Enhanced wear resistance of cast ductile iron by Ni-SiC composite coating

2005 ◽  
Vol 18 (5) ◽  
pp. 315-320 ◽  
Author(s):  
Khaled M. Ibrahim ◽  
A. Abdel Aal ◽  
Z. Abdel Hamid
Keyword(s):  
Wear Resistance ◽  
Composite Coating ◽  
Ductile Iron ◽  
Cast Ductile Iron

Investigation of thermochemical boriding effect on wear behavior of a GGG 50 quality as-cast ductile iron

2016 ◽  
Vol 68 (4) ◽  
pp. 476-481 ◽  
Author(s):  
Harun Mindivan
Keyword(s):  
Wear Resistance ◽  
Abrasive Wear ◽  
Ductile Iron ◽  
Room Temperature ◽  
Wear Behavior ◽  
Surface Hardness ◽  
Wear Test ◽  
Content Type ◽  
Pin On Disc ◽  
Cast Ductile Iron

Purpose This study aims to investigate the microstructure and the abrasive wear features of the untreated and pack borided GGG 50 quality ductile iron under various working temperatures. Design/methodology/approach GGG 50 quality as-cast ductile iron samples were pack borided in Ekabor II powder at 900°C for 3 h, followed by furnace cooling. Structural characterization was made by optical microscopy. Mechanical characterization was made by hardness and pin-on-disc wear test. Pin-on-disc test was conducted on a 240-mesh Al2O3 abrasive paper at various temperatures in between 25 and 450°C. Findings Room temperature abrasive wear resistance of the borided ductile iron increased with an increase in its surface hardness. High-temperature abrasive wear resistances of the borided ductile iron linearly decreased with an increase in test temperature. However, the untreated ductile iron exhibited relatively high resistance to abrasion at a temperature of 150°C. Originality/value This study can be a practical reference and offers insight into the effects of boriding process on the increase of room temperature wear resistance. However, above 150°C, the untreated ductile iron exhibited similar abrasive wear performance as compared to the borided ductile iron.

DURA-BAR 80-55-06

Alloy Digest ◽  
2020 ◽  
Vol 69 (7) ◽  
Keyword(s):  
Wear Resistance ◽  
Shear Strength ◽  
Physical Properties ◽  
Tensile Properties ◽  
Surface Finish ◽  
Ductile Iron ◽  
Heat Treating ◽  
Continuous Cast ◽  
Cast Products

Abstract Dura-Bar 80-55-06 is a ferritic-pearlitic ductile iron that is used for continuous cast products. It offers higher strength and wear resistance when compared to Dura-Bar 65-45-12, while still possessing good machinability and surface finish. This datasheet provides information on composition, physical properties, hardness, elasticity, tensile properties, and shear strength. It also includes information on heat treating and machining. Filing Code: CI-71. Producer or source: Charter Dura-Bar, Inc.

Cast Ductile Iron 155mm M804 Bodies

1990 ◽  
Author(s):  
Charles Casad ◽  
Ivery Chambliss ◽  
William Thomas ◽  
Bill Twomey
Keyword(s):  
Ductile Iron ◽  
Cast Ductile Iron

scholarly journals A superior strength and sliding-wear resistance combination of ductile iron with nanobainitic matrix

2021 ◽  
Vol 11 ◽  
pp. 1175-1183
Author(s):  
Yuzhou Du ◽  
Xiaolong Wang ◽  
Dongya Zhang ◽  
Xin Wang ◽  
Chunpeng Ju ◽  
...  
Keyword(s):  
Wear Resistance ◽  
Ductile Iron ◽  
Sliding Wear

MICROSTRUCTURES AND DRY SLIDING WEAR RESISTANCE OF THE LASER CERAMICS COMPOSITE COATING ON PURE Ti

2012 ◽  
Vol 19 (03) ◽  
pp. 1250017 ◽  
Author(s):  
PENG LIU ◽  
YUANBIN ZHANG ◽  
HUI LUO ◽  
YUSHUANG HUO
Keyword(s):  
Wear Resistance ◽  
Composite Coating ◽  
Laser Cladding ◽  
Dry Sliding Wear ◽  
X Ray Diffraction ◽  
Phase Constituent ◽  
Fine Grain ◽  
Fine Grain Strengthening ◽  
Modification Technique ◽  
Surface Performance

In this study, Al–Ti–Co was used to improve the surface performance of pure Ti . Laser cladding is an important surface modification technique, which can be used to improve the surface performance of pure Ti . Laser cladding of the Al–Ti–Co + TiB2 pre-placed powders on pure Ti can form ceramics reinforced the composite coating, which improved the wear resistance of the substrate. Characteristics of the composite coating were investigated using X-ray diffraction (XRD), scanning electron microscopy (SEM), microhardness and wear tests. And the laser-cladded coating can also have major dilution from the substrate. Due to the action of the fine grain strengthening and the phase constituent, the wear resistance and microhardness of pure Ti surface were greatly improved.

Microstructural characteristics of SiC-B4C reinforced laser alloying composite coatings

2013 ◽  
Vol 20 (4) ◽  
pp. 307-310
Author(s):  
Li Wei
Keyword(s):  
Wear Resistance ◽  
Composite Coating ◽  
Fine Particles ◽  
Composite Coatings ◽  
Substrate Surface ◽  
Laser Alloying ◽  
Wear Process ◽  
High Microhardness ◽  
Deep Plowing ◽  
Coating Matrix

AbstractA hard SiC-B4C reinforced composite coating was fabricated by laser alloying of SiC-B4C+Al-Sn-Mo-Y2O3 mixed powders on a Ti-3Al-2V alloy. Al-Sn-Mo mixed powders were first used in the laser alloying technique to improve the wear resistance of titanium alloys. Proper selection of the laser alloying process parameters allows us to obtain a composite coating with a metallurgical combination with substrate. Under the action of Mo, fine particles with high microhardness were produced in the coating matrix and also hindered the formation of adhesion patches and deep plowing grooves during the sliding wear process, leading to the improvement of wear resistance of a titanium alloy substrate surface.

Sign in / Sign up

Export Citation Format

Share Document