An Improved Correlation for Two-Phase Frictional Pressure Drop in Boiling and Adiabatic Downflow in the Annular Flow Regime

Author(s):  
J F Klausner ◽  
B T Chao ◽  
S L Soo

An improved correlation is presented for annular two-phase frictional pressure drop data for vertical downflow. An ideal dimensionless film thickness based on the vapour volume fraction, a characteristic friction factor based on the two-phase frictional pressure gradient and a Weber number relevant for the interfacial capillary wave structure are the correlating parameters. The proposed new correlating scheme is tested against a wide range of data obtained in this investigation for refrigerant R11 in forced convection boiling and in adiabatic test sections of 19 mm cylindrical cross-section as well as published data for air-water and air-glycerine solution mixtures in the annular flow regime. Over 80 per cent of the measured values fall within ±30 per cent of those predicted from the correlation. Due to the wide range of liquid film thickness covered, 0.05–2.9 mm, its validity extends past the range where previously reported downflow pressure drop correlations fail. A paradox connected with previously reported annular downflow pressure drop correlations based on the liquid-vapour interfacial shear stress is pointed out. Upflow frictional pressure drop data in the annular flow regime can also be correlated by the proposed scheme.

Author(s):  
Braden A. McDermott ◽  
Timothy A. Shedd

A unique horizontal two-phase flow facility has been fabricated in an effort to understand the dynamics of two-phase flow in small pipes. The fluid chosen for study is the low pressure refrigerant R-123. In this work, two-phase pressure drop data were obtained for two-phase flow of refrigerant R-123 in a 17.0 mm inner diameter tube over a wide range of quality, from .015–1, and mass fluxes that were varied from 50 kg m−2 s−1 to 550 kg m−2 s−1. These data have been compared, as a whole and by regime, against four frequently-used two-phase frictional pressure drop prediction correlations. Flow regimes were visualized using a quartz tube at the end of the test section over this wide range of conditions, which ranged from stratified to annular flow. Each condition was mapped on the Mandhane, Taitel-Dukler, and Kattan-Favrat-Thome flow regime maps in an attempt to understand the applicability of each. Some discrepancies exist between the current data and the published flow maps, and recommendations are made based on these observations. The pressure drop data appear to be dependent upon the flow regime, suggesting that an entire set of correlations is necessary based upon flow regime for accurate prediction of pressure drop.


Author(s):  
Christian Weinmu¨ller ◽  
Dimos Poulikakos

Microfluidics has experienced a significant increase in research activities in recent years with a wide range of applications emerging, such as micro heat exchangers, energy conversion devices, microreactors, lab-on-chip devices and micro total chemical analysis systems (μTAS). Efforts to enhance or extend the performance of single phase microfluidic devices are met by two-phase flow systems [1, 2]. Essential for the design and control of microfluidic systems is the understanding of the fluid/hydrodynamic behavior, especially pressure drop correlations. These are well established for single phase flow, however, analytical correlations for two-phase flow only reflect experimentally obtained values within an accuracy of ± 50% [3, 4]. The present study illustrates the effect of two-phase flow regimes on the pressure drop. Experimental measurement data is put into relation of calculated values based on established correlations of Lockhart-Martinelli with Chisholm modifications for macroscopic flows [5, 6] and Mishima-Hibiki modifications for microscale flows [7]. Further, the experimental pressure drop data is superimposed onto two-phase flow maps to identify apparent correlations of pressure drop abnormalities and flow regimes. The experiments were conducted in a square microchannel with a width of 200 μm. Optical access is guaranteed by an anodically bonded glass plate on a MEMS fabricated silicon chip. Superficial velocities range from 0.01 m/s to 1 m/s for the gas flow and from 0.0001 m/s to 1 m/s for the liquid flow with water as liquid feed and CO2 as gas. The analysis of the flow regimes was performed by imaging the distinct flow regimes by laser induced fluorescence microscopy, employing Rhodamine B as the photosensitive dye. The pressure drop was synchronically recorded with a 200 mbar, 2.5 bar and 25 bar differential pressure transmitter and the data was exported via a LabView based software environment, see Figure 1. Figure 2 illustrates the experimentally obtained pressure drop in comparison to the calculated values based on the Lockhard-Martinelli correlation with the Chisholm modification and the Mishima-Hibiki modification. For both cases the predications underestimate the two-phase pressure drop by more than 50%. Nevertheless, the regression of the experimental data has an offset of linear nature. Two-phase flow is assigned to flow regime maps of bubbly, wedging, slug or annular flow defined by superficial gas and liquid velocities. In Figure 3 the pressure drop is plotted as a surface over the corresponding flow regime map. Transition lines indicate a change of flow regimes enclosing an area of an anticline in the pressure data. In the direct comparison between the calculated and the measured values, the two surfaces show a distinct deviation. Especially, the anticline of the experimental data is not explained by the analytical correlations. Figure 4 depicts the findings of Figure 3 at a constant superficial velocity of 0.0232 m/s. The dominant influence of the flow regimes on the pressure drop becomes apparent, especially in the wedging flow regime. The evident deviation of two-phase flow correlations for the pressure drop is based on omitting the influence of the flow regimes. In conclusion, the study reveals a strong divergence of pressure drop measurements in microscale two-phase flow from established correlations of Lockhart-Martinelli and recognized modifications. In reference to [8, 9], an analytical model incorporating the flow regimes and, hence, predicting the precise pressure drop would be of great benefit for hydrodynamic considerations in microfluidics.


2020 ◽  
Vol 44 (3) ◽  
pp. 362-384
Author(s):  
Amen Younes ◽  
Ibrahim Hassan ◽  
Lyes Kadem

A semi-analytical model for predicting heat transfer and pressure drop in annular flow regime for saturated flow boiling in a horizontal microtube at a uniform heat flux has been developed based on a one-dimensional separated flow model. More than 600 two-phase heat transfer, 498 two-phase pressure drop, and 153 void fraction experimental data points for annular flow regime were collected from the literature to validate the present model. The collected data were recorded for various working fluids, R134a, R1234ze, R236fa, R410a, R113, and CO2, for round macro- and microsingle horizontal tubes with an inner diameter range of 0.244 mm ≤ Dh ≤ 3.1 mm, a heated length to diameter ratio of 90 ≤ Lh/Dh ≤ 2000, a saturation temperature range of –10 ≤ Tsat ≤ +50 °C, and liquid to vapor density ratios in the range 6.4 ≤ ρf/ρg ≤ 188. The model was tested for laminar and turbulent flow boiling conditions corresponding to an equivalent Reynolds number, 1900 ≤ Reeq ≤ 48 000, and confinement number, 0.27 ≤ Cconf ≤ 3.4. Under the annular flow regime, the present model predicted the collected data of the heat transfer, pressure drop, and void fraction with mean absolute errors (MAE) of 18.14%, 23.02%, and 3.22%, respectively.


Volume 3 ◽  
2004 ◽  
Author(s):  
DuWayne Schubring ◽  
Timothy A. Shedd

In this study, non-intrusive pressure drop, liquid film thickness distribution and wave behavior measurements have been obtained for 140 and 220 two-phase flow conditions in horizontal 8.8 mm I.D and 15.1 mm I.D. tubes, respectively. Horizontal flow regimes ranging from stratified-wavy to annular were studied in long clear test sections. Pressure drop data appeared to show different trends for the wavy, wavy-annular and annular flow regimes, suggesting that a unique model may be required for each. In addition, wave frequency showed clearly different behavior for these regimes, with only minor liquid flow dependence in the wavy and wavy-annular flows and strong liquid flow dependence in annular flow. Interestingly, disturbance wave velocity could be correlated to within 10% by the gas friction velocity in the annular regime and within 20% in the wavy-annular regime, leading to a simple correlation between pressure drop and wave velocity. Base film thickness data (between waves) show that the film is relatively insensitive to gas flow at the side and top of the tube and that the film thickness around the tube becomes nearly independent of liquid flow rate at high gas flows. Empirical correlations of the various data sets are presented with the goal of aiding general horizontal two-phase flow modeling efforts.


Author(s):  
Kaipo Kekaula ◽  
Yitung Chen

Abstract Two-phase flow pressure drop during condensation of steam inside inclined tube heat exchangers was investigated over a wide range of ambient temperature. The ambient temperature changes from 3 to 45°C, the steam mass flux varies from 3 to 18 kg/(m2·s), vapor quality ranges from 0.51 to 0.86. 608 data points were experimentally obtained and compared with 8 commonly used correlations from the available literatures. Frictional pressure drop increases with increasing temperature difference and fan speed. For the full experimental dataset, the best overall performing correlation was obtained by using the Wallis correlation (MAPE = 17.60%, NRMSE = 14.87%). For cold ambient temperatures, (Tamb < 20°C, N=298), the best overall performing correlation was obtained by using the Carey correlation (MAPE = 11.02%, NRMSE = 14.71%). For hot ambient temperatures (Tamb >30°C, N = 196), the Lockhart and Martinelli correlation has shown the best performance (MAPE = 16.84%, NRMSE = 20.45%). An improved two-phase frictional pressure drop correlation based on the Wallis correlation [21] is proposed.


2004 ◽  
Vol 126 (1) ◽  
pp. 107-118 ◽  
Author(s):  
J. L. Pawloski ◽  
C. Y. Ching ◽  
M. Shoukri

The void fractions, flow regimes, and pressure drop of air-oil two-phase flow in a half-inch diameter pipe over a wide range of test conditions have been investigated. The flow regimes were identified with the aid of a 1000 frames per second high-speed camera. A capacitance sensor for instantaneous void fraction measurements was developed. The mean and probability density function of the instantaneous void fraction signal can be used to effectively identify the different flow regimes. The current flow regime data show significant differences in the transitional boundaries of the existing flow regime maps. Property correction factors for the flow regime maps are recommended. The pressure drop measurements were compared to the predictions from four existing two-phase flow pressure drop models. Though some of the models performed better for certain flow regimes, none of the models were found to give accurate results over the entire range of flow regimes.


2008 ◽  
Vol 130 (11) ◽  
Author(s):  
Yoon Jo Kim ◽  
Jeremy Jang ◽  
Predrag S. Hrnjak ◽  
Min Soo Kim

This paper presents the pressure drop data and the analysis of adiabatic CO2 flow in horizontal and vertical smooth and microfin tubes at saturation temperatures around −20°C. The test tubes had 3.48mm inner diameter smooth tube and a 3.51mm melt-down diameter microfin tube. The test was performed over a mass flux range of 200–800kg∕m2s and at saturation temperatures of −25°C and −15°C. The effects of various parameters—mass flux, saturated temperature, and tube diameter—on pressure drop were qualitatively analyzed. The analyses showed that the frictional pressure drop characteristics of vertical two-phase flow were much different from that of the horizontal two-phase flow. The microfin tube can be considered as “very rough tube” having the roughness of “fin height.” The data were compared with several correlations. The existing frictional pressure drop correlation is sufficient to predict the horizontal pressure drop in smooth tube. For the vertical pressure drop, the simple combination of the frictional pressure drop and void fraction model was in comparatively good agreement. However, the qualitative results showed that there were some limits to cover the different mechanisms related to the interfacial shear stress. The average enhancement factors and penalty factors evidenced that it was not always true that the internally finned geometry guaranteed the superior in-tube condensation performance of microfin tube in refrigeration system and air-conditioning systems.


Sign in / Sign up

Export Citation Format

Share Document