Survey Design Considerations for Full Azimuth Acquisition Using a Single Recording Vessel

2009 ◽  
Author(s):  
David Hill* ◽  
Gordon Brown ◽  
Rob Campbell ◽  
Ed Hager
Keyword(s):  
Survey Design ◽  
Design Considerations

scholarly journals Vehicle-to-Pedestrian Communication for Vulnerable Road Users: Survey, Design Considerations, and Challenges

Sensors ◽  
2019 ◽  
Vol 19 (2) ◽  
pp. 358 ◽  
Author(s):  
Parag Sewalkar ◽  
Jochen Seitz
Keyword(s):  
Communication Systems ◽  
Survey Design ◽  
Communication Technologies ◽  
Road User ◽  
Design Parameters ◽  
Design Considerations ◽  
Road Users ◽  
Vulnerable Road User ◽  
Vulnerable Road Users

In the last few years, increasing attention has been provided to research Vehicle-to-Pedestrian (V2P) communication systems. These V2P systems serve different purposes (safety or convenience) and cater to different Vulnerable Road User (VRU) groups. Also, these V2P systems employ different communication technologies, and use different mechanisms to interact with the users. An effective V2P system also needs to consider varying characteristics of different VRUs. These various elements may be considered as design parameters of the V2P system. In this paper, we discuss such elements and propose a design framework for the V2P system based on them. We also provide an extensive survey of existing V2P efforts for safety and convenience applications and their design considerations. We perform a case study that compares the different approaches of V2P safety system for different VRU groups under different pre-crash scenarios. Finally, we discuss a few technological challenges in integration of VRUs into V2X systems.

LATENCY REDUCTION IN VLSI ROUTERS

1993 ◽  
Vol 03 (04) ◽  
pp. 485-494
Author(s):  
CHRIS JESSHOPE
Keyword(s):  
Degrees Of Freedom ◽  
Parallel Machines ◽  
Survey Design ◽  
Data Access ◽  
Parallel Computers ◽  
Low Latency ◽  
Message Delivery ◽  
Local Data ◽  
Latency Reduction ◽  
Design Considerations

This paper presents recent results on the MP1 router chip designed to implement scalable parallel computers. We survey design considerations used in order to reduce message delivery latency to a minimum. Results will be presented of simulations of the MP1 network which back up these considerations. It will be shown that there are many degrees of freedom in implementation and that implementation issues will often overwhelm other considerations, those on which simulation is focused, leading to anomalous predictions from those results. An example will be given on this. Even ultra-low latency networks will still have access times to remote data which are 10 to 100 times that for access to local data and architectures which tolerate low latency data-access must be exploited if scalable performance is to be obtained in these parallel machines based on networks.

scholarly journals SKA weak lensing– II. Simulated performance and survey design considerations

2016 ◽  
Vol 463 (4) ◽  
pp. 3686-3698 ◽  
Author(s):  
Anna Bonaldi ◽  
Ian Harrison ◽  
Stefano Camera ◽  
Michael L. Brown
Keyword(s):  
Survey Design ◽  
Weak Lensing ◽  
Design Considerations ◽  
Simulated Performance

Morphological behavior of compatibilized ternary blends prepared by mechanical mixing

1993 ◽  
Vol 51 ◽  
pp. 1200-1201
Author(s):  
S.D. Smith ◽  
R.J. Spontak ◽  
D.H. Melik ◽  
S.M. Buehler ◽  
K.M. Kerr ◽  
...  
Keyword(s):  
Interfacial Adhesion ◽  
Diblock Copolymers ◽  
Ternary Blends ◽  
Mechanical Mixing ◽  
Design Considerations ◽  
Covalently Bonded ◽  
Homopolymer Blends ◽  
Emulsifying Agent ◽  
Surface Active ◽  
Low Entropy

When blended together, homopolymers A and B will normally macrophase-separate into relatively large (≫1 μm) A-rich and B-rich phases, between which exists poor interfacial adhesion, due to a low entropy of mixing. The size scale of phase separation in such a blend can be reduced, and the extent of interfacial A-B contact and entanglement enhanced, via addition of an emulsifying agent such as an AB diblock copolymer. Diblock copolymers consist of a long sequence of A monomers covalently bonded to a long sequence of B monomers. These materials are surface-active and decrease interfacial tension between immiscible phases much in the same way as do small-molecule surfactants. Previous studies have clearly demonstrated the utility of block copolymers in compatibilizing homopolymer blends and enhancing blend properties such as fracture toughness. It is now recognized that optimization of emulsified ternary blends relies upon design considerations such as sufficient block penetration into a macrophase (to avoid block slip) and prevention of a copolymer multilayer at the A-B interface (to avoid intralayer failure).

Theoretical And Practical Design Considerations for Ultra-High Resolution Electron Lenses

1980 ◽  
Vol 38 ◽  
pp. 266-269
Author(s):  
Y. Harada ◽  
K. Tsuno ◽  
Y. Arai
Keyword(s):  
Optical Properties ◽  
High Resolution ◽  
Chromatic Aberration ◽  
Point Of View ◽  
Pole Piece ◽  
Axial Field ◽  
Design Considerations ◽  
Resolution Electron ◽  
Practical Design ◽  
Peak Flux

Magnetic objective lenses, from the point of view of pole piece geometry, can he roughly classified into two types, viz., symmetrical and asymmetrical. In the case of the former, the optical properties have been calculated by several authors1-3) and the results would appear to suggest that, in order to reduce the spherical and chromatic aberration coefficients, Cs and Cc, it is necessary to decrease the half-width value of the axial field distribution and to increase the peak flux density. The expressions for either minimum Cs or minimum Cc were presented in the form of ‘universal’ curves by Mulvey and Wallington4).

Sign in / Sign up

Export Citation Format

Share Document