Possible wear mechanisms at the wear-flat of rock cutting tools

2020 ◽  
pp. 7-17
Author(s):  
H.J.R. Deketh
Keyword(s):  
Wear Mechanisms ◽  
Cutting Tools ◽  
Rock Cutting

scholarly journals The design of bottomhole assembly with two rock cutting tools for directional drilling

2018 ◽  
pp. 14-20
Author(s):  
I. V. Voievidko ◽  
V. V. Tokaruk ◽  
M. A. Bodzian
Keyword(s):  
Theoretical Analysis ◽  
Inclination Angle ◽  
Large Diameter ◽  
Cutting Tools ◽  
Intensity Variation ◽  
Rock Cutting ◽  
Hole Drilling ◽  
Directional Drilling ◽  
Geological Conditions ◽  
Technical Factors

On the basis of the theoretical analysis and practical studies of hole drilling of large diameter, a method for designing the BHA with two rock cutting tools is proposed, taking into account the geological and technical factors that have an impact on the formation of the trajectory. The calculation of BHA with two rock cutting tools and a different number of supporting and centralizing components for different geological conditions of drilling is carried out and the analysis of their work in the process of drilling is conducted. The graphic dependences of the deviation intensity variation and the inclination angle with the sinking of borehole of the large diameter for the BHA that can be used for the drilling of vertical and directional wells.

Performance and wear mechanisms of PCD and pcBN cutting tools during machining titanium alloy Ti6Al4V

Wear ◽  
2020 ◽  
Vol 454-455 ◽  
pp. 203329
Author(s):  
Rebecka Lindvall ◽  
Filip Lenrick ◽  
Henrik Persson ◽  
Rachid M'Saoubi ◽  
Jan-Eric Ståhl ◽  
...  
Keyword(s):  
Titanium Alloy ◽  
Wear Mechanisms ◽  
Cutting Tools ◽  
Titanium Alloy Ti6al4v

Study on Tool Life and Tool Wear Mechanisms in Dry Cutting Pure Iron

2013 ◽  
Vol 770 ◽  
pp. 74-77 ◽  
Author(s):  
Jin Xing Kong ◽  
Liang Li ◽  
Dong Ming Xu ◽  
Ning He
Keyword(s):  
Tool Wear ◽  
Tool Life ◽  
Wear Mechanisms ◽  
Pure Iron ◽  
Cutting Tools ◽  
Cutting Parameters ◽  
Cutting Condition ◽  
High Plasticity ◽  
Dry Cutting ◽  
Tool Wear Mechanisms

Pure iron is a kind of high plasticity and toughness material. In the process of cutting pure iron, the tool wear is very serious. In this paper, three kinds of cutting tools KC5010, K313 and 1105 are used in the cutting pure iron process and the tool wear tests in dry cutting condition with different cutting parameters have been carried out. According to the results, the tool wear mechanisms and tool life of three kinds of cutting tools have been compared and analyzed. It is concluded that the tool life of K313 is better than KC5010 and 1105 and the three kinds of tool mechanisms are primarily adhesion wear, diffusion wear and oxidation wear.

Cutting Performances, Mechanical Property and Microstructure of Ultra-Fine Grade Ti (C,N)-Based Cermets

2008 ◽  
Vol 375-376 ◽  
pp. 102-106
Author(s):  
Hai Dong Yang ◽  
Xi Quan Xia ◽  
Wen Lin Chen ◽  
Ning Liu ◽  
Chong Gao Zhang
Keyword(s):  
Carbon Steel ◽  
Wear Mechanisms ◽  
Bending Strength ◽  
Cutting Tools ◽  
Medium Carbon Steel ◽  
Dry Cutting ◽  
Medium Carbon ◽  
Resistance To Oxidation ◽  
Thermal Wear ◽  
Key Aspects

The two cutting tools obtained from ultra-fine grade Ti (C,N)-based cermets were tested in the dry cutting of a medium carbon steel (AISI1045). Microstructure and mechanical properties were studied. Wear mechanisms (mainly diffusion and oxidation) were investigated in detail and compared each other in order to better understand key aspects due to thermal wear mechanisms. Comparing tool A with B, under the adopted cutting conditions, the tool A has a better resistance to oxidation deformation in machining medium carbon steel due to the higher hardness, although tool B has higher bending strength and fracture toughness.

Research on the Wear Characteristics and Wear Mechanisms of CrAlTiN Coated HSS Tools under Dry Cutting Conditions

2012 ◽  
Vol 562-564 ◽  
pp. 619-622
Author(s):  
Ji Ming Xiao ◽  
Li Jing Bai ◽  
Yan Li ◽  
Jian Ming Zheng ◽  
Qi Long Yuan
Keyword(s):  
Magnetron Sputtering ◽  
Wear Mechanisms ◽  
High Speed ◽  
Complex Shape ◽  
Adhesive Wear ◽  
Cutting Tools ◽  
High Speed Steel ◽  
Dry Cutting ◽  
Wear Characteristics ◽  
The Face

High-speed steel (HSS) turning tools was designed and sharpened according to the angles of the complex shape cutting tools. CrAlTiN coating was deposited using unbalance magnetron sputtering plating technique. By dry turning tests, the wear characteristics and wear mechanisms of the face were investigated. The results show that the face wear of the coated HSS tools is obviously different from that of the uncoated tools, the crater width is smaller, the boundary is jagged and the lowest position is away from the major cutting edge. Adhesive wear and local adhesive wear are the main wear mechanisms.

Sign in / Sign up

Export Citation Format

Share Document