High-resolution acoustic impedance inversion to characterize turbidites at Marlim Field, Campos Basin, Brazil

2014 ◽  
Vol 2 (3) ◽  
pp. T143-T153 ◽  
Author(s):  
Tatiane M. Nascimento ◽  
Paulo T. L. Menezes ◽  
Igor L. Braga
Keyword(s):  
High Resolution ◽  
Seismic Data ◽  
Acoustic Impedance ◽  
Structural Information ◽  
Low Frequency ◽  
Seismic Inversion ◽  
Background Model ◽  
Rock Properties ◽  
High Porosity ◽  
Campos Basin

Seismic inversion is routinely used to determine rock properties, such as acoustic impedance and porosity, from seismic data. Nonuniqueness of the solutions is a major issue. A good strategy to reduce this inherent ambiguity of the inversion procedure is to introduce stratigraphic and structural information a priori to better construct the low-frequency background model. This is particularly relevant when studying heterogeneous deepwater turbidite reservoirs that form prolific, but complex, hydrocarbon plays in the Brazilian offshore basins. We evaluated a high-resolution inversion workflow applied to 3D seismic data at Marlim Field, Campos Basin, to recover acoustic impedance and porosity of the turbidites reservoirs. The Marlim sandstones consist of an Oligocene/Miocene deepwater turbidite system forming a series of amalgamated bodies. The main advantage of our workflow is to incorporate the interpreter’s knowledge about the local stratigraphy to construct an enhanced background model, and then extract a higher resolution image from the seismic data. High-porosity zones were associated to the reservoirs facies; meanwhile, the nonreservoir facies were identified as low-porosity zones.

Reservoir Prediction Under Control of Sedimentary Facies

2017 ◽  
Vol 25 (03) ◽  
pp. 1750022
Author(s):  
Xiuwei Yang ◽  
Peimin Zhu
Keyword(s):  
Seismic Data ◽  
Low Frequency ◽  
Prediction Method ◽  
Rock Physics ◽  
Real Data ◽  
Sedimentary Facies ◽  
Seismic Inversion ◽  
Rock Properties ◽  
Reservoir Prediction ◽  
Frequency Model

Acoustic impedance (AI) from seismic inversion can indicate rock properties and can be used, when combined with rock physics, to predict reservoir parameters, such as porosity. Solutions to seismic inversion problem are almost nonunique due to the limited bandwidth of seismic data. Additional constraints from well log data and geology are needed to arrive at a reasonable solution. In this paper, sedimentary facies is used to reduce the uncertainty in inversion and rock physics modeling; the results not only agree with seismic data, but also conform to geology. A reservoir prediction method, which incorporates seismic data, well logs, rock physics and sedimentary facies, is proposed. AI was first derived by constrained sparse spike inversion (CSSI) using a sedimentary facies dependent low-frequency model, and then was transformed to reservoir parameters by sequential simulation, statistical rock physics and [Formula: see text]-model. Two numerical experiments using synthetic model and real data indicated that the sedimentary facies information may help to obtain a more reasonable prediction.

Incorporation of geology with rock physics enables subsalt poststack inversion: A case study in the Gulf of Mexico

Geophysics ◽  
2011 ◽  
Vol 76 (5) ◽  
pp. WB53-WB65 ◽  
Author(s):  
Huyen Bui ◽  
Jennifer Graham ◽  
Shantanu Kumar Singh ◽  
Fred Snyder ◽  
Martiris Smith
Keyword(s):  
Seismic Data ◽  
Acoustic Impedance ◽  
Low Frequency ◽  
Rock Physics ◽  
Seismic Inversion ◽  
Inversion Method ◽  
Reservoir Properties ◽  
Blind Test ◽  
Frequency Model ◽  
Layer Sequence

One of the main goals of seismic inversion is to obtain high-resolution relative and absolute impedance for reservoir properties prediction. We aim to study whether the results from seismic inversion of subsalt data are sufficiently robust for reliable reservoir characterization. Approximately [Formula: see text] of poststack, wide-azimuth, anisotropic (vertical transverse isotropic) wave-equation migration seismic data from 50 Outer Continental Shelf blocks in the Green Canyon area of the Gulf of Mexico were inverted in this study. A total of four subsalt wells and four subsalt seismic interpreted horizons were used in the inversion process, and one of the wells was used for a blind test. Our poststack inversion method used an iterative discrete spike inversion method, based on the combination of space-adaptive wavelet processing to invert for relative acoustic impedance. Next, the dips were estimated from seismic data and converted to a horizon-like layer sequence field that was used as one of the inputs into the low-frequency model. The background model was generated by incorporating the well velocities, seismic velocity, seismic interpreted horizons, and the previously derived layer sequence field in the low-frequency model. Then, the relative acoustic impedance volume was scaled by adding the low-frequency model to match the calculated acoustic impedance logs from the wells for absolute acoustic impedance. Finally, the geological information and rock physics data were incorporated into the reservoir properties assessment for sand/shale prediction in two main target reservoirs in the Miocene and Wilcox formations. Overall, the poststack inversion results and the sand/shale prediction showed good ties at the well locations. This was clearly demonstrated in the blind test well. Hence, incorporating rock physics and geology enables poststack inversion in subsalt areas.

Characterization of a carbonate geothermal reservoir using rock-physics-guided deep neural networks

2021 ◽  
Vol 40 (10) ◽  
pp. 751-758
Author(s):  
Fabien Allo ◽  
Jean-Philippe Coulon ◽  
Jean-Luc Formento ◽  
Romain Reboul ◽  
Laure Capar ◽  
...  
Keyword(s):  
Neural Networks ◽  
Seismic Data ◽  
Deep Neural Networks ◽  
Synthetic Data ◽  
Rock Physics ◽  
Seismic Inversion ◽  
Geothermal Reservoir ◽  
Rock Properties ◽  
Hybrid Techniques ◽  
Geothermal Wells

Deep neural networks (DNNs) have the potential to streamline the integration of seismic data for reservoir characterization by providing estimates of rock properties that are directly interpretable by geologists and reservoir engineers instead of elastic attributes like most standard seismic inversion methods. However, they have yet to be applied widely in the energy industry because training DNNs requires a large amount of labeled data that is rarely available. Training set augmentation, routinely used in other scientific fields such as image recognition, can address this issue and open the door to DNNs for geophysical applications. Although this approach has been explored in the past, creating realistic synthetic well and seismic data representative of the variable geology of a reservoir remains challenging. Recently introduced theory-guided techniques can help achieve this goal. A key step in these hybrid techniques is the use of theoretical rock-physics models to derive elastic pseudologs from variations of existing petrophysical logs. Rock-physics theories are already commonly relied on to generalize and extrapolate the relationship between rock and elastic properties. Therefore, they are a useful tool to generate a large catalog of alternative pseudologs representing realistic geologic variations away from the existing well locations. While not directly driven by rock physics, neural networks trained on such synthetic catalogs extract the intrinsic rock-physics relationships and are therefore capable of directly estimating rock properties from seismic amplitudes. Neural networks trained on purely synthetic data are applied to a set of 2D poststack seismic lines to characterize a geothermal reservoir located in the Dogger Formation northeast of Paris, France. The goal of the study is to determine the extent of porous and permeable layers encountered at existing geothermal wells and ultimately guide the location and design of future geothermal wells in the area.

A time-lapse seismic repeatability test using the P-Cable high-resolution 3D marine acquisition system

2020 ◽  
Vol 39 (7) ◽  
pp. 480-487
Author(s):  
Patrick Smith ◽  
Brandon Mattox
Keyword(s):  
High Resolution ◽  
Seismic Data ◽  
Low Cost ◽  
Low Frequency ◽  
Time Lapse ◽  
Seismic Signal ◽  
Residual Energy ◽  
Acquisition System ◽  
Positioning Errors ◽  
Seismic Surveying

The P-Cable high-resolution 3D marine acquisition system tows many short, closely separated streamers behind a small source. It can provide 3D seismic data of very high temporal and spatial resolution. Since the system is containerized and has small dimensions, it can be deployed at short notice and relatively low cost, making it attractive for time-lapse seismic reservoir monitoring. During acquisition of a 3D high-resolution survey in the Gulf of Mexico in 2014, a pair of sail lines were repeated to form a time-lapse seismic test. We processed these in 2019 to evaluate their geometric and seismic repeatability. Geometric repetition accuracy was excellent, with source repositioning errors below 10 m and bin-based receiver positioning errors below 6.25 m. Seismic data comparisons showed normalized root-mean-square difference values below 10% between 40 and 150 Hz. Refinements to the acquisition system since 2014 are expected to further improve repeatability of the low-frequency components. Residual energy on 4D difference seismic data was low, and timing stability was good. We conclude that the acquisition system is well suited to time-lapse seismic surveying in areas where the reservoir and time-lapse seismic signal can be adequately imaged by small-source, short-offset, low-fold data.

Application of instantaneous-frequency attribute and gamma-ray wireline logs in the delineation of lithology in Serbin field, Southeast Texas: A case study

2018 ◽  
Vol 6 (4) ◽  
pp. T1023-T1043 ◽  
Author(s):  
Osareni C. Ogiesoba ◽  
William A. Ambrose ◽  
Robert G. Loucks
Keyword(s):  
Instantaneous Frequency ◽  
Acoustic Impedance ◽  
High Frequency ◽  
Gamma Ray ◽  
Low Frequency ◽  
High Porosity ◽  
Southeastern Part ◽  
High Gamma ◽  
Southeast Texas ◽  
Frequency Map

Although Serbin field in Southeast Texas was discovered in 1987, lithologic and petrophysical properties in the southeastern part of the field have not been fully evaluated. We have generated instantaneous frequency from 3D seismic data and predicted gamma-ray response volume from seismic attributes. By extracting maps of the instantaneous frequency and gamma-ray response along interpreted horizons, and crossplotting the instantaneous frequency against gamma-ray logs and integrating core data, we generated lithology maps to identify shale-prone zones that stratigraphically trapped hydrocarbons in the southeastern part of the field. We determine that Serbin field is separated into two areas: (1) a high-frequency, high-gamma-ray, and high-acoustic-impedance area in the northwest and (2) a low-frequency, low-gamma-ray, and low-acoustic-impedance area located in the southeast. By developing a lithologic map and relating it to the corresponding instantaneous-frequency map and log data, we also find that the southeastern part of the field can be divided into three zones: (1) zone 1, composed of approximately 0.7–2.7 m (approximately 2–8 ft) thick sandstone-rich beds of moderate frequency (25–30 Hz); (2) zone 2, composed of high-frequency (33–60 Hz) shale-rich zones that serve as stratigraphic-trapping-mechanisms; and (3) zone 3, composed of approximately 1.7–4 m (approximately 5–13 ft) thick sandstone-rich beds of low frequency (0–18 Hz) and relatively high porosity. These methods can be applied in other areas of the field with limited well control.

Low frequency component of seismic data estimation and its application in seismic inversion

2020 ◽  
Author(s):  
Ding Jicai ◽  
Zhao Xiaolong ◽  
Jiang Xiudi ◽  
Wang Yandong ◽  
Huang Xiaogang ◽  
...  
Keyword(s):  
Seismic Data ◽  
Low Frequency ◽  
Frequency Component ◽  
Seismic Inversion ◽  
Data Estimation

Hydrocarbon identification using the AVO response correction method based on high-resolution complex spectral decomposition

2020 ◽  
Vol 8 (1) ◽  
pp. SA49-SA61
Author(s):  
Huihuang Tan ◽  
Donghong Zhou ◽  
Shengqiang Zhang ◽  
Zhijun Zhang ◽  
Xinyi Duan ◽  
...  
Keyword(s):  
High Resolution ◽  
Seismic Data ◽  
Spectral Decomposition ◽  
Oil And Gas ◽  
Low Frequency ◽  
Seismic Signal ◽  
Correction Method ◽  
Bohai Bay ◽  
Oil And Gas Exploration ◽  
Response Correction

Amplitude-variation-with-offset (AVO) technique is one of the primary quantitative hydrocarbon discrimination methods with prestack seismic data. However, the prestack seismic data are usually have low data quality, such as nonflat gathers and nonpreserved amplitude due to absorption, attenuation, and/or many other reasons, which usually lead to a wrong AVO response. The Neogene formations in the Huanghekou area of the Bohai Bay Basin are unconsolidated clastics with a high average porosity, and we find that the attenuation on seismic signal is very strong, which causes an inconsistency of AVO responses between seismic gathers and its corresponding synthetics. Our research results indicate that the synthetic AVO response can match the field seismic gathers in the low-frequency end, but not in the high-frequency components. Thus, we have developed an AVO response correction method based on high-resolution complex spectral decomposition and low-frequency constraint. This method can help to achieve a correct high-resolution AVO response. Its application in Bohai oil fields reveals that it is an efficient way to identify hydrocarbons in rocks, which provides an important technique for support in oil and gas exploration and production in this area.

High-resolution reservoir characterization by an acoustic impedance inversion of a Tertiary deltaic clinoform system in the North Sea

Geophysics ◽  
2010 ◽  
Vol 75 (6) ◽  
pp. O57-O67 ◽  
Author(s):  
Daria Tetyukhina ◽  
Lucas J. van Vliet ◽  
Stefan M. Luthi ◽  
Kees Wapenaar
Keyword(s):  
North Sea ◽  
Seismic Data ◽  
Reservoir Characterization ◽  
Structural Information ◽  
Sampling Rate ◽  
Seismic Inversion ◽  
Acoustic Properties ◽  
The North ◽  
The North Sea ◽  
Well Data

Fluvio-deltaic sedimentary systems are of great interest for explorationists because they can form prolific hydrocarbon plays. However, they are also among the most complex and heterogeneous ones encountered in the subsurface, and potential reservoir units are often close to or below seismic resolution. For seismic inversion, it is therefore important to integrate the seismic data with higher resolution constraints obtained from well logs, whereby not only the acoustic properties are used but also the detailed layering characteristics. We have applied two inversion approaches for poststack, time-migrated seismic data to a clinoform sequence in the North Sea. Both methods are recursive trace-based techniques that use well data as a priori constraints but differ in the way they incorporate structural information. One method uses a discrete layer model from the well that is propagated laterally along the clinoform layers, which are modeled as sigmoids. The second method uses a constant sampling rate from the well data and uses horizontal and vertical regularization parameters for lateral propagation. The first method has a low level of parameterization embedded in a geologic framework and is computationally fast. The second method has a much higher degree of parameterization but is flexible enough to detect deviations in the geologic settings of the reservoir; however, there is no explicit geologic significance and the method is computationally much less efficient. Forward seismic modeling of the two inversion results indicates a good match of both methods with the actual seismic data.

Accurate poststack acoustic-impedance inversion by well-log calibration

Geophysics ◽  
2009 ◽  
Vol 74 (5) ◽  
pp. R59-R67 ◽  
Author(s):  
Igor B. Morozov ◽  
Jinfeng Ma
Keyword(s):  
Seismic Data ◽  
Acoustic Impedance ◽  
Joint Inversion ◽  
Low Frequency ◽  
Real Data ◽  
Data Sets ◽  
Frequency Model ◽  
Physical Constraints ◽  
Impedance Inversion ◽  
Reliable Solution

The seismic-impedance inversion problem is underconstrained inherently and does not allow the use of rigorous joint inversion. In the absence of a true inverse, a reliable solution free from subjective parameters can be obtained by defining a set of physical constraints that should be satisfied by the resulting images. A method for constructing synthetic logs is proposed that explicitly and accurately satisfies (1) the convolutional equation, (2) time-depth constraints of the seismic data, (3) a background low-frequency model from logs or seismic/geologic interpretation, and (4) spectral amplitudes and geostatistical information from spatially interpolated well logs. The resulting synthetic log sections or volumes are interpretable in standard ways. Unlike broadly used joint-inversion algorithms, the method contains no subjectively selected user parameters, utilizes the log data more completely, and assesses intermediate results. The procedure is simple and tolerant to noise, and it leads to higher-resolution images. Separating the seismic and subseismic frequency bands also simplifies data processing for acoustic-impedance (AI) inversion. For example, zero-phase deconvolution and true-amplitude processing of seismic data are not required and are included automatically in this method. The approach is applicable to 2D and 3D data sets and to multiple pre- and poststack seismic attributes. It has been tested on inversions for AI and true-amplitude reflectivity using 2D synthetic and real-data examples.

Sign in / Sign up

Export Citation Format

Share Document