Amplitude balancing in separating P- and S-waves in 2D and 3D elastic seismic data

Geophysics ◽  
2011 ◽  
Vol 76 (3) ◽  
pp. S103-S113 ◽  
Author(s):  
Robert Sun ◽  
George A. McMechan ◽  
Han-Hsiang Chuang
Keyword(s):  
Wave Amplitude ◽  
Amplitude Ratio ◽  
Velocity Ratio ◽  
Displacement Component ◽  
P Wave ◽  
Elastic Displacement ◽  
Reverse Time ◽  
S Wave ◽  
Near Surface ◽  
S Waves

The reflected P- and S-waves in elastic displacement component data recorded at the earth’s surface are separated by reverse-time (downward) extrapolation of the data in an elastic computational model, followed by calculations to give divergence (dilatation) and curl (rotation) at a selected reference depth. The surface data are then reconstructed by separate forward-time (upward) scalar extrapolations, from the reference depth, of the magnitude of the divergence and curl wavefields, and extraction of the separated P- and S-waves, respectively, at the top of the models. A P-wave amplitude will change by a factor that is inversely proportional to the P-velocity when it is transformed from displacement to divergence, and an S-wave amplitude will change by a factor that is inversely proportional to the S-velocity when it is transformed from displacement to curl. Consequently, the ratio of the P- to the S-wave amplitude (the P-S amplitude ratio) in the form of divergence and curl (postseparation) is different from that in the (preseparation) displacement form. This distortion can be eliminated by multiplying the separated S-wave (curl) by a relative balancing factor (which is the S- to P-velocity ratio); thus, the postseparation P-S amplitude ratio can be returned to that in the preseparation data. The absolute P- and S-wave amplitudes are also recoverable by multiplying them by a factor that depends on frequency, on the P-velocity α, and on the unit of α and is location-dependent if the near-surface P-velocity is not constant.

Scalar reverse‐time depth migration of prestack elastic seismic data

Geophysics ◽  
2001 ◽  
Vol 66 (5) ◽  
pp. 1519-1527 ◽  
Author(s):  
Robert Sun ◽  
George A. McMechan
Keyword(s):  
Seismic Waves ◽  
Velocity Model ◽  
P Wave ◽  
Common Source ◽  
Reverse Time ◽  
S Wave ◽  
Wave Source ◽  
Reflected Waves ◽  
S Waves ◽  
Elastic Data

Reflected P‐to‐P and P‐to‐S converted seismic waves in a two‐component elastic common‐source gather generated with a P‐wave source in a two‐dimensional model can be imaged by two independent scalar reverse‐time depth migrations. The inputs to migration are pure P‐ and S‐waves that are extracted by divergence and curl calculations during (shallow) extrapolation of the elastic data recorded at the earth’s surface. For both P‐to‐P and P‐to‐S converted reflected waves, the imaging time at each point is the P‐wave traveltime from the source to that point. The extracted P‐wave is reverse‐time extrapolated and imaged with a P‐velocity model, using a finite difference solution of the scalar wave equation. The extracted S‐wave is reverse‐time extrapolated and imaged similarly, but with an S‐velocity model. Converted S‐wave data requires a polarity correction prior to migration to ensure constructive interference between data from adjacent sources. Synthetic examples show that the algorithm gives satisfactory results for laterally inhomogeneous models.

Velocity anisotropy in shale determined from crosshole seismic and vertical seismic profile data

Geophysics ◽  
1990 ◽  
Vol 55 (4) ◽  
pp. 470-479 ◽  
Author(s):  
D. F. Winterstein ◽  
B. N. P. Paulsson
Keyword(s):  
Seismic Profile ◽  
P Wave ◽  
Isotropic Model ◽  
S Wave ◽  
Vertical Seismic Profile ◽  
Near Surface ◽  
S Waves ◽  
Velocity Anisotropy ◽  
Wave Velocities ◽  
Late Tertiary

Crosshole and vertical seismic profile (VST) data made possible accurate characterization of the elastic properties, including noticeable velocity anisotropy, of a near‐surface late Tertiary shale formation. Shear‐wave splitting was obvious in both crosshole and VSP data. In crosshole data, two orthologonally polarrized shear (S) waves arrived 19 ms in the uppermost 246 ft (75 m). Vertically traveling S waves of the VSP separated about 10 ms in the uppermost 300 ft (90 m) but remained at nearly constant separation below that level. A transversely isotropic model, which incorporates a rapid increase in S-wave velocities with depth but slow increase in P-wave velocities, closely fits the data over most of the measured interval. Elastic constants of the transvesely isotropic model show spherical P- and [Formula: see text]wave velocity surfaces but an ellipsoidal [Formula: see text]wave surface with a ratio of major to minor axes of 1.15. The magnitude of this S-wave anisotropy is consistent with and lends credence to S-wave anisotropy magnitudes deduced less directly from data of many sedimentary basins.

Reflection and refraction of elastic waves at a corrugated interface

1966 ◽  
Vol 56 (1) ◽  
pp. 201-221
Author(s):  
Shuzo Asano
Keyword(s):  
Wave Amplitude ◽  
Normal Incidence ◽  
P Wave ◽  
Irregular Waves ◽  
Angle Of Incidence ◽  
S Wave ◽  
Reflected Waves ◽  
S Waves ◽  
Significant Difference ◽  
Almost All

abstract The effect of a corrugated interface on wave propagation is considered by using the method that was first applied to acoustical gratings by Rayleigh. The problem is what happens when a plane P wave is incident on a corrugated interface that separates two semi-infinite media. As is well known, there are irregular (scattered) waves as well as regular waves. By assuming both the amplitude and the slope of a corrugated interface to be small, quantities of the order of the square of corrugation amplitude are taken into account. In the case of normal incidence for three models considered, the effect of corrugation on reflection is larger than the effect of corrugation on refraction; the amplitude of the regularly reflected waves decreases, and that of the regularly refracted waves and of the irregular waves increases, as the corrugation amplitude becomes larger. Generally, the larger the velocity contrast, the larger the variation of wave amplitude with the wavelength and the amplitude of corrugation. The S wave component generally becomes larger as the wavelength of corrugation becomes smaller. Boundary waves exist, depending upon the ratio of wavelength of corrugation to that of the incident wave. For a specified interface, it is possible that there is a significant difference in wave amplitude as a function of the elastic constants. In the case of oblique incidence, computation was carried out for angles of incidence smaller than 15° for one model. For these small angles of incidence, almost all results for the case of normal incidence still hold. Furthermore, it can be concluded that the effect of the angle of incidence on reflected S waves is larger than for the other waves and that large differences in the amplitudes of waves at different angles of incidence may be expected for the irregular waves.

Prestack scalar reverse-time depth migration of 3D elastic seismic data

Geophysics ◽  
2006 ◽  
Vol 71 (5) ◽  
pp. S199-S207 ◽  
Author(s):  
Robert Sun ◽  
George A. McMechan ◽  
Chen-Shao Lee ◽  
Jinder Chow ◽  
Chen-Hong Chen
Keyword(s):  
Wave Equation ◽  
Finite Difference ◽  
Seismic Data ◽  
P Wave ◽  
Scalar Wave ◽  
Reverse Time ◽  
S Wave ◽  
Absolute Value ◽  
S Waves ◽  
Finite Difference Solution

Using two independent, 3D scalar reverse-time depth migrations, we migrate the reflected P- and S-waves in a prestack 3D, three-component (3-C), elastic seismic data volume generated with a P-wave source in a 3D model and recorded at the top of the model. Reflected P- and S-waves are extracted by divergence (a scalar) and curl (a 3-C vector) calculations, respectively, during shallow downward extrapolation of the elastic seismic data. The imaging time for the migrations of both the reflected P- and P-S converted waves at each point is the one-way P-wave traveltime from the source to that point.The divergence (the extracted P-waves) is reverse-time extrapolated using a finite-difference solution of the 3D scalar wave equation in a 3D P-velocity modeland is imaged to obtain the migrated P-image. The curl (the extracted S-waves) is first converted into a scalar S-wavefield by taking the curl’s absolute value as the absolute value of the scalar S-wavefield and assigning a positive sign if the curl is counterclockwise relative to the source or a negative sign otherwise. This scalar S-wavefield is then reverse-time extrapolated using a finite-difference solution of the 3D scalar wave equation in a 3D S-velocity model, and it is imaged with the same one-way P-wave traveltime imaging condition as that used for the P-wave. This achieves S-wave polarity uniformity and ensures constructive S-wave interference between data from adjacent sources. The algorithm gives satisfactory results on synthetic examples for 3D laterally inhomogeneous models.

Seismic vertical transversely isotropic parameter inversion from P- and S-wave cross-borehole measurements in an aquifer environment

Geophysics ◽  
2019 ◽  
Vol 84 (3) ◽  
pp. D101-D116
Author(s):  
Julius K. von Ketelhodt ◽  
Musa S. D. Manzi ◽  
Raymond J. Durrheim ◽  
Thomas Fechner
Keyword(s):  
Transversely Isotropic ◽  
P Wave ◽  
Perturbation Equation ◽  
S Wave ◽  
P Waves ◽  
Data Set ◽  
Near Surface ◽  
S Waves ◽  
Wave Measurements ◽  
Wave Splitting

Joint P- and S-wave measurements for tomographic cross-borehole analysis can offer more reliable interpretational insight concerning lithologic and geotechnical parameter variations compared with P-wave measurements on their own. However, anisotropy can have a large influence on S-wave measurements, with the S-wave splitting into two modes. We have developed an inversion for parameters of transversely isotropic with a vertical symmetry axis (VTI) media. Our inversion is based on the traveltime perturbation equation, using cross-gradient constraints to ensure structural similarity for the resulting VTI parameters. We first determine the inversion on a synthetic data set consisting of P-waves and vertically and horizontally polarized S-waves. Subsequently, we evaluate inversion results for a data set comprising jointly measured P-waves and vertically and horizontally polarized S-waves that were acquired in a near-surface ([Formula: see text]) aquifer environment (the Safira research site, Germany). The inverted models indicate that the anisotropy parameters [Formula: see text] and [Formula: see text] are close to zero, with no P-wave anisotropy present. A high [Formula: see text] ratio of up to nine causes considerable SV-wave anisotropy despite the low magnitudes for [Formula: see text] and [Formula: see text]. The SH-wave anisotropy parameter [Formula: see text] is estimated to be between 0.05 and 0.15 in the clay and lignite seams. The S-wave splitting is confirmed by polarization analysis prior to the inversion. The results suggest that S-wave anisotropy may be more severe than P-wave anisotropy in near-surface environments and should be taken into account when interpreting cross-borehole S-wave data.

Separation and enhancement of split S‐waves on multicomponent shot records from the BIRPS WISPA experiment

Geophysics ◽  
1994 ◽  
Vol 59 (1) ◽  
pp. 131-139 ◽  
Author(s):  
M. Boulfoul ◽  
D. R. Watts
Keyword(s):  
Synthetic Data ◽  
P Wave ◽  
Moving Window ◽  
Wave Analysis ◽  
S Wave ◽  
Near Surface ◽  
S Waves ◽  
Wave Velocities ◽  
Wave Splitting ◽  
Explosive Source

Instantaneous rotations are combined with f-k filtering to extract coherent S‐wave events from multicomponent shot records recorded by British Institutions Reflection Profiling Syndicate (BIRPS) Weardale Integrated S‐wave and P‐wave analysis (WISPA) experiment. This experiment was an attempt to measure the Poisson’s ratio of the lower crest by measuring P‐wave and S‐wave velocities. The multihole explosive source technique did generate S‐waves although not of opposite polarization. Attempts to produce stacks of the S‐wave data are unsuccessful because S‐wave splitting in the near surface produced random polarizations from receiver group to receiver group. The delay between the split wavelets varies but is commonly between 20 to 40 ms for 10 Hz wavelets. Dix hyperbola are produced on shot records after instantaneous rotations are followed by f-k filtering. To extract the instantaneous polarization, the traces are shifted back by the length of a moving window over which the calculation is performed. The instantaneous polarization direction is computed from the shifted data using the maximum eigenvector of the covariance matrix over the computation window. Split S‐waves are separated by the instantaneous rotation of the unshifted traces to the directions of the maximum eigenvectors determined for each position of the moving window. F-K filtering is required because of the presence of mode converted S‐waves and S‐waves produced by the explosive source near the time of detonation. Examples from synthetic data show that the method of instantaneous rotations will completely separate split S‐waves if the length of the moving window over which the calculation is performed is the length of the combined split wavelets. Separation may be achieved on synthetic data for wavelet delays as small as two sample intervals.

A wavefield-separation-based elastic least-squares reverse time migration

Geophysics ◽  
2018 ◽  
Vol 83 (3) ◽  
pp. S279-S297 ◽  
Author(s):  
Bingluo Gu ◽  
Zhenchun Li ◽  
Jianguang Han
Keyword(s):  
Least Squares ◽  
Synthetic Data ◽  
P Wave ◽  
Reverse Time ◽  
Reverse Time Migration ◽  
S Wave ◽  
S Waves ◽  
Numerical Tests ◽  
Time Migration

Elastic least-squares reverse time migration (ELSRTM) has the potential to provide improved subsurface reflectivity estimation. Compared with elastic RTM (ERTM), ELSRTM can produce images with higher spatial resolution, more balanced amplitudes, and fewer artifacts. However, the crosstalk between P- and S-waves can significantly degrade the imaging quality of ELSRTM. We have developed an ELSRTM method to suppress the crosstalk artifacts. This method includes three crucial points. The first is that the forward and backward wavefields are extrapolated based on the separated elastic velocity-stress equation of P- and S-waves. The second is that the separated vector P- and S-wave residuals are migrated to form reflectivity images of Lamé constants [Formula: see text] and [Formula: see text] independently. The third is that the reflectivity images of [Formula: see text] and [Formula: see text] are obtained by the vector P-wave wavefields achieved in the backward extrapolation of the separated vector P-wave residuals and the vector S-wave wavefields achieved in the backward extrapolation of the separated vector S-wave residuals, respectively. Numerical tests with synthetic data demonstrate that our ELSRTM method can produce images free of crosstalk artifacts. Compared with ELSRTM based on the coupled wavefields, our ELSRTM method has better convergence and higher accuracy.

A simple method for resolving large converted‐wave (P-SV) statics

Geophysics ◽  
1993 ◽  
Vol 58 (3) ◽  
pp. 429-433 ◽  
Author(s):  
Peter W. Cary ◽  
David W. S. Eaton
Keyword(s):  
P Wave ◽  
S Wave ◽  
Converted Wave ◽  
P Waves ◽  
Simple Method ◽  
Near Surface ◽  
S Waves ◽  
Static Solutions ◽  
Surface Fluctuations

The processing of converted‐wave (P-SV) seismic data requires certain special considerations, such as commonconversion‐point (CCP) binning techniques (Tessmer and Behle, 1988) and a modified normal moveout formula (Slotboom, 1990), that makes it different for processing conventional P-P data. However, from the processor’s perspective, the most problematic step is often the determination of residual S‐wave statics, which are commonly two to ten times greater than the P‐wave statics for the same location (Tatham and McCormack, 1991). Conventional residualstatics algorithms often produce numerous cycle skips when attempting to resolve very large statics. Unlike P‐waves, the velocity of S‐waves is virtually unaffected by near‐surface fluctuations in the water table (Figure 1). Hence, the P‐wave and S‐wave static solutions are largely unrelated to each other, so it is generally not feasible to approximate the S‐wave statics by simply scaling the known P‐wave static values (Anno, 1986).

Characterization of naturally fractured Arbuckle Group in the Wellington Field, Kansas, using S-wave amplitude variation with offset

2017 ◽  
Vol 5 (1) ◽  
pp. T49-T63 ◽  
Author(s):  
Menal Gupta ◽  
Kyle Spikes ◽  
Bob Hardage
Keyword(s):  
Wave Amplitude ◽  
Anisotropy Parameter ◽  
P Wave ◽  
Fracture Density ◽  
S Wave ◽  
Amplitude Variation ◽  
Fracture Characterization ◽  
Amplitude Variation With Offset ◽  
S Waves ◽  
Arbuckle Group

S-wave amplitude variation with offset (AVO) analysis is sensitive to the presence of fractures and can provide a high-resolution seismic-based fracture characterization as compared with traditionally used traveltime-based methods. To determine viable attributes for estimation of properties such as spatial density and fluid fill of fractures, S-wave AVO modeling and analysis is carried out in the Wellington Field, Kansas, where 9C-2D seismic data have been acquired. Analysis is performed on the Ordovician fractured-carbonate interval called the Arbuckle Group, which is being considered for [Formula: see text] sequestration. AVO modeling of the Arbuckle interval indicates that differences in AVO intercepts of different S-wave polarizations can estimate S-wave anisotropy parameter [Formula: see text], which gives an estimate of fracture density. In addition, modeling suggests that AVO gradients of [Formula: see text] and [Formula: see text] waves can be used to derive a seismic attribute to discriminate fluid fill in fractures, provided good-quality S-wave gathers are available. The intercept anisotropy (IA) attribute obtained from AVO intercepts of S-waves provides fracture density estimates within the Arbuckle Group. These estimates are consistent with the field-wide, low-frequency observations from seismic velocities and spatially limited, high-frequency estimates obtained from drill cores and sonic and borehole-image logs. The IA attribute highlights possible high-permeability zones in the Upper and Lower Arbuckle suitable for [Formula: see text] injection. The Middle Arbuckle indicates low fracture density, potentially acting as a baffle to vertical flow and providing a seal for the Lower Arbuckle. The gradient anisotropy attribute obtained from the AVO gradient of S-waves suggests that most fractures in the Arbuckle are brine saturated. This attribute has a potential application in monitoring the movement of a [Formula: see text] plume in the Arbuckle Group when time-lapse data become available. These results demonstrate that S-wave AVO attributes can supplement the P-wave derived subsurface properties and significantly reduce uncertainties in subsurface fracture characterization.

scholarly journals Array data processing techniques applied to long-period shear waves at Fennoscandian seismograph stations

1969 ◽  
Vol 59 (5) ◽  
pp. 1863-1887
Author(s):  
James H. Whitcomb
Keyword(s):  
Data Processing ◽  
Velocity Ratio ◽  
Underground Explosion ◽  
High Signal ◽  
S Wave ◽  
Array Data ◽  
S Waves ◽  
Long Period ◽  
Normal Record ◽  
The Individual

abstract Array data processing is applied to long-period records of S waves at a network of five Fennoscandian seismograph stations (Uppsala, Umeå, Nurmijärvi, Kongsberg, Copenhagen) with a maximum separation of 1300 km. Records of five earthquakes and one underground explosion are included in the study. The S motion is resolved into SH and SV, and after appropriate time shifts the individual traces are summed, both directly and after weighting. In general, high signal correlation exists among the different stations involved resulting in more accurate time readings, especially for records which have amplitudes that are too small to be read normally. S-wave station residuals correlate with the general crustal type under each station. In addition, the Fennoscandian shield may have a higher SH/SV velocity ratio than the adjacent tectonic area to the northwest.SV-to-P conversion at the base of the crust can seriously interfere with picking the onset of Sin normal record reading. The study demonstrates that, for epicentral distances beyond about 30°, existing networks of seismograph stations can be successfully used for array processing of long-period arrivals, especially the S arrivals.

Sign in / Sign up

Export Citation Format

Share Document