Baris Sabuncuoglu ◽  
Stepan V Lomov
Keyword(s):  
Steel Fiber ◽  
Volume Fraction ◽  
Numerical Study ◽  
Glass Fibers ◽  
Fiber Composites ◽  
Steel Fibers ◽  
Opening Angle ◽  
Stress Concentrations ◽  
Fiber Volume ◽  
Fiber Matrix

Fiber/matrix debonding behavior of steel fiber composites is analyzed using a parametric finite element modeling procedure and compared with conventional composites with carbon and glass fibers. Cohesive surfaces are applied to fiber–matrix interface to simulate the debonding behavior, while the interface strength properties of steel fiber are obtained with and without surface treatment. The effect of various parameters on the debonding behavior is investigated, including stress concentrations, fiber diameter, fiber shape, and fiber volume fraction, using the parametric model. The influence of stress concentrations is determined to be much lower than the debonding strength. Debonding damage is more evident in larger fibers compared to smaller ones. Earlier and sudden interface separation is observed with the polygonal steel fibers compared to the circular ones. Increase in the fiber volume ratio increases the debonding opening distance but does not affect the opening angle significantly. The results can be useful for assessing possibilities to use steel fibers to increase toughness of the composites in comparison with glass and carbon reinforcement.

Experimental Study on Effects of Steel Fiber Volume on Mechanical Properties of SFRC

2011 ◽  
Vol 214 ◽  
pp. 144-148 ◽  
Author(s):  
Farnoud Rahimi Mansour ◽  
Sasan Parniani ◽  
Izni Syahrizal Ibrahim
Keyword(s):  
Steel Fiber ◽  
Volume Fraction ◽  
Impact Resistance ◽  
Fiber Reinforced Concrete ◽  
Steel Fibers ◽  
Engineering Properties ◽  
Water Tank ◽  
Steel Fiber Reinforced Concrete ◽  
Fiber Volume ◽  
Modes Of Failure

In recent years, considerable interest has developed in using fibers to increase the load-carrying capacity of concrete members. Fibers significantly reduce the brittleness of concrete and improve its engineering properties, such as tensile, flexural, impact resistance, fatigue, load bearing capacity after cracking and toughness. However, studies on the exact amount of influence are very limited. Among fibers, steel fibers are one of the most popular and widely used types of fibers in both research and practice. Steel fiber-reinforced concrete (SFRC) has been used increasingly in recent years and has a lot of applications. Previous researchers have mentioned that using fiber as 0.5 – 2.5 % of the volume of concrete can significantly improve the concrete properties. The purpose of this paper is firstly to investigate the effects of fiber volume on the compressive, splitting, and flexural behaviors of SFRC, and secondly to compare modes of failure. Variable items are the steel fiber volume fraction and the curing day. A series of 108 specimens (cube, cylinder and prism) with four different steel fiber volumes are used by a ratio of 0, 0.7, 1.0 and 1.5%. All specimens are cured in a water tank for 7, 14 and 28 days, respectively to provide same conditions. Hooked-ended steel fibers with a length of 30mm and a diameter of 0.75 mm are used.

Study on Long-Term Expansive Deformation of Self-Stressing Concrete with Combined Restrictions of Steel Fibers and Steel Bar

2010 ◽  
Vol 452-453 ◽  
pp. 533-536 ◽  
Author(s):  
Huan An He ◽  
Wei Dong ◽  
Zhi Min Wu
Keyword(s):  
Prestressed Concrete ◽  
High Performance ◽  
Steel Fiber ◽  
High Performance Concrete ◽  
Volume Fraction ◽  
Steel Fibers ◽  
Fiber Reinforced ◽  
Fiber Volume ◽  
Expansive Concrete

Self-stressing concrete is sort of expansive concrete with high expansion energy which can induce prestresses with restriction in concrete, and steel fibers also enhance tensile strength of concrete. The combination of these two high performance concrete can be used to improve the cracking resistance of concrete significantly. However, like mechanical prestressed concrete, a stable long-term prestresses (self-stresses) level is a key to exploit the particular advantage of steel fiber reinforced self-stressing concrete. Self-stresses are created by restricting the expansion of self-stressing concrete with steel bars or/and steel fibers, therefore, in this paper a series of tests on long-term expansive deformation of concrete were carried out by means of measuring restrict expansive deformation of self-stressing concrete with restriction of steel fibers. The results of tests showed, based on the three-year recording, that the expansive deformation of steel fiber reinforced self-stressing concrete almost kept the same as that of 28-day without remarkable rebound which indicated that losses of self-stresses were not significant and can meet the design requirements on self-stresses level. In addition, it is proposed on the relationship between restrict expansive deformation and reinforcement ratio of steel rebars under different steel fiber volume fraction from 0-2%.

Research on Long-Term Expansive Deformation of Steel Fiber Reinforced Expansive Concrete

2009 ◽  
Vol 417-418 ◽  
pp. 945-948
Author(s):  
Huan An He ◽  
You Gang Wang
Keyword(s):  
High Performance ◽  
Steel Fiber ◽  
High Performance Concrete ◽  
Volume Fraction ◽  
Steel Fibers ◽  
Fiber Reinforced ◽  
Fiber Volume ◽  
Expansive Concrete ◽  
Steel Bar

The inherent low tensile strength and shrinkage result in cracking of concrete under work loads. A new way to improve cracking properties is distributing steel fibers into expansive concrete to form a type of composite which is called steel fiber reinforced expansive concrete. This type of high performance concrete could compensate shrinkage as well as improving crack strength. For this concrete, the key point to ensure high performance and safety of concrete structure is to keep a stable expansive deformation during long-term service. A series of tests were carried out to measure long-term restrained expansive deformations of steel fiber reinforced expansive concrete with ages under various restrictions like steel bars and steel fibers. The test investigated some 3-year specimens. For all specimens, test parameters included 2 ratios of steel bar reinforcement, 4 volume fractions of steel fiber and 4 dosages of expansion admixture. The test results showed that the expansion of concrete decreased with increasing of steel bar reinforcing ratio as well as steel fiber volume fraction. In addition, when being in a lower dosage of expansion admixture, the specimens presented remarkable retraction of the expansive deformation. However, when beyond a certain dosage of expansion admixture, the long-term expansive deformation had less change with ages and almost remained the same with 90-day deformation, namely less losses of deformation. Hence, for steel fiber reinforced expansive concrete, using an appropriate dosage of expansion admixture could meet the requirements of designed strengthening and compensating shrinkage.

scholarly journals Effects of Steel Fibers Geometry on the Mechanical Properties of SIFCON Concrete

2020 ◽  
Vol 6 (1) ◽  
pp. 21-33 ◽  
Author(s):  
Shahad S. Khamees ◽  
Mohammed M. Kadhum ◽  
Nameer A. Alwash
Keyword(s):  
Mechanical Properties ◽  
Steel Fiber ◽  
Volume Fraction ◽  
Fiber Reinforced Concrete ◽  
Steel Fibers ◽  
Partial Replacement ◽  
Fiber Volume ◽  
Fiber Network ◽  
Static Modulus ◽  
Static Modulus Of Elasticity

This research aims to shed light on the effect of steel fiber shape, length, diameter, and aspect ratio on the mechanical properties of slurry infiltration fiber reinforced concrete (SIFCON). This study comprised of casting and testing three groups of SIFCON specimens with 6% fiber volume fraction. The first group was reinforced with micro steel fiber, other reinforced by hook end steel fibers, while the last group of specimens reinforced by mixing two shape of steel fiber as hybrid fiber (3% micro steel fiber +3% hook end steel fiber). Silica fume was used as a partial replacement (10%) by weight of cement. 3.7% super plasticizer was used to make the slurry liquid enough to penetrate through the fiber network, while the w/c ratio kept constant at 0.33. It was found from the results achieved that the compressive strength, static modulus of elasticity, splitting tensile strength and toughness are extremely affected by the geometry of fibers because the network of fibers formed and their density depends on the size and shape of fibers. Where the values of micro steel fibers are far outweighing the values of hooked end fibers. It was also deduced from empiricism results that combining long and short fibers gives excellent results.

scholarly journals Experimental Evaluation of Effects of Steel and Glass Fibers on Engineering Properties of Concrete: Engineering Properties of Concrete

2020 ◽  
Vol 14 (54) ◽  
pp. 116-127
Author(s):  
Jalal Akbari ◽  
Amirhossein Abed
Keyword(s):  
Compressive Strength ◽  
Steel Fiber ◽  
Volume Fraction ◽  
Glass Fibers ◽  
Plain Concrete ◽  
Steel Fibers ◽  
Engineering Properties ◽  
Concrete Mixtures ◽  
Strength Tests ◽  
Cylindrical Samples

This paper experimentally investigates the effect of steel and glass fibers on the engineering properties of concrete. To achieve this, 0.3%, 0.6%, and 0.9% by volume fraction of steel and glass fibers are added in concrete mixtures with water-to-cement (W/C) ratios 0.35 and 0.45. For each ratio of water to cement, 21 cubic samples for compressive strength tests, 14 cylindrical samples for tension strength tests, and also 14 prismatic samples for three-point flexural strength tests were prepared. The experimental results show that adding 0.3% to 0.9% % steel fibers for concrete increases simultaneously the compressive, tension, and also flexural strengths in comparison with plain concrete. Adding glass fibers only between 0.3% to 0.6% increases the compressive strength. The results reveal that the best range for reinforcing concrete with steel fiber is 0.3% to 0.9 % and glass fiber is 0.3% to 0.6 % by volume fraction of fiber to improve the engineering strengths concrete. As a rule of thumb, the tension and flexural strengths of concrete could be explained as 8% and 13% of the compressive strength, respectively.

scholarly journals Experimental Study on Shear Performance of Cast-In-Place Ultra-High Performance Concrete Structures

Materials ◽  
2019 ◽  
Vol 12 (19) ◽  
pp. 3254 ◽  
Author(s):  
Li ◽  
Feng ◽  
Ke ◽  
Pan ◽  
Nie
Keyword(s):  
Shear Strength ◽  
High Performance ◽  
Fiber Volume Fraction ◽  
Steel Fiber ◽  
High Performance Concrete ◽  
Volume Fraction ◽  
Steel Fibers ◽  
Direct Shear ◽  
Ultra High Performance Concrete ◽  
Fiber Volume

In order to study the direct shear properties of ultra-high performance concrete (UHPC) structures, 15 Z-shaped monolithic placement specimens (MPSs) and 12 Z-shaped waterjet treated specimens (WJTSs) were tested to study the shear behavior and failure modes. The effects of steel fiber shape, steel fiber volume fraction and interface treatment on the direct shear properties of UHPC were investigated. The test results demonstrate that the MPSs were reinforced with steel fibers and underwent ductile failure. The ultimate load of the MPS is about 166.9% of the initial cracking load. However, the WJTSs failed in a typical brittle mode. Increasing the fiber volume fraction significantly improves the shear strength, which can reach 24.72 MPa. The steel fiber type has little effect on the shear strength and ductility, while increasing the length of steel fibers improves its ductility and slightly reduces the shear strength. The direct shear strength of the WJTSs made from 16 mm hooked-type steel fibers can reach 9.15 MPa, which is 2.47 times the direct shear strength of the specimens without fibers. Finally, an interaction formula for the shear and compressive strength was proposed on the basis of the experimental results, to predict the shear load-carrying capacity of the cast-in-place UHPC structures.

Micro-scale finite element analysis of stress concentrations in steel fiber composites under transverse loading

2014 ◽  
Vol 49 (9) ◽  
pp. 1057-1069 ◽  
Author(s):  
Baris Sabuncuoglu ◽  
Svetlana Orlova ◽  
Larissa Gorbatikh ◽  
Stepan V Lomov ◽  
Ignaas Verpoest
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Steel Fiber ◽  
Fiber Composites ◽  
Transverse Loading ◽  
Stress Concentrations ◽  
Element Analysis ◽  
Micro Scale

scholarly journals Shrinkage and Mechanical Properties of Self-Compacting SFRC With Calcium-Sulfoaluminate Expansive Agent

Materials ◽  
2020 ◽  
Vol 13 (3) ◽  
pp. 588 ◽  
Author(s):  
Changyong Li ◽  
Pengran Shang ◽  
Fenglan Li ◽  
Meng Feng ◽  
Shunbo Zhao
Keyword(s):  
Mechanical Properties ◽  
Steel Fiber ◽  
Volume Fraction ◽  
Cementitious Materials ◽  
Fiber Reinforced Concrete ◽  
Steel Fibers ◽  
Steel Fiber Reinforced Concrete ◽  
Volume Stability ◽  
Calcium Sulfoaluminate ◽  
Expansive Agent

With the premise of ensuring workability on a fresh mixture, the volume stability of hardened self-compacting steel fiber reinforced concrete (SFRC) becomes an issue due to the content of cementitious materials increased with the volume fraction of steel fiber. By using the expansive agent to reduce the shrinkage deformation of self-compacting SFRC, the strength reduction of hardened self-compacting SFRC is another issue. To solve these issues, this paper performed an experimental investigation on the workability, shrinkage, and mechanical properties of self-compacting SFRC compared to the self-compacting concrete (SCC) with or without an expansive agent. The calcium-sulfoaluminate expansive agent with content optimized to be 10% mass of binders and the steel fiber with a varying volume fraction from 0.4% to 1.2% were selected as the main parameters. The mix proportion of self-compacting SFRC with expansive agent was designed by the direct absolute volume method, of which the steel fibers are considered to be the distributed coarse aggregates. Results showed that rational high filling and passing ability of fresh self-compacting SFRC was ensured by increasing the binder to coarse-aggregate ratio and the sand ratio in the mix proportions; the autogenous and drying shrinkages of hardened self-compacting SFRC reduced by 22.2% to 3.2% and by 18.5% to 7.3% compared to those of the SCC without expansive agent at a curing age of 180 d, although the expansion effect of expansive agent decreased with the increasing volume fraction of steel fiber; the mechanical properties, including the compressive strength, the splitting tensile strength, and the modulus of elasticity increased with the incorporation of an expansive agent and steel fibers, which met the design requirements.

scholarly journals Using Steel Fiber-Reinforced Concrete Precast Panels for Strengthening in Shear of Beams: An Experimental and Analytical Investigation

2019 ◽  
Vol 2019 ◽  
pp. 1-18 ◽  
Author(s):  
Pitcha Jongvivatsakul ◽  
Linh V. H. Bui ◽  
Theethawachr Koyekaewphring ◽  
Atichon Kunawisarut ◽  
Narawit Hemstapat ◽  
...  
Keyword(s):  
Reinforced Concrete ◽  
Steel Fiber ◽  
Volume Fraction ◽  
Fiber Reinforced Concrete ◽  
Experimental Program ◽  
Rc Beams ◽  
Fiber Reinforced ◽  
Steel Fiber Reinforced Concrete ◽  
Fiber Volume ◽  
Simple Formulation

In this paper, the performances of reinforced concrete (RC) beams strengthened in shear with steel fiber-reinforced concrete (SFRC) panels are investigated through experiment, analytical computation, and numerical analysis. An experimental program of RC beams strengthened by using SFRC panels, which were attached to both sides of the beams, is carried out to investigate the effects of fiber volume fraction, connection type, and number and diameter of bolts on the structural responses of the retrofitted beams. The current shear resisting model is also employed to discuss the test data considering shear contribution of SFRC panels. The experimental results indicate that the shear effectiveness of the beams strengthened by using SFRC panels is significantly improved. A three-dimensional (3D) nonlinear finite element (FE) analysis adopting ABAQUS is also conducted to simulate the beams strengthened in shear with SFRC panels. The investigation reveals the good agreement between the experimental and analytical results in terms of the mechanical behaviors. To complement the analytical study, a parametric study is performed to further evaluate the influences of panel thickness, compressive strength of SFRC, and bolt pattern on the performances of the beams. Based on the numerical and experimental analysis, a shear resisting model incorporating the simple formulation of average tensile strength perpendicular to the diagonal crack of the strengthened SFRC panels is proposed with the acceptable accuracy for predicting the shear contribution of the SFRC system under various effects.

Sign in / Sign up

Export Citation Format

Share Document