scholarly journals Effects of Vibration Characteristics on the Atomization Performance in the Medical Piezoelectric Atomization Device Induced by Intra-Hole Fluctuation

2021 ◽  
Vol 34 (1) ◽  
Author(s):  
Qiufeng Yan ◽  
Wanting Sun ◽  
Lei Zhang ◽  
Hongmei Wang ◽  
Jianhui Zhang
Keyword(s):  
Mathematical Expression ◽  
Topical Administration ◽  
Vibration Characteristics ◽  
Mode Shapes ◽  
Inhalation Therapy ◽  
Laser Vibrometer ◽  
Micro Pump ◽  
Fluctuation Phenomenon ◽  
Oral Inhalation ◽  
Atomization Performance

AbstractOral inhalation of aerosolized drugs has be widely applied in healing the affected body organs including lesions of the throat and lungs and it is more efficient than those conventional therapies, such as intravenous drip, intramuscular injection and external topical administration in the aspects of the dosage reduction and side effects of drugs. Nevertheless, the traditional atomization devices always exhibit many drawbacks. For example, non-uniformed atomization particle distribution, the instability of transient atomization quantity and difficulties in precise energy control would seriously restrict an extensive use of atomization inhalation therapy. In this study, the principle of intra-hole fluctuation phenomenon occurred in the hole is fully explained, and the produced volume change is also estimated. Additionally, the mathematical expression of the atomization rate of the atomizing device is well established. The mechanism of the micro-pump is further clarified, and the influence of the vibration characteristics of the atomizing film on the atomization behavior is analyzed theoretically. The curves of sweep frequency against the velocity and amplitude of the piezoelectric vibrator are obtained by the Doppler laser vibrometer, and the corresponding mode shapes of the resonance point are achieved. The influence of vibration characteristics on atomization rate, atomization height and atomization particle size are also verified by experiments, respectively. Both the experimental results and theoretical calculation are expected to provide a guidance for the design of this kind of atomization device in the future.

Vibration-based delamination evaluation in GFRP composite beams using ANN

2021 ◽  
pp. 096739112110033
Author(s):  
TG Sreekanth ◽  
M Senthilkumar ◽  
S Manikanta Reddy
Keyword(s):  
Finite Element ◽  
Natural Frequency ◽  
Composite Structures ◽  
Composite Beams ◽  
Vibration Characteristics ◽  
Mode Shapes ◽  
Aviation Industry ◽  
Frequency Data ◽  
Fiber Reinforced ◽  
Back Propagation Algorithm

Delamination is definitely an important topic in the area of composite structures as it progressively worsens the mechanical performance of fiber-reinforced polymer composite structures in its service period. The detection and severity analysis of delaminations in engineering areas like the aviation industry is vital for safety and economic considerations. The existence of delaminations varies the vibration characteristics such as natural frequencies, mode shapes, etc. of composites and hence this indication can be effectively used for locating and quantifying the delaminations. The changes in vibration characteristics are considered as inputs for the inverse problem to determine the location and size of delaminations. In this paper Artificial Neural Network (ANN) is used for delamination evaluationof glass fiber-reinforced composite beams using natural frequency as typical vibration parameter. The Finite Element Analysis is used for generating the required dataset for ANN. The frequency-based delamination prediction technique is validated by finite element models and experimental modal analysis. The results indicate that the ANN-based back propagation algorithm can predict the location and size of delaminations in composites with good accuracy for numerical natural frequency data but the accuracy is comparitivelyless for experimental natural frequency data.

scholarly journals Vibrational Analysis on Hemp and Okra Fibres Mixed Glass Fiber Polyester Composite

2021 ◽  
Vol 8 (11) ◽  
pp. 55-62
Author(s):  
Putti Venkata Siva Teja ◽  
Badatala Ooha ◽  
Kondeti Sravanth
Keyword(s):  
Glass Fiber ◽  
Natural Frequency ◽  
Natural Frequencies ◽  
Fiber Composite ◽  
Fem Analysis ◽  
Vibration Characteristics ◽  
Mode Shapes ◽  
Machine Component ◽  
Free System ◽  
Glass Fiber Composite

In transverse vibrations the element moves to and fro in a direction perpendicular to the direction of the advance of the wave. To determine the vibration characteristics i.e., natural frequencies and mode shapes, modal analysis is a process for a structure or a machine component while is being designed. In real life, aero planes, missiles, rockets, space vehicles, satellites, sub marines etc are modeled as free-free mechanical systems. In this paper an attempt was made to compare natural frequency for two composite materials- ladies finger with Glass fiber composite and Hemp with Glass fiber composite by taking as cantilever beams. The cantilever beam which is fixed at one end is vibrated to obtain the natural frequency, mode shapes at four different modes. A simple low cost demonstration experiment is performed in this paper by using common apparatus in order to compare theoretical, numerical (FEM analysis) profiles of two free-free thin two rectangular composite beams of dimensions 305*49.5* 7 in mm. Keywords: Natural frequencies, Mode shapes, Vibration characteristics, Ladies finger fiber, Hemp fiber, Glass fiber, FEM analysis, Free-Free system.

Free vibration characteristics of delaminated composite pretwisted stiffened cylindrical shell

2017 ◽  
Vol 232 (4) ◽  
pp. 595-611 ◽  
Author(s):  
Mrutyunjay Rout ◽  
Sasank Shekhara Hota ◽  
Amit Karmakar
Keyword(s):  
Free Vibration ◽  
Dynamic Equilibrium ◽  
Twist Angle ◽  
Cylindrical Shells ◽  
Shell Element ◽  
Vibration Characteristics ◽  
Mode Shapes ◽  
Iteration Algorithm ◽  
Lagrange’S Equation ◽  
Benchmark Solutions

Effects of delamination on free vibration characteristics of laminated stiffened cylindrical shells with pretwist are analyzed by finite element method. The investigation is carried out using an eight-noded quadratic isoparametric shell element, which incorporates the transverse shear deformation and rotary inertia along with a three-noded beam element for the stiffener. The multipoint constraint algorithm has been included to guarantee the compatibility of deformation, equilibrium of resultant forces, and moments at delamination crack tip. The general dynamic equilibrium equation is derived from Lagrange’s equation of motion for moderate rotational speeds for which the Coriolis effect is neglected. The standard eigenvalue problem is solved utilizing QR iteration algorithm. The accuracy of the present formulation is validated with benchmark solutions is available in the literature. The present work concerns about the effects of delamination, fiber orientation, twist angle, stiffener depth-to-shell thickness ratio, and rotational speed on the fundamental frequency of shallow cylindrical shells with stiffener. Representative mode shapes for some typical case of the stiffened shell for different twist angles and rotational speeds are also presented.

Nonlinear Combination Resonances in Cantilever Composite Plates

1995 ◽  
Author(s):  
Kyoyul Oh ◽  
Ali H. Nayfeh
Keyword(s):  
Natural Frequencies ◽  
Excitation Frequency ◽  
Power Spectra ◽  
Low Frequency ◽  
Composite Plates ◽  
High Amplitude ◽  
Mode Shapes ◽  
Laser Vibrometer ◽  
Combination Resonance ◽  
Response Curves

Abstract We experimentally investigated nonlinear combination resonances in a graphite-epoxy cantilever plate having the configuration (–75/75/75/ – 75/75/ – 75)s. As a first step, we compared the natural frequencies and mode shapes obtained from the finite-element and experimental modal analyses. The largest difference in the obtained frequencies was 2.6%. Then, we transversely excited the plate and obtained force-response and frequency-response curves, which were used to characterize the plate dynamics. We acquired time-domain data for specific input conditions using an A/D card and used them to generate time traces, power spectra, pseudo-state portraits, and Poincaré maps. The data were obtained with an accelerometer monitoring the excitation and a laser vibrometer monitoring the plate response. We observed the external combination resonance Ω≈12(ω2+ω5) and the internal combination resonance Ω≈ω8≈12(ω2+ω13), where the ωi are the natural frequencies of the plate and Ω is the excitation frequency. The results show that a low-amplitude high-frequency excitation can produce a high-amplitude low-frequency motion.

scholarly journals Experimental and Numerical Investigation of Resonance Characteristics of Novel Pumping Element Driven by Two Piezoelectric Bimorphs

2019 ◽  
Vol 9 (6) ◽  
pp. 1234 ◽  
Author(s):  
Yu-Chih Lin ◽  
Yu-Hsi Huang ◽  
Kwen-Wei Chu
Keyword(s):  
Speckle Pattern ◽  
Laser Doppler Vibrometer ◽  
Impedance Analysis ◽  
Vibration Characteristics ◽  
Mode Shapes ◽  
Electronic Speckle Pattern Interferometry ◽  
Element Analysis ◽  
Visible Displacement ◽  
Piezoelectric Bimorphs ◽  
Phase Motion

This paper describes the vibration characteristics of a dual-bimorph piezoelectric pumping element under fluid–structure coupling. Unlike the single bimorph used in most previous studies, the proposed device comprises two piezoelectric bimorphs within an acrylic housing. Amplitude-fluctuation electronic speckle pattern interferometry (AF-ESPI) was used to examine the visible displacement fringes in order to elucidate the anti-phase as well as in-phase motions associated with vibration. Analysis was also conducted using impedance analysis and laser Doppler vibrometer (LDV) based on the measurement of point-wise displacement. The experimental results of resonant frequencies and the corresponding mode shapes are in good agreement with those obtained using finite element analysis. The gain of flow rate obtained by the anti-phase motion of the dual-bimorph pumping element is larger than both those obtained by in-phase motion and the single bimorph pumping element. This work greatly enhances our understanding of the vibration characteristics of piezoelectric pumping elements with two bimorphs, and provides a valuable reference for the further development of bionic pump designs.

The Application of Electrode Design in Vibrating Piezoceramic Plate for Energy Harvesting System

2013 ◽  
Author(s):  
Yu-Hsi Huang ◽  
Ching-Kong Chao ◽  
Wan-Ting Chou
Keyword(s):  
Energy Harvesting ◽  
Dynamic Characteristics ◽  
Electromechanical Coupling ◽  
Coupling Efficiency ◽  
Vibration Characteristics ◽  
Mode Shapes ◽  
Experimental Measurements ◽  
Piezoceramic Plate ◽  
Resonant Frequencies ◽  
Energy Harvesting System

The energy harvesting system of piezoceramic plate is studied on the electrode configuration to improve the electromechanical transferring efficiency. The piezoceramic plate is used to perform the vibration characteristics by experimental measurements and finite element method (FEM). Thereafter, the dynamic characteristics and the electromechanical coupling efficiency of the piezoelectric energy harvesting system are studied by the electrode design method of the piezoceramic plate. Several experimental techniques are used to measure the dynamic characteristics of piezoceramic plate. First, the full-filed optical technique, amplitude-fluctuation electronic speckle pattern interferometry (AF-ESPI), can measure simultaneously the resonant frequencies and mode shapes for out-of-plane and in-plane vibrations. Second, the pointwisely measuring system, laser Doppler vibrometer (LDV), can obtain resonant frequencies by dynamic signal swept-sine analysis. Third, the correspondent in-plane resonant frequencies and anti-resonant frequencies are obtained by impedance analysis. The experimental results of vibration characteristics are verified with numerical calculations. Besides the dynamic characteristics of piezoceramic plates are analyzed in converse piezoelectric effect, the direct piezoelectric effect of piezoceramic plates are excited by shaker to generate the electric voltage. It has excellent consistence between resonant frequencies and mode shapes on the vibration characteristics by experimental measurements and finite element numerical calculations. In this study, the Electrical Potential Gradient (EPG) calculated by FEM is proposed to evaluate the electromechanical coupling efficiency of piezoceramic plate on the specific vibration mode. The correspondent electrode configuration, which is designed by EPG, can produce the best electromechanical transfer both in direct and converse piezoelectric effects. It is concluded that the vibration characteristics of piezoelectric materials have excellent consistence determined by experimental measurements and FEM.

scholarly journals Wave Based Method for Free Vibration Analysis of Ring Stiffened Cylindrical Shell with Intermediate Large Frame Ribs

2013 ◽  
Vol 20 (3) ◽  
pp. 459-479 ◽  
Author(s):  
Meixia Chen ◽  
Jianhui Wei ◽  
Kun Xie ◽  
Naiqi Deng ◽  
Guoxiang Hou
Keyword(s):  
Cylindrical Shell ◽  
Free Vibration ◽  
Boundary Conditions ◽  
Natural Frequencies ◽  
Free Vibration Analysis ◽  
Structure Type ◽  
Vibration Characteristics ◽  
Mode Shapes ◽  
Arbitrary Boundary ◽  
Stiffened Cylindrical Shell

Wave based method which can be recognized as a semi-analytical and semi-numerical method is presented to analyze the free vibration characteristics of ring stiffened cylindrical shell with intermediate large frame ribs for arbitrary boundary conditions. According to the structure type and the positions of discontinuities, the model is divided into different substructures whose vibration field is expanded by wave functions which are exactly analytical solutions to the governing equations of the motions of corresponding structure type. Boundary conditions and continuity equations between different substructures are used to form the final matrix to be solved. Natural frequencies and vibration mode shapes are calculated by wave based method and the results show good agreement with finite element method for clamped-clamped, shear diaphragm – shear diaphragm and free-free boundary conditions. Free vibration characteristics of ring stiffened cylindrical shells with intermediate large frame ribs are compared with those with bulkheads and those with all ordinary ribs. Effects of the size, the number and the distribution of intermediate large frame rib are investigated. The frame rib which is large enough is playing a role as bulkhead, which can be considered imposing simply supported and clamped constraints at one end of the cabin and dividing the cylindrical shell into several cabins vibrating separately at their own natural frequencies.

Free Vibration Characteristics of Sandwich Conical Shells With FGM Face Sheets: A Finite Element Approach

2019 ◽  
Author(s):  
Tripuresh Deb Singha ◽  
Apurba Das ◽  
Gopal Agarwal ◽  
Tanmoy Bandyopadhyay ◽  
Amit Karmakar
Keyword(s):  
Finite Element Method ◽  
Finite Element ◽  
Free Vibration ◽  
Conical Shell ◽  
Vibration Characteristics ◽  
Mode Shapes ◽  
Iteration Algorithm ◽  
Operational Life ◽  
Sandwich Type ◽  
Element Method

Abstract This paper presents an analytical investigation on the free vibration characteristics of symmetric sandwich conical shell with functionally graded material (FGM) face sheets using finite element method. Sandwich-type structures offer higher stiffness to weight ratio with excellent thermal barrier in high temperature application extending the operational life of the component. The sandwich-type conical structure used in the advanced supersonic and hypersonic space vehicles. The material properties of FGM face sheets are considered to be varied in thickness direction as per simple power law distribution in terms of the volume fractions of the FGM constituents. The core layer is considered as homogeneous and made of an isotropic material (Titanium alloy-Ti–6Al–4V). A finite element method is used to reduce the governing equations of vibration problem. The QR iteration algorithm used to solve the standard eigen value problem for determine the natural frequencies. Convergence studies are performed in respect of mesh sizes to substantiate the accuracy of the proposed method. Computer codes developed to obtain the numerical results for the combined effects of twist angle and rotational speed on the free vibration characteristics of symmetric sandwich conical shell with FGM face sheets. A detailed numerical study is carried out to examine the influence of the sandwich plate type, volume fraction index on the free vibration characteristics. The typical mode shapes are also illustrated for different cases.

Effect of a Circumferential Arc Crack on the Vibration Characteristics of a Flexible Spinning Disk

2007 ◽  
Author(s):  
Nikhit N. Nair ◽  
Hamid N. Hashemi ◽  
Grant M. Warner
Keyword(s):  
Crack Opening ◽  
Equations Of Motion ◽  
Crack Depth ◽  
Bending Moment ◽  
Rotating Disk ◽  
Vibration Characteristics ◽  
Coupled Systems ◽  
Mode Shapes ◽  
Critical Speeds ◽  
Crack Location

The vibration characteristics of a circumferentially cracked rotating disk are investigated. The disk is assumed to be axisymmetric, flexible and clamped at the center. The crack increases the local flexibility of the disk at the crack location and is modeled as linear and torsional springs, connecting the two segments of the disk. The spring constants are evaluated by considering crack opening displacements due to bending moment and shear force at the crack location. The equations of motion of two segments of the disk, for disk operating in vacuum as well as subjected to shear fluid flow are developed. Using the Finite Difference Technique, the coupled systems of equations are solved and the natural frequencies and mode shapes are obtained. The mode shapes are seen to be comparatively flattened in the inner region of the disk separated by the crack and heightened towards the periphery of the disk. Shear fluid loading reduces the critical speeds and results in a quicker onset of instability. The degree of instability caused by the crack is a function of crack depth and location. Critical speeds increase with increasing crack distance from the central clamp and decrease with increasing crack depth.

Vibration Response of Functionally Graded Rotating Disk With a Circumferential Crack

2010 ◽  
Author(s):  
Rui Liu ◽  
Hamid Nayeb-Hashemi
Keyword(s):  
Critical Speed ◽  
Crack Depth ◽  
Rotating Disk ◽  
Vibration Characteristics ◽  
Functionally Graded ◽  
Mode Shapes ◽  
Campbell Diagram ◽  
Circumferential Crack ◽  
Inner Radius ◽  
The Galerkin Method

In this study, the vibration characteristics of a functionally graded rotating hollow disk with the circumferential surface crack are investigated. In order to simplify the problem, the circumferential crack of the rotating hollow disk is modeled as circumferential step indentation. The Galerkin Method is used to obtain the radial and hoop stresses for disks with clamped edge at the inner radius. Finite Difference scheme is adopted to solve the partial differential equation of motion of the rotating hollow disk to obtain the mode shapes and the Campbell Diagram. The first critical speed, which is one of the important parameters limiting the performance of the rotating disk, was obtained from the Campbell Diagram. The results show that the crack will reduce the stiffness and the critical speed of the rotating disk. Critical speed increases with decreasing the distance from inner radius to the crack and decreases with increasing crack depth. Furthermore, considering the functionally graded disk, the distribution of elastic modulus does not change significantly the effects of circumferential cracks on the vibration characteristics of the rotating.

Sign in / Sign up

Export Citation Format

Share Document