X-Ray Fluorescence Excited with Protons and Heavy Ions, the Cross Sections Curve

2005 ◽  
pp. 9 ◽  
Author(s):  
C. M. Romo-Kröger
Keyword(s):  
X Ray ◽  
1970 ◽  
Vol 14 ◽  
pp. 173-183 ◽  
Author(s):  
J. A. Cairns ◽  
D. F. Holloway ◽  
R. S. Nelson

AbstractIncreasing attention is currently focused on the generation of characteristic x-ray by proton irradiation. This has the advantage of yielding “clean” x-ray- i. e. free from background brerasstrahlung radiation, from even the lightest elements. The disadvantage is that the yields are naturally much lower than those produced by electrons of the same energy. A recent study has extended characteristic x-ray production to a variety of heavy ions and has shown that the cross- sections for the production of clean x-rays are often higher , by as much as several orders of magnitude, than those produced by protons of the same energy. In addition, there has emerged a further advantage, viz. the ability of specially chosen heavy ions to excite characteristic x-ray from a particular element in a selective manner. Since heavy ions penetrate only a few hundred Angstroms in to most solids, the phenomenon can be used as the basis of a technique for the examination of surface deposits, or to measure depth distributions of impurities. For example, Kr ions can be used t o determine the range distribution of antimony which had been implanted in to silicon at 100 keV. The antimony concentration was determined as a function of ∼ 150 Å steps, and was found to exhibit a maximum concentration of ∼ 1 part in 103 of silicon at 450 Å below the surface, falling to zero concentration at ∼2000 Å a depth. In the past, in order to obtain the required degree of sensitivity, such range determinations have relied on radio active tracer techniques.An entirely new type of proportional counter has been developed during the course of these studies. This instrument, because of its special construction, can be positioned very close to targets in non-dispersive studies, so as to collect the highest possible fraction of emitted x-ray. It incorporates a replaceable anode unit, together with a built- in miniature head amplifier, and exhibits extremely good performance, particularly for ultra-soft x-ray. In addition, rotation of a dial on the end of the counter body allows alteration of the active gas volume during operation, and so permits tuning into x-rays of a particular energy.


1984 ◽  
Vol 413 (3) ◽  
pp. 489-502
Author(s):  
R. Bimbot ◽  
D. Gardes ◽  
L. De Reilhac ◽  
M.F. Rivet ◽  
A. Fleury ◽  
...  

1977 ◽  
Vol 21 ◽  
pp. 119-127
Author(s):  
M. O. Krause ◽  
E. Ricci ◽  
C. J. Sparks ◽  
C. W. Nestor

Exact expressions are given for the K and L x-ray fluorescence cross sections. Hole transfer between the L subshells is taken into account and shown to lead to a substantial enhancement of the cross sections for x rays of the L2 and L3 emission series. Absolute values of Kα and Lα cross sections are calculated for all elements and four excitation energies, namely GeK ≙ 10.0 keV, MoKα ≙ 17.44 keV, AgK ≙ 22.5 keV and Am 241 ≙ 59.6 keV.


2013 ◽  
Vol 802 ◽  
pp. 174-178
Author(s):  
Bhawan Muangwaeng ◽  
Surasit Rojananan ◽  
Siriporn Rojananan

The aim of this work is to investigate the effect of injection parameters on morphology in stainless steel 316L metal injection moulding. In the experiment, samples were prepared by injection moulding process with varies parameters such as gate locations, pressures and speeds. The physical appearance of green parts was examined. After that, the cross sections of samples were investigated by scanning electron microscope including chemical analysis of the phase determined by x-ray energy dispersive spectroscopy. The experimental results showed that a perpendicular gate injection caused a separate section between outer skin and core at the cross section of specimens. The high pressure and speed for both injection directions caused crack. In conclusion, a parallel gate injection of feedstock with low pressure and speed was successful to mould the homogeneous samples without black streak, crack and phase separation. Therefore, the observed results could be useful to establish guideline for moulding in order to receive the complete green parts without defects


Sign in / Sign up

Export Citation Format

Share Document