Alkali Activated Cementitious Materials in Chemically Aggressive Environments

Materials ◽  
2020 ◽  
Vol 13 (16) ◽  
pp. 3467
Author(s):  
Ankit Kothari ◽  
Karin Habermehl-Cwirzen ◽  
Hans Hedlund ◽  
Andrzej Cwirzen

Most of the currently used concretes are based on ordinary Portland cement (OPC) which results in a high carbon dioxide footprint and thus has a negative environmental impact. Replacing OPCs, partially or fully by ecological binders, i.e., supplementary cementitious materials (SCMs) or alternative binders, aims to decrease the carbon dioxide footprint. Both solutions introduced a number of technological problems, including their performance, when exposed to low, subfreezing temperatures during casting operations and the hardening stage. This review indicates that the present knowledge enables the production of OPC-based concretes at temperatures as low as −10 °C, without the need of any additional measures such as, e.g., heating. Conversely, composite cements containing SCMs or alkali-activated binders (AACs) showed mixed performances, ranging from inferior to superior in comparison with OPC. Most concretes based on composite cements require pre/post heat curing or only a short exposure to sub-zero temperatures. At the same time, certain alkali-activated systems performed very well even at −20 °C without the need for additional curing. Chemical admixtures developed for OPC do not always perform well in other binder systems. This review showed that there is only a limited knowledge on how chemical admixtures work in ecological concretes at low temperatures and how to accelerate the hydration rate of composite cements containing high amounts of SCMs or AACs, when these are cured at subfreezing temperatures.


2014 ◽  
Vol 1000 ◽  
pp. 118-121 ◽  
Author(s):  
Pavel Rovnaník ◽  
Patrik Bayer

Alkali-activated slag (AAS) is a material which has great potential for use in building industry. The aim of this work was to gain new superior properties by the addition of carbon nanotubes (CNTs). This material can act as a microreinforcement improving mechanical properties of cementitious materials. The effect of 0–1 wt.% addition of CNTs on the mechanical properties, hydration characteristics and microstructure of AAS binder was determined. The addition of CNTs delays the setting of the binder and a partial deterioration of strength parameters was observed.


2010 ◽  
Vol 452-453 ◽  
pp. 721-724
Author(s):  
Gum Sung Ryu ◽  
Hyun Jin Kang ◽  
Su Tae Kang ◽  
Gyung Taek Koh ◽  
Jang Hwa Lee

Recently, research on alkali-activated concrete that does not use cement as binder has been actively conducted. This alkali-activated concrete is a cement zero concrete which, instead of cement, is activated by alkali solution using fly ash known to be rich of Si and Al and enables to reduce effectively the emission of CO2 gas. This paper presents a basic study for the manufacture of cementless concrete using 100% of fly ash. To that goal, the mechanical characteristics of cementless concrete is evaluated according to the age and the variation of the molar concentration of the alkali activator with focus on the identification of the reaction mechanism. The experimental results show that larger molar concentration elutes larger quantities of Si4+ and Al3+. Specifically, approximately twice larger quantities of Si4+ and Al3+ were eluted for molar concentrations of 9M and 12M than 6M. The formation of gel at the surface of fly ash appeared to be caused by the stronger activation of fly ash in higher alkali environment. The resulting compressive strengths per age indicated that the strength of concrete could be controlled according to the molar concentration of NaOH. Moreover, results also demonstrated that a molar concentration of 9M for NaOH seems to be appropriate to secure a strength superior to 40MPa as the reference for high strength concrete in ordinary concrete.


Chemosphere ◽  
2017 ◽  
Vol 168 ◽  
pp. 300-308 ◽  
Author(s):  
Xiao Huang ◽  
RanLiang Zhuang ◽  
Faheem Muhammad ◽  
Lin Yu ◽  
YanChyuan Shiau ◽  
...  

2021 ◽  
Author(s):  
Thi Nhan Nguyen ◽  
Quoc Phung ◽  
Ziyou Yu ◽  
Lander Frederickx ◽  
Diederik Jacques ◽  
...  

Abstract Carbonation of alkali activated materials is one of the main deteriorations affecting their durability. However, current understanding in structural alteration of these materials exposed to an environment inducing carbonation at nano/micro scale remains limited. This study examined the evolution of phase assemblages of alkali activated slag mortars subjected to accelerated carbonation (1% CO2, 60% relative humidity, up to 28 day carbonation) using XRD, FTIR and 29Si, 27Al, 23Na MAS NMR. Samples with three water to binder (w/b) ratios (0.35, 0.45, and 0.55) were investigated. The results show that the phase assemblages mainly consisted of C-A-S-H, disordered remnant aluminosilicate binder, and a minor hydrotalcite as a secondary product. Upon carbonation, calcium carbonate is mainly formed as the vaterite polymorph, while no sodium carbonate is found after carbonation as commonly reported. The sodium acts primarily as a charge balancing ion without producing sodium carbonate as a final carbonation product in 28-day carbonated materials. The C-A-S-H structure becomes more cross-linked due to the decalcification of this phase evidenced by the appearance of Q4 groups, which replace the Q1 and Q2 ones as observed in the 29Si MAS NMR spectra, and the dominance of Al (IV) in 27Al MAS NMR. Especially, unlike cementitious materials, the influence of w/b ratio on the crystalline phase formation and structure of C-A-S-H in the alkali activated mortars before and after carbonation is limited.


Sign in / Sign up

Export Citation Format

Share Document